Datasheet

3
LT1222
1222fc
SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS
t
r
, t
f
Rise Time, Fall Time A
V
= 10, 10% to 90%, 0.1V 2.4 ns
Overshoot A
V
= 10, 0.1V 43 %
Propagation Delay A
V
= 10, 50% V
IN
to 50% V
OUT
, 0.1V 5.2 ns
t
s
Settling Time 10V Step, 0.1% 75 ns
10V Step, 0.01% 120 ns
Differential Gain A
V
= 2, C
C
= 50pF, f = 3.58MHz, R
L
= 150Ω (Note 7) 0.40 %
A
V
= 10, C
C
= 0pF, f = 3.58MHz, R
L
= 1k (Note 7) 0.15 %
Differential Phase A
V
= 2, C
C
= 50pF, f = 3.58MHz, R
L
= 150Ω (Note 7) 0.10 DEG
A
V
= 10, C
C
= 0pF, f = 3.58MHz, R
L
= 1k (Note 7) 0.01 DEG
R
O
Output Resistance A
V
= 10, f = 1MHz 0.1 Ω
I
S
Supply Current 8 10.5 mA
ELECTRICAL CHARACTERISTICS
V
S
= ±15V, T
A
= 25°C, V
CM
= 0V, unless otherwise specified.
SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS
V
OS
Input Offset Voltage (Note 4) ● 100 600 μV
Input V
OS
Drift ● 5 μV/°C
I
OS
Input Offset Current ● 100 400 nA
I
B
Input Bias Current ● 100 400 nA
CMRR Common Mode Rejection Ratio V
CM
= ±12V ● 100 120 dB
PSRR Power Supply Rejection Ratio V
S
= ±5V to ±15V ● 98 110 dB
A
VOL
Large-Signal Voltage Gain V
OUT
= ±10V, R
L
= 500Ω ● 100 200 V/mV
V
OUT
Output Swing R
L
= 500Ω ● 12 13 ±V
I
OUT
Output Current V
OUT
= ±12V ● 24 26 mA
SR Slew Rate (Note 5) ● 150 200 V/μs
I
S
Supply Current ● 811 mA
SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS
V
OS
Input Offset Voltage (Note 4) ● 100 600 μV
Input V
OS
Drift ● 5 μV/°C
I
OS
Input Offset Current ● 100 800 nA
I
B
Input Bias Current ● 100 1000 nA
CMRR Common Mode Rejection Ratio V
CM
= ±12V ● 98 120 dB
PSRR Power Supply Rejection Ratio V
S
= ±5V to ±15V ● 98 110 dB
A
VOL
Large-Signal Voltage Gain V
OUT
= ±10V, R
L
= 500Ω ● 50 200 V/mV
V
OUT
Output Swing R
L
= 500Ω ● 10 13 ±V
R
L
= 1k ● 12 13 ±V
I
OUT
Output Current V
OUT
= ±10V ● 20 26 mA
V
OUT
= ±12V ● 12 13 mA
SR Slew Rate (Note 5) ● 110 200 V/μs
I
S
Supply Current ● 811 mA
Note 1: Stresses beyond those listed under Absolute Maximum Ratings may
cause permanent damage to the device. Exposure to any Absolute Maximum
Rating condition for extended periods may affect device reliability and lifetime.
Note 2: A heat sink may be required when the output is shorted indefinitely.
Note 3: The LT1222C is guaranteed to meet specified performance from 0°C
to 70°C and is designed, characterized and expected to meet these extended
temperature limits, but is not tested at –40°C and 85°C. The LT1222I is
guaranteed to meet the extended temperature limits.
Note 4: Input offset voltage is pulse tested and is exclusive of warm-up drift.
Note 5: Slew rate is measured between ±10V on an output swing of ±12V.
Note 6: FPBW = SR/2πV
P
.
Note 7: Differential Gain and Phase are tested with five amps in series.
Attenuators of 1/Gain are used as loads.
The ● denotes the specifications which apply over the temperature range 0°C ≤ T
A
≤ 70°C, otherwise specifications are at T
A
= 25°C.
V
S
= ±15V, V
CM
= 0V, unless otherwise specified.
The ● denotes the specifications which apply over the temperature range –55°C ≤ T
A
≤ 125°C for LT1222M, –40°C ≤ T
A
≤ 85°C for
LT1222I, otherwise specifications are at T
A
= 25°C. V
S
= ±15V, V
CM
= 0V, unless otherwise specified.