User Manual
Table Of Contents
- Helix LT 2.10 Owner's Manual
- Contents
- Welcome to Helix LT
- Quick Start
- Setting Proper Output Levels
- Selecting Presets and Setlists
- Preset Footswitch Mode
- Stomp Footswitch Mode
- Snapshot Footswitch Mode
- Looper Footswitch Mode
- Pedal Edit Mode
- Selecting Blocks/Adjusting Parameters
- Bypassing a Block
- Choosing a Block's Model
- Choosing an Input
- Choosing an Output
- Moving Blocks
- Copying and Pasting a Block
- Clearing a Block
- Clearing All Blocks
- Saving/Naming a Preset
- Serial vs. Parallel Routing
- Removing Parallel Path B
- Moving Split & Merge Blocks for More Parallel Routings
- Dynamic DSP
- Block Order and Stereo Imaging
- What is Variax?
- The Blocks
- Tuner
- Snapshots
- Bypass Assign
- Controller Assign
- Command Center
- Global EQ
- Global Settings
- USB Audio
- MIDI
48
Bank/Prog
Knob Parameter Description
2 MIDI Ch
Sets the Bank/Program message's MIDI channel (1-16).
When set to "Base," Helix LT follows the Global MIDI chan-
nel, which is set from the "Global Settings > MIDI/Tempo"
page.
3
Bank
CC00
SetstheCC#00(BankMSB)value.Select"O"ifthereceiv-
ing device shouldn't respond to Bank MSB.
4 Bank CC32
SetstheCC#32(BankLSB)value.Select"O"ifthereceiv-
ing device shouldn't respond to Bank LSB.
5 Program
Sets the Program Change (PC) value. Select "O" if you
only want to send a Bank MSB and/or Bank LSB message.
Note On
Knob Parameter Description
2 MIDI Ch
Sets the note's MIDI channel (1-16). When set to "Base,"
Helix LT follows the Global MIDI channel, which is set from
the "Global Settings > MIDI/Tempo" page.
3 Note
Sets the MIDI note value (C-1 ~ G9). Middle C is C3.
4 Velocity
Sets the MIDI note's velocity (0-127).
5 Note O
Determines whether the MIDI note sustains until pressing
the switch again (Latching) or sustains only while the switch
is held (Momentary).
MMC (MIDI Machine Control)
Knob Parameter Description
2 Message
Determines the message type.
Ext Amp
Knob Parameter Description
2 Select
Determines the Ext Amp connection [1 (Tip-to-sleeve), 2
(Ring-to-sleeve), or both] for switching an external amp's
channel, reverb, or other functions. Only works when
"Global Settings > Preferences" > EXP 2/EXT AMP is set
to "EXT AMP."
IMPORTANT!ConnectEXTAMP1/2onlytoampliersthatutilize"short-
to-sleeve" footswitch inputs. Connecting to any other sort of input could
cause permanent damage to both your amp and Helix LT! If you're not sure
if your amp has short-to-sleeve inputs, contact the manufacturer.
IMPORTANT! Your ability to control external amp channel and/or reverb
switching with the Helix LT device has been tested with many popular amps
and heads. Unfortunately this does not guarantee compatibility with all
products. Note that, depending on the circuitry of the channel switching
jack in the guitar amp used, the EXT Amp function may not operate as
expected.
NOTE: When an Ext Amp command is assigned to Instant 1-6, the connec-
tion determined by Knob 2 (Select) is made when the preset is loaded. When
an Ext Amp command is assigned to a footswitch, the footswitch's current
state (dim or lit) determines whether or not the External Amp connection is
made when the preset is loaded; when dim, no connection is made; when lit,
the connection determined by Knob 2 (Select) is made. Subsequent presses
ofthefootswitchtoggletheconnectionon(LEDlit)ando(LEDdark).