® M5 Stompbox Modeler Pilot’s Handbook Manuel de pilotage Pilotenhandbuch Pilotenhandboek Manual del Piloto 取扱説明書 40-00-0292 Also available @ www.line6.
Important Safety Instructions C AU T IO N RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT REMOVE SCREWS. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THE APPLIANCE TO RAIN OR MOISTURE. CAUTION: This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of FCC Rules.
You should read these Important Safety Instructions. Keep these instructions in a safe place • • • • • • • • • • • • • • • • • • • • • Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
Rear Connections Basic Operation Growler FILTER FREQ Q 0.84HZ PITCH MIX EL SELE OD E YP PR ES CT M 1A S FOR T STOMPBOX 1. Power - Connect the included 9VDC 500mA Power Supply here to power the unit. 2. Expression Pedal - Compatible with standard expression pedals, including the Line 6 EX-1. Control effects parameters in real time by assigning them to this expression pedal input.
4. TAP - Tap tempo is available for all Delay effects, most Modulation effects, and some Filter effects. For Delay and Modulation effects turn the middle top row PARAMETER KNOB or for Filters turn the left bottom row PARAMETER KNOB all the way to max, and you’ll switch between tap tempo and regular control modes. Once you’re in tap tempo control mode, turn the knob to select one of the available note values.
Setup You can set this to “INSTANT PRESET” by turning the bottom center To access the setup pages, press and hold the TAP footswitch then press the MODEL SELECT knob. The DISPLAY should look similar to this: Prefs Presets Display DSP BYP AUTOSAVE CONTRST REL POTS LOAD PRESET V. 1.0 You can exit the setup pages at anytime by pressing the TAP button.
FACTORY RESET: There may be times when you’d like to reset your M5 to its Factory settings. You may want to recall a particular Factory preset, for example, or just get back to square one. To do a Factory Reset, first back up any presets you’d like to keep (as described above), then follow these steps. • Turn the MODEL SELECT knob until “RST FACT?” is displayed. • Press and hold ON/OFF while you press down on the MODEL SELECT knob - “Reset To Factory? Are You Sure” will be displayed.
All parameters affected by an expression pedal will show a pixel notch at the top indicating a parameter’s setting for the toe position of the pedal. You’ll also see a notch at the bottom that indicates a parameter’s setting with the expression pedal in the heel position. NOTE: In any case, the bar graph will automatically never display in the areas above the rightmost pixel or below the left-most pixel, since these are the extremes that the pedal’s parameter control are set to go to.
80 82 84 86 88 90 92 94 96 98 100 102 104 106 108 110 112 114 116 118 120 122 124 126 128 130 132 BPM 750 732 714 698 682 667 652 638 625 612 600 588 577 566 555 545 536 526 517 508 500 492 484 476 469 462 455 1/4 Note BPM To Milliseconds Conversions 1/8 Note 375 366 357 348 341 333 326 319 312 306 300 294 288 283 277 272 268 263 259 254 250 246 242 238 234 231 227 1/16 Note 187.
