Datasheet
LT6003/LT6004/LT6005
7
600345fd
(LT6003H, LT6004H, LT6005H) The l denotes the specifications which apply
over the full specified temperature range of –40°C ≤ T
A
≤ 125°C. V
S
= ±8V, V
CM
= V
OUT
= half supply, R
L
to ground, unless otherwise
noted.
ELECTRICAL CHARACTERISTICS
SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS
V
OS
Input Offset Voltage LT6003S5, LT6004MS8
LT6005GN
LT6004DD, LT6005DHC
LT6003DC
l
l
l
l
1.6
1.8
2
2.2
mV
mV
mV
mV
ΔV
OS
/ΔT
Input Offset Voltage Drift (Note 5) S5, MS8, GN
DC, DD, DHC
l
l
2
3
6
8
µV/°C
µV/°C
I
B
Input Bias Current LT6003
LT6004, LT6005
l
l
6
12
nA
nA
I
OS
Input Offset Current LT6003
LT6004, LT6005
l
l
2
4
nA
nA
CMRR Common Mode Rejection Ratio V
CM
= –7.7V to 6.9V
V
CM
= –7.7V to 7.7V, S5, MS8, GN
V
CM
= –7.7V to 7.7V, DC, DD, DHC
l
l
l
90
78
76
dB
dB
dB
Input Offset Voltage Shift V
CM
= –7.7V to 6.9V
V
CM
= –7.7V to 7.7V, S5, MS8, GN
V
CM
= –7.7V to 7.7V, DC, DD, DHC
l
l
l
460
1.9
2.5
µV
mV
mV
Input Voltage Range Guaranteed by CMRR
l
–7.7 7.7 V
PSRR Power Supply Rejection Ratio V
S
= ±1.1V to ±8V
l
84 dB
V
OL
Output Swing Low (Notes 6, 8) No Load
I
SINK
= 100µA
l
l
60
275
mV
mV
V
OH
Output Swing High (Note 6) No Load
I
SOURCE
= 100µA
l
l
140
400
mV
mV
I
SC
Short Circuit Current Short to GND
l
1 mA
I
S
Supply Current per Amplifier
l
3 µA
SR Slew Rate (Note 11)
A
V
= –1, R
F
= R
G
= 1MΩ
l
0.2 V/ms
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: A heat sink may be required to keep the junction temperature
below absolute maximum. This depends on the power supply voltage and
how many amplifiers are shorted. The θ
JA
specified for the DC, DD and
DHC packages is with minimal PCB heat spreading metal. Using expanded
metal area on all layers of a board reduces this value.
Note 3: The LT6003C/LT6004C/LT6005C and LT6003I/LT6004I/LT6005I are
guaranteed functional over the temperature range of –40°C to 85°C. The
LT6003H/LT6004H/LT6005H are guaranteed functional over the operating
temperature range of –40°C to 125°C.
Note 4: The LT6003C/LT6004C/LT6005C are guaranteed to meet specified
performance from 0°C to 70°C. The LT6003C/LT6004C/LT6005C are
designed, characterized and expected to meet specified performance from
–40°C to 85°C but are not tested or QA sampled at these temperatures.
The LT6003I/LT6004I/LT6005I are guaranteed to meet specified
performance from –40°C to 85°C. The LT6003H/LT6004H/LT6005H are
guaranteed to meet specified performance from –40°C to 125°C.
Note 5: This parameter is not 100% tested.
Note 6: Output voltage swings are measured between the output and
power supply rails.
Note 7: Limits are guaranteed by correlation to V
S
= 5V tests.
Note 8: Limits are guaranteed by correlation to V
S
= 1.8V tests
Note 9: Limits are guaranteed by correlation to V
S
= ±8V tests
Note 10: Full-power bandwidth is calculated from the slew rate:
FPBW = SR/πV
P-P
.
Note 11: Slew rate measured at V
S
= 1.8V, V
OUT
= 0.4V to 1.4V is used to
guarantee by correlation the slew rate at V
S
= 5V, V
OUT
= 1V to 4V and the
slew rate at V
S
= ±8V, V
OUT
= –5V to 5V.