User Manual

37
Global Settings > Ins/Outs
Page Knob Parameter Description
1
1 Guitar In Pad
If your guitar or bass has active or really loud pickups, you may want to turn this on. There’s really no rule; use what sounds best.
2 Main Out Level
Choose“Line”whenconnectingtheMAINOUTjackstopoweredspeakersormixers;choose“Instrument”whenconnectingtostompboxesorthe
front of guitar amps. When using a single speaker or amp, connect only the LEFT/MONO 1/4" jack.
3
Amp Out
Source
Choose“MainOut”ifyouwantthePODGoAMPOUTjacktoechotheMAINOUTS(exceptinmono);choose“PreCab/IR”ifyouwanttheAMP
OUTjacktobetappedodirectlybeforetheCab/IRblock(andtherefore,wouldnotincludetheCab/IRblockoranyblocksafterit). This way, you
cansendacab-emulatedsignaltoyourpoweredspeakers(ormixer)whilesimultaneouslysendinganon-cab-emulatedsignalstraightintoyour
guitar amp.
4 FX Loop Level
DetermineswhethertheFXLOOPjacksshouldaccommodatestompboxes(“Instrument”)orlinelevelstudioracktypeprocessors(“Line”).
5 Return Type
Determines whether the signal received at the stereo RETURN/AUX jack should be used for the FX Loop block—or—act as an always-on, stereo
AuxIn(noprocessing)forjammingalongwithMP3players,drummachines,DJmixers,etc.
2 1 USB In 1/2 Trim
SetsthelevelofincomingaudiofromUSB1/2forjammingalongwithYouTube™,Spotify,yourDAW,etc.Normally,thisshouldbeleftat0.0dB.
Global Settings > Wireless
Knob Parameter Description
1 RF Channel
Sets the radio frequency channel for the POD Go Wireless RELAY system. Normally, this should be set to “Auto,” where POD Go Wireless automatically
picks the RF channel for the most reliable performance.
2 Cable Tone
PlayerswhotraditionallyuselongguitarcablesmayndthePODGoWirelessRELAYsystemtosoundtoo pristine. Cable Tone lets you replicate the
uniquetrebleroll-othatguitarcablesnaturallycreate.Choose“O”forthewidestpossiblefrequencyresponse,10feet(3meters),or30feet(9meters).
3 Wireless Gain
Sets the overall gain of the wireless guitar signal. Normally, this should be left at 0.0dB, but if your wireless signal appears notably louder or softer than
your other guitars, adjust to taste.
Global Settings > Preferences
Page Knob Parameter Description
1
1 Link Amp/Cab
Determines whether or not changing the Amp/Preamp block’s model will automatically change the Cab block’s model to match.
2 Snapshot Edits
Determineswhetherornotanyeditsmadetoasnapshot(blockon/o,parametercontrol,tempo)arerememberedwhenreturningtothat
snapshot. When set to “Recall,” any snapshot edits are recalled when jumping from snapshot to snapshot, and appear as you last left them. When
set to “Discard,” any snapshot edits are discarded when jumping from snapshot to snapshot, and appear as the preset was last saved. If you want
to save changes made to a snapshot while Snapshot Edits is set to “Discard,” press and ACTION together twice before selecting another.
3 Tempo Pitch
DetermineshowdelayrepeatssonicallybehavewhenrepeatedlypressingTAP.“Authentic”respectsthenaturalpitchuctuationsinherentwhen
changing a real delay pedal’s time knob; “Transparent” minimizes these artifacts.