Datasheet

LTM4615
4
4615fb
For more information www.linear.com/LTM4615
elecTrical characTerisTics
The l denotes the specifications which apply over the full internal
operating temperature range (Note 2), otherwise specifications are at T
A
= 25°C, V
IN
= 5V, LDO_IN = 1.2V unless otherwise noted.
Per Typical Application Figure 12.
SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS
VLDO Section
V
LDO_IN
Operating Voltage (Note 3)
l
1.14 3.5 V
I
IN(LDO_IN)
Operating Current I
OUT
= 0mA, V
OUT
= 1V, EN3 = 1.2V 1 mA
I
IN(SHDN)
Shutdown Current EN3 = 0V, LDO_IN = 1.5V 0.6 20 µA
V
BOOST3
BOOST3 Output Voltage EN3 = 1.2V 4.8 5 5.2 V
V
BOOST3(UVLO)
Undervoltage Lockout 4.3 V
V
FB3
FB3 Internal Reference Voltage 1mA ≤ I
OUT
≤ 1.5A, 1.14V ≤ V
LDO_IN
≤ 3.5V,
BOOST3 = 5V, 1V ≤ V
OUT
≤ 2.59V
l
0.397
0.395
0.4
0.4
0.404
0.405
V
V
V
LDO_OUT
Output Voltage Range 0.4 2.6 V
V
DO
Dropout Voltage V
LDO_IN
= 1.5V, V
FB3
= 0.38V, I
OUT
= 1.5A (Note 4) 100 250 mV
LDO_RHI LDO Top Feedback Resistor 4.96 4.99 5.02 kΩ
I
OUT
Output Current V
EN3
= 1.2V
l
1.5 A
I
LIM
Output Current Limit (Note 5) 2.5 A
e
n
Output Voltage Noise Frequency = 10Hz to 1MHz, I
LOAD
= 1A 300 µRMS
V
IH_EN3
EN3 Input High Voltage 1.14V ≤ V
LDO_IN
≤ 3.5V
l
1 V
V
IL_EN3
EN3 Input Low Voltage 1.14V ≤ V
LDO_IN
≤ 3.5V 0.4 V
I
IN_EN3
EN3 Input Current –1 1 µA
V
OL_PGOOD3
PGOOD Low Voltage I
PGOOD3
= 2mA 0.1 0.4 V
PGOOD Threshold Output Threshold
Relative to V
FB3
PGOOD3 High to Low
PGOOD3 Low to High
–14
–4
–12
–3
–10
–2
%
%
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2:
The LTM4615 is tested under pulsed load conditions such that
T
J
≈ T
A
. The LTM4615E is guaranteed to meet performance specifications
over the 0°C to 125°C internal operating temperature range. Specifications
over the –40°C to 125°C internal operating temperature range are assured
by design, characterization and correlation with statistical process
controls. The LTM4615I is guaranteed to meet specifications over the full
internal operating temperature range. Note that the maximum ambient
temperature is determined by specific operating conditions in conjunction
with board layout, the rated package thermal resistance and other
environmental factors.
Note 3: Minimum operating voltage required for regulation is:
V
IN
≥ V
OUT(MIN)
+ V
DROPOUT
Note 4: Dropout voltage is the minimum input to output differential needed
to maintain regulation at a specified output current. In dropout the output
voltage will be equal to V
IN
– V
DROPOUT
.
Note 5: The LTM4615 has overtemperature protection that is intended
to protect the device during momentary overload conditions. Junction
temperatures will exceed 125°C when overtemperature is activated.
Continuous overtemperature activation can impair long-term reliability.
Note 6: See output current derating curves for different V
IN
, V
OUT
and T
A
.