User Manual

7
Rear Panel
RETURN / AUX
(STEREO)
SEND
(STEREO)
FOOTSWITCH
7
/ 8
USB DC IN
POWER
FX LOOPGUITAR IN AMP OUT PHONESEXP 2
L / MONO
BAL
/ UNBAL
RIGHT
MAIN OUT
RELAY G10T
STORAGE
RELAY G10T
CHARGER
16 17 18
15
20 21 22 23 2419
15. Relay G10T Storage When not using or charging the included G10TII
wireless transmitter, insert it into this handy storage well.
16. GUITAR IN Connect your guitar or bass to the GUITAR IN jack. Connect the
included G10TII wireless transmitter here to charge its battery.
IMPORTANT!IfyouturnoPODGoWirelesswhileaG10TorG10TIIisin
the Guitar/Charge port, it will remain in sleep mode and slowly lose charge
over a week or so. Not a problem if you play POD Go every day, but a huge
bummer when you come back from vacation (which is why you should
bring POD Go Wireless on vacation with you!). While in the storage well,
the G10T/G10TII may retain its charge for a month or more, so it’s ready
to go when you are.
17. EXP 2, FOOTSWITCH 7/8 Connect an expression pedal here to adjust
a wide variety of parameters. Alternatively, one (or with a Y-cable, two) external
footswitches can be added to access additional stomps. (FS7=tip, FS8=ring). For
externalfootswitches,themomentary(unlatched)typeshouldbeused.
18. FX LOOP These stereo 1/4" in and out jacks can be used as an FX loop for
insertingexternalstompboxesbetweenspecicblocks in PODGo,orasinputs
and outputs for running 4-Cable Method rigs. See “POD Go in 4-Cable Method”.
Alternatively, the TRS Return/AUX input can act as an always-on, Aux In for
monitoringmixers,keyboards,drummachines,orMP3players.Tosetthefunction
of the Return L/R jack, see “Global Settings > Ins/Outs”.
19. MAIN OUT L/MONO, RIGHT These 1/4" outputs can accommodate either
unbalanced TS cables to connect to your guitar amp or other pedals, or balanced
TRScablestoconnecttoyourmixingconsoleorstudiomonitors.Whenconnecting
to a mono pedal or single amp, connect only the L/MONO 1/4" jack.
IMPORTANT! If the PHONES jack is connected, the MAIN OUT jacks will
always be stereo, regardless of whether or not the RIGHT out is connected.
20. AMP OUT This unbalanced output is meant to send directly to the front of your
guitaramp.Bydefault,itreectsthesameoutputastheMAINoutputs(exceptin
mono),but itcanbegloballyswitched tobetappedodirectlybeforetheCab/
IRblock. Thisway,youcansenda cab-emulatedsignaltoyourmixer(orFRFR
speaker) while simultaneously sending a non-cab-emulated signal to your guitar
amp.
21. PHONES Connect stereo headphones here; turn the VOLUME knob to adjust
volume.
IMPORTANT! Always turn the VOLUME knob down before connecting
headphones. Protect your hearing!
22. USB POD Go also functions as a multichannel, 24-bit audio interface for Mac
and Windows computers, with DI, re-amping, and MIDI functionality built in. Use of
aUSB2.0or3.0portisrequired—donotuseanexternalUSBhub.PODGocan
also record to an Apple iPad or iPhone mobile device (with optional Apple Camera
Connection Kit).
23. DC In Line 6 recommends using only the supplied DC-3h power supply. The
provided AC adapter serves as the disconnect device.
24. Power Switch When’sthelasttimeaoor-basedPODhadapowerswitch?A
long time. You’re welcome.