User Manual

38
Global Settings > Switches/Pedals
Page Knob Parameter Description
1
1 Stomp Block Sel
Determines whether pressing a Stomp mode footswitch automatically selects the assigned block for editing.
2 FS Auto Assign
DetermineswhethernewlyaddedeectsblocksareautomaticallyassignedtounusedStompmodeswitchesforblockbypass.Whensetto
“O,”youmustmanuallyassignblockstofootswitches.
3 Stomp Mode
By default, Stomp footswitch mode displays 6 stomps. You may also choose “4 Switches”, which replaces FS1 and FS4 with and
switches, so you can access preset banks and snapshots from without leaving Stomp mode.
4 Snapshot Mode
When set to “Auto Return,” POD Go returns to Preset mode after selecting a snapshot. When set to “Manual,” POD Go stays in Snapshot
mode until pressing MODE/EDIT/EXIT. When set to “Toggle,” pressing and toggles between Preset and Snapshot footswitch modes and
POD Go remembers this state even after switching to Stomp mode.
5 Up/Down Switches
When set to “Presets” or “Snapshots,” and change to PRESET / or SNAPSHOT / , where pressing either switch instantly
selectsthenext/previouspresetorsnapshot,withoutabankqueue.Thisisusefulifyou’veprogrammedaxedsetlistforyourshowand
just want to increment through presets or snapshots. SHORTCUT: At any time, press and hold both and to cycle through BANK / ,
PRESET / , and SNAPSHOT / .
2
1 EXP 2 FS7/8
DetermineswhethertheEXP2|FOOTSWITCH7/8jackactsasanExpressionPedal2input—or—adualfootswitchinputforaddingtwo
additional stomp switches.
2 EXP 1 Polarity
Ifyourexternalexpressionpedalappearstoworkbackwards—forexample,aVolumepedalblockisloudestwiththeheelallthewaydown—
set this to “Inverted.”
3 EXP 2 Polarity
4 EXP 1 Position
DetermineswhetherthePODGoexpressionpedalpositionsarerecalledpersnapshot,perpreset,orappliedglobally.IfyouwantaVolume
Pedal or Wah to maintain its position when switching presets, set this to “Global.”
5 EXP 2 Position
3
1 Switch LEDs
DetermineswhethertheStompmodefootswitches’coloredLEDringsappeardimwhenbypassed(“Dim/Lit”),orowhenbypassed(“O/Lit”).
Whenplayinginbrightsunlight,youmaywanttosettothisto“O/Lit”toincreasecontrast.
2 Tap Display
DetermineshowtheTempoisdisplayed.“LEDFlash”ashestheredTAPLED,“TempoPanel”openstheTempoPanelwhensteppingonTAP
while in Edit View, and “LED+Panel” does both.
*ForconnectinganexternalfootswitchtoaccessStomps7and8,theuseofamomentary(unlatched)typefootswitchisrecommended.
Global Settings > MIDI/Tempo
Knob Parameter Description
1 MIDI Channel
Sets the system base MIDI channel that POD Go uses for both receiving and sending MIDI communication via USB.
2 Tx/Rx MIDI PC
Determines whether POD Go transmits a Program Change (PC) message via USB when recalling presets. It also determines whether it responds to
incoming PC messages via USB.
3 Rx MIDI Clock
Determines whether POD Go responds to incoming MIDI beat clock via USB.
4 Tempo Select
Choose whether the tempo is stored and recalled with each snapshot, recalled with each preset, or is applied globally across all presets and snapshots.
5 BPM
Depending on the Knob 4 (Tempo Select) setting, this Beats Per Minute tempo value is saved per snapshot, per preset, or globally.