SPIDER V FAMILY SPIDER V 30 SPIDER V 60 SPIDER V 120 SPIDER V 240 SPIDER V 240HC 40-00-0454 Rev D PILOT’S GUIDE MANUEL DE PILOTAGE PILOTENHANDBUCH MANUAL DEL PILOTO パイロット・ガイド 新手指南 Pilot’s Guide also available at www.line6.com/manuals ©2016 Line 6, Inc.
SPIDER V Comparison Chart Features Amp Models SPIDER V 30 SPIDER V 60 SPIDER V 120 SPIDER V 240 SPIDER V 240HC 78 78 78 78 78 Cabinet Models 23 23 23 23 23 Effect Models 101 101 101 101 101 30 watts 60 watts 120 watts 240 watts (120 w/per side) 240 watts (120 w/per side) Amplifier Wattage Mono/Stereo Mono Mono Mono Stereo Stereo Speaker Size 1 x 8" 1 x 10" 1 x 12" 2 x 12" 2 x 4" 1 1 1 2 2 Yes Tweeter Configuration XLR Direct Outs No No Yes Yes USB Audio Inte
Overview Welcome to the SPIDER V Pilot’s Guide. This guide contains basic details of the SPIDER V amplifier’s features and functionality. The SPIDER V amplifier is the fifth generation guitar amp from the SPIDER Family. It features Line 6’s diverse quality amp modeling in compact combo and amp head form factors. Here’s an overview of some of the new features built into the SPIDER V amplifier.
Front Panel Controls 1 2 1. INPUT Jack – Plug in your guitar here. A Relay G10T* transmitter can be recharged by inserting it into the input jack. 2. AMP/FX Knobs – AMP LAYER - DRIVE is like the volume or gain knob on other amps; controls how much “dirt” or “distortion” you get in your sound. BASS, MID and TREBLE controls are customized for each Amp Model to give you optimal tone control.
Rear Panel Connections 13 14 15 16 17 18 19 13. POWER Switch – Turns the amplifier on/off. 14. AC IN – The included power cable connects here. See the rear panel markings for electrical information. 15. iPhone / iPod USB A Port – Connect an iOS device here using a standard Lightning cable to edit tones, update, playback and record audio. This port will power your device. DO NOT plug in any non-iOS device to this port. 16. USB Select Switch – Toggles between the USB-A and USB-B ports.
Changing Presets 1. Press the Home button at any time to return to the Home Screen. The Home Screen displays the preset name and location. 2. Turn the ROTARY KNOB below the LCD screen to cycle through the list of presets. Saving Presets 1. Press and hold the ROTARY KNOB until the Save Screen appears. 2. Turn the ROTARY KNOB to select characters for editing the preset name. 3. Press the ROTARY KNOB to highlight the character. 4. Turn the ROTARY KNOB to change character.
Bypass/Enable Smart FX 1. Press the FX BUTTON to select the FX Layer. 2. Turn the ROTARY KNOB to highlight which effect you wish to bypass or enable. 3. Press the ROTARY KNOB to bypass or enable the highlighted effect. 4. Press the HOME BUTTON to exit. Using the Quick Looper* To enter Quick Looper Mode, press the Loop button. To record a loop: 1. To begin recording, press the Loop button to set the loop start. 2. To stop recording and start playback, press the Loop button to set the loop end. 3.
Relay G10T Wireless Charging and Syncing* 1. Insert the Relay G10T transmitter into the INPUT JACK. SPIDER V will find and select the best available channel and charge the transmitter. 2. After a few seconds a check mark will appear on screen to show the transmitter is ready to use. Remove your Relay G10T transmitter and plug it into your guitar. 3. The battery life is also indicated on the Home Screen when the Relay G10T transmitter is detected. When showing 3 bars, the battery is full. 4.
SPIDER V 240HC 8 OHM STEREO SPEAKER OUTS USE 4Ω MONO OR 8Ω STEREO USE CLASS 2 WIRING ONLY RIGHT LEFT/MONO 4 OHM MONO SPEAKER OUTS USE 4Ω MONO OR 8Ω STEREO USE CLASS 2 WIRING ONLY RIGHT LEFT/MONO
