Datasheet

9
62001ff
LT6200/LT6200-5
LT6200-10/LT6201
SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS
V
OS
Input Offset Voltage V
CM
= Half Supply
V
CM
= V
+
V
CM
= V
–
l
l
l
1.9
3.5
3.5
4.5
7.5
7.5
mV
mV
mV
Input Offset Voltage Match
(Channel-to-Channel) (Note 11)
V
CM
= 0V
V
CM
= V
–
to V
+
l
l
0.2
0.4
2
3.6
mV
mV
V
OS
TC Input Offset Voltage Drift (Note 8) V
CM
= Half Supply
l
8.2 24 µV/ºC
I
B
Input Bias Current V
CM
= Half Supply
V
CM
= V
+
V
CM
= V
–
l
l
l
–40
–50
–10
8
–23
18
µA
µA
µA
∆I
B
I
B
Shift V
CM
= V
–
to V
+
l
31 68 µA
I
B
Match (Channel-to-Channel) (Note 11)
l
4 12 µA
I
OS
Input Offset Current V
CM
= Half Supply
V
CM
= V
+
V
CM
= V
–
l
l
l
1.3
1
3.5
10
10
15
µA
µA
µA
A
VOL
Large-Signal Gain V
O
= ±4.5V, R
L
= 1k
V
O
= ±2V, R
L
= 100
l
l
46
7.5
80
13.5
V/mV
V/mV
CMRR Common Mode Rejection Ratio V
CM
= V
–
to V
+
V
CM
= –2V to 2V
l
l
65
75
90
100
dB
dB
CMRR Match (Channel-to-Channel) (Note 11) V
CM
= –2V to 2V
l
75 105 dB
PSRR Power Supply Rejection Ratio V
S
= ±1.5V to ±5V
l
60 65 dB
PSRR Match (Channel-to-Channel) (Note 6) V
S
= ±1.5V to ±5V
l
60 100 dB
V
OL
Output Voltage Swing LOW (Note 7) No Load
I
SINK
= 5mA
I
SINK
= 20mA
l
l
l
16
60
170
75
125
310
mV
mV
mV
V
OH
Output Voltage Swing HIGH (Note 7) No Load
I
SOURCE
= 5mA
I
SINK
= 20mA
l
l
l
85
125
265
150
230
480
mV
mV
mV
I
SC
Short-Circuit Current
l
±60 ±90 mA
I
S
Supply Current
Disabled Supply Current
V
SHDN
= 0.3V
l
l
25
1.6
29
2.1
mA
mA
I
SHDN
SHDN Pin Current V
SHDN
= 0.3V
l
215 295 µA
V
L
V
SHDN
Pin Input Voltage LOW
l
0.3 V
V
H
V
SHDN
Pin Input Voltage HIGH
l
V
+
– 0.5 V
Shutdown Output Leakage Current V
SHDN
= 0.3V
l
0.1 75 µA
t
ON
Turn-On Time V
SHDN
= 0.3V to 4.5V, R
L
= 100Ω, V
S
= 5V
l
180 ns
t
OFF
Turn-Off Time V
SHDN
= 4.5V to 0.3V, R
L
= 100Ω, V
S
= 5V
l
180 ns
SR Slew Rate A
V
= –1, R
L
= 1k, V
O
= 4V
LT6200, LT6201
l
31 44 V/µs
A
V
= –10, R
L
= 1k, V
O
= 4V
LT6200-5
LT6200-10
l
l
125
260
180
370
V/µs
V/µs
FPBW Full Power Bandwidth (Note 9) V
OUT
= 3V
P-P
(LT6200-10)
l
27 39 MHz
elecTrical characTerisTics
The ● denotes the specifications which apply over –40°C < T
A
< 85°C
temperature range. Excludes the LT6201 in the DD package (Note 3). V
S
= ±5V, V
CM
= V
OUT
= 0V, V
SHDN
= OPEN, unless
otherwise noted. (Note 5)
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime
Note 2: Inputs are protected by back-to-back diodes. If the differential
input voltage exceeds 0.7V, the input current must be limited to less
than 40mA. This parameter is guaranteed to meet specified performance
through design and/or characterization. It is not 100% tested.