® M13 Stompbox Modeler Pilot’s Handbook Manuel de pilotage Pilotenhandbuch Pilotenhandboek Manual del Piloto 取扱説明書 See www.line6.com/manuals for Advance Guide 40-00-0167 Advanced Users Guide available @ www.line6.
Important Safety Instructions CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT REMOVE SCREWS. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THE APPLIANCE TO RAIN OR MOISTURE. CAUTION: This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of FCC Rules.
You should read these Important Safety Instructions. Keep these instructions in a safe place • • • • • • • • • • • • • • • • • • • Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
Rear Connections POWER 1 2 IN 3 MIDI 4 OUT Basic Operation EXPRESSION PEDAL 1 PEDAL 2 INPUT L(MONO) RIGHT 5 6 FX RETURN L(MONO) RIGHT FX SEND L(MONO) RIGHT OUTPUT L(MONO) RIGHT 7 8 1. Cable Retainer - Wrap your power supply cable around this once or twice to prevent an accidental disconnect. 2. Power Input - Connect the included Line 6 Power Supply here. 3. Power - Switch goes up, lights come on. Switch goes down, lights go off. FX (1,2,3,4) Units - You can run up to 4 effects at once.
0 50 b # 440 REF E MUTE AUDIO Press and Hold TAP to activate the tuner (effects and looper will be disabled). Use your lower left parameter knob to set your reference frequency. Use the lower right parameter knob to select either “BYPASS AUDIO” or “MUTE AUDIO” for silent operation. Press tap again to exit the tuner. Memory Footswitches - Each FX Unit has 3 memories (A/B/C). Only one memory can be active at a time: its footswitch will be brightly lit, and colored to show the effect type.
Scenes & Scene Setup switch from one set of multiple effects to another. Bypass all FX units by stepping on the active scene footswitch. Scene Save You can run your M13 Stompbox Modeler in Scene Select Mode giving you 12 scenes, each of which is a complete pedalboard, storing all the settings of the A/B/C memories of the 3 FX Units.
Press REC/ODUB to start recording your loop. You can press REC/ODUB again to immediately end your loop and begin recording as many overdubs as you’d like, or... Press PLAY/STOP to continue the loop without recording. You can still jam over your loop. It just won’t be overdubbed into your loop. Press again to stop the loop playback. Setup Press and hold the LOOPER CONTROLS / HOLD FOR SETUP footswitch to enter the setup mode. Use the parameter knobs to adjust the settings described below.
Prefs Scenes FX Lp DSP BYP MNL SAVE REL POTS 1•2•3•4 MOMEN SCENE PRE ALL Prefs - Turn the MODEL SELECT knob to choose True Bypass or DSP Bypass. If you choose True Bypass, that will be activated when all FX Units are bypassed, the looper is not running, and nothing is connected to the external effect loop return. In that state, relays will switch your signal to an all-analog path. As usual with any relay switching system, you may hear an audible click in your audio as the relays switch.
That’s Not All Folks... Effect Copy An effect can be copied to any other memory location within a scene, or to a completly different scene. For example you can copy your effect in memory location FX Unit 1A to FX Unit 3B. To begin, select the memory location you would like to copy (the effect must be on and currently showing its parameters in your display). Press and hold the Model Select knob. Your display will be flashing.
You could also hook up like this, to put M13 Stompbox Modeler into your amp’s effect loop without using M13 Stompbox Modeler’s send/ return jacks at all: To amp input INPUT L(MONO) RIGHT FX RETURN L(MONO) RIGHT FX SEND L(MONO) RIGHT OUTPUT L(MONO) RIGHT To amp Return From amp Send These are just a few examples. Be creative! Mono / Stereo Operation Some models (like Stereo Delay) provide stereo operation.
