Wireless Projector Server User Manual English LINDY No’s. 32498, 32499 www.lindy.
Wireless Projector Server User Manual 1. Introduction Thank you for purchasing the LINDY Wireless Projector Server. This innovative product allows you to connect to your projector for presentations via a Wireless LAN or Ethernet network. The LINDY Wireless Projector Server features both an IEEE 802.11g 54Mbps WLAN and a 10/100Mb Ethernet LAN connection for maximum versatility. This manual refers throughout to the non audio version. The audio version (No.
Wireless Projector Server User Manual 2. Overview Front Panel LAN LED WLAN LED Power LED Rear Panel Power Switch Power Socket VGA Connector External Antenna RJ-45 Port Reset to Default Button 3. Installation 3.1 Connect the power cable to the power socket on the rear of the unit 3.2 Connect the VGA cable from your Projector to the VGA connector on the rear panel 3.3 Turn on your projector 3.
Wireless Projector Server User Manual 4 Setup 4.1 The Projector Server is ready for use when you see the picture below 4.2 Make sure your PC WLAN card is enabled in “network connections” in the Windows control panel 4.3 To connect your PC to the Projector Server, view your available wireless networks in the Windows Control Panel and double click the WPS option 4.4 Open a browser and enter the default IP address 192.168.100.
Wireless Projector Server User Manual 4.5 When you have successfully logged in to the Projector Server you will see the screen below 4.6 Click Download on the left hand side and then click the Download box. You do not need to put a password in the box. The box below will appear, click Run and follow the on screen instructions 4.
Wireless Projector Server User Manual 4.8 Enter the LOGIN CODE from the projector screen to start sending the display signal 4.
Wireless Projector Server User Manual 5 Client Utility 5.2 Opening the Application 5.2.1 Double click the icon on your desktop to execute the program: 5.2.1 The program will start to search for the Projector Server automatically: 5.2.3 When the program finds the Projector Server, the login screen will appear. Enter the Login Code shown on the Projector Server screen. If there are multiple Projector Servers in range, a list of the available connections will appear.
Wireless Projector Server User Manual This icon blinks when communicating Minimize the program Exit the program 5.3.1 Button Function – Video mode Start/Pause projecting Stop projecting Open folder Mute & volume slider control Timeline slider control Server Login Code Function menu This icon blinks when communicating Minimize the program Exit the program 6 Web Management 6.1 Home Page 6.1.1 Make sure your PC has connected to the box successfully 6.1.
Wireless Projector Server User Manual 6.2 Conference Control This function allows you to host a meeting using the WLAN connection and without the need for constantly swapping a patch cable. 6.2.1 Once logged in, select the Conference Control function 6.2.2 Enter the password (the default password and username is “trainer”) and then press Login 6.2.3 After you have logged in successfully, you will see a list of users connected to the Projector Server 6.2.
Wireless Projector Server User Manual 6.3 Login Web Admin Click Admin and then enter the password (admin) to login to the system status page: 6.4 System Status Selecting System Status, shows the current system status Model Name: Product model name Versions: 1. Firmware version no.: Product firmware version number Network Status: 1. IP address 2. Subnet Mask address 3. Default Gateway address 4. Wireless Mac address 5. Wire Mac address Connection Status: 1.
Wireless Projector Server User Manual 6.5 Operating Mode • • • IP Setup IP Address: The default value is 192.168.100.10 Subnet Mask: The default value is 255.255.255.0 Default Gateway: 192.168.100.10 • • DHCP Server Setup – Can be Auto or Disabled Start IP: The starting IP address of the DHCP Server End IP: The ending IP address of the DHCP Server • • • • • • • 6.
Wireless Projector Server • • • • • 6.7 User Manual Resolution: Default resolution is 1024 x 768 Colour Depth: Based on the settings on your PC Screen Refresh Rate: This is VGA output refresh rate, either 60 Hz and 70Hz Apply: Confirm and Save modifications Cancel: Cancel all the modifications Change Passwords 6.7.1 Enter New Password: Enter a new password for each category 6.7.2 Confirm New Password: Confirm the new password 6.7.3 Apply: To confirm and save modifications 6.
Wireless Projector Server User Manual 6.8.4 The Projector Server will now restore to Factory Default Settings 6.9 Firmware Upgrade 6.9.1 Download the latest version of the Firmware from www.lindy.com 6.9.2 Save the downloaded Firmware a suitable location on your PC 6.9.3 Click Browse to search for the downloaded file 6.9.4 Click Upgrade to start 6.9.
Wireless Projector Server User Manual 6.9.7 Click OK to restart the projector server 7 Wall Mount Instructions 8 Troubleshooting Q1. Can I use the old client utility software after a firmware upgrade? A: After the firmware upgrade is complete, we recommend you download the Client utility software from the Projector Server to replace the previous version. This will resolve any incompatibility issues Q2.
CE/FCC CE Statement This device complies with the European Regulations for Electromagnetic Compatibility (EMC) of the European Union and it is equipped with the CE mark. This unit has to be used with high quality shielded connection cables. Only if these high quality shielded cables are used it can be sure that the EMC compatibility is not adversely influenced.
Recycling Information WEEE (Waste of Electrical and Electronic Equipment), Recycling of Electronic Products United Kingdom In 2006 the European Union introduced regulations (WEEE) for the collection and recycling of all waste electrical and electronic equipment. It is no longer allowable to simply throw away electrical and electronic equipment. Instead, these products must enter the recycling process.
