Table of Contents Introduction Instrument Cluster 4 12 Warning lights and chimes Gauges Message center 12 17 18 Entertainment Systems 35 MyLincoln Touch™ system 35 Climate Controls Automatic temperature control Touchscreen features Rear window defroster Lights Headlamps Turn signal control Bulb replacement Driver Controls Windshield wiper/washer control Steering wheel adjustment Power windows Mirrors Speed control Adaptive cruise control 36 36 39 42 44 44 49 51 57 57 59 63 65 67 69 Locks and S
Table of Contents Seating and Safety Restraints Seating Safety restraints Airbags Child restraints Tires, Wheels and Loading Tire information Tire inflation Tire Pressure Monitoring System (TPMS) Vehicle loading Trailer towing Recreational towing Driving Starting Brakes AdvanceTrac威 Transmission operation Reverse sensing system Rear-view camera system Roadside Emergencies Getting roadside assistance Hazard flasher control Fuel pump shut-off Fuses and relays Changing tires Wheel lug nut torque Jump starti
Table of Contents Maintenance and Specifications Engine compartment Engine oil Battery Engine coolant Fuel information Air filter(s) Part numbers Maintenance product specifications and capacities Engine data 294 296 298 301 304 309 324 328 329 332 Accessories 335 Ford Extended Service Plan 337 Scheduled Maintenance Guide 341 Normal scheduled maintenance and log Index 347 361 All rights reserved.
Introduction CONGRATULATIONS Congratulations on acquiring your new Lincoln. Please take the time to get well acquainted with your vehicle by reading this handbook. The more you know and understand about your vehicle, the greater the safety and pleasure you will derive from driving it. For more information on Ford Motor Company and its products visit the following website: • In the United States: www.ford.com • In Canada: www.ford.ca • In Mexico: www.ford.com.mx • In Australia: www.ford.com.
Introduction Protecting the environment We must all play our part in protecting the environment. Correct vehicle usage and the authorized disposal of waste, cleaning and lubrication materials are significant steps towards this aim. Information in this respect is highlighted in this guide with the tree symbol.
Introduction Special instructions For your added safety, your vehicle is fitted with sophisticated electronic controls. WARNING: Please read the section Airbag Supplemental Restraint System (SRS) in the Seating and Safety Restraints chapter. Failure to follow the specific warnings and instructions could result in personal injury. WARNING: Front seat mounted rear-facing child or infant seats should NEVER be placed in front of an active passenger airbag.
Introduction authorized service facilities, and that the diagnostic information may be used for any purpose. See your SYNC威 supplement for more information. Event Data Recording This vehicle is equipped with an event data recorder (EDR). The main purpose of an EDR is to record, in certain crash or near crash-like situations, such as an airbag deployment or hitting a road obstacle; this data will assist in understanding how a vehicle’s systems performed.
Introduction To read data recorded by an EDR, special equipment is required, and access to the vehicle or the EDR is needed. In addition to the vehicle manufacturer, other parties, such as law enforcement, that have such special equipment, can read the information if they have access to the vehicle or the EDR.
Introduction CELL PHONE USE The use of Mobile Communications Equipment has become increasingly important in the conduct of business and personal affairs. However, drivers must not compromise their own or others’ safety when using such equipment. Mobile Communications can enhance personal safety and security when appropriately used, particularly in emergency situations. Safety must be paramount when using mobile communications equipment to avoid negating these benefits.
Introduction These are some of the symbols you may see on your vehicle.
Introduction Vehicle Symbol Glossary Power Windows Front/Rear Power Window Lockout Child Safety Door Lock/Unlock Interior Luggage Compartment Release Panic Alarm Engine Oil Engine Coolant Engine Coolant Temperature Do Not Open When Hot Battery Avoid Smoking, Flames, or Sparks Battery Acid Explosive Gas Fan Warning Power Steering Fluid Maintain Correct Fluid Level Service Engine Soon Engine Air Filter Passenger Compartment Air Filter Jack Check Fuel Cap Low Tire Pressure Warning MAX MIN
Instrument Cluster WARNING LIGHTS AND CHIMES Instrument cluster with standard measure shown; metric similar 100 120 140 80 60 180 200 160 220 140 120 100 80 40 60 40 20 0 km/h 20 MPH 0 OFF Warning lights can alert you to a vehicle condition that may become serious enough to cause extensive repairs. A warning light may illuminate when a problem exists with one of your vehicle’s functions. Many lights will illuminate when you start your vehicle to make sure the bulbs work.
Instrument Cluster Solid illumination after the engine is started indicates the on-board diagnostics system (OBD-II) has detected a malfunction. Refer to On-board diagnostics (OBD-II) in the Maintenance and Specifications chapter. If the light is blinking, engine misfire is occurring which could damage your catalytic converter. Drive in a moderate fashion (avoid heavy acceleration and deceleration) and contact your authorized dealer as soon as possible.
Instrument Cluster Anti-lock brake system: If the ABS light stays illuminated or ABS continues to flash, a malfunction has been detected. Contact your authorized dealer as soon as possible. Normal braking is still functional unless the brake warning light also is illuminated. Airbag readiness: If this light fails to illuminate when the ignition is turned on, continues to flash or remains on, contact your authorized dealer as soon as possible.
Instrument Cluster AdvanceTrac威 off light: Illuminates when AdvanceTrac威/traction control has been disabled by the driver. Refer to OFF the Driving chapter for more information. Low tire pressure warning: Illuminates when your tire pressure is low. If the light remains on at start up or while driving, the tire pressure should be checked. Refer to Inflating your tires in the Tires, Wheels and Loading chapter.
Instrument Cluster Door ajar (RTT): Displays when the ignition is on and any door is open. Tailgate ajar (RTT): Displays when the ignition is on and the trunk is open. Low washer fluid (RTT): Illuminates when the windshield washer fluid is low. Turn signal: Illuminates when the left or right turn signal or the hazard lights are turned on. If the indicators flash faster, check for a burned out bulb. High beams: Illuminates when the high beam headlamps are turned on.
Instrument Cluster Grade assist (RTT): Illuminates when the grade assist is turned on. Headlamps on warning chime: Sounds when the headlamps or parking lamps are on, the ignition is off (the key is not in the ignition) and the driver’s door is opened. Parking brake on chime: Sounds when the parking brake is left on and the vehicle is driven. If the warning stays on after the park brake is off, contact your authorized dealer as soon as possible. GAUGES Shown in standard measure. Metric similar.
Instrument Cluster MESSAGE CENTER WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that drivers use extreme caution when using any device or feature that may take their focus off the road. Your primary responsibility is the safe operation of the vehicle. We recommend against the use of any handheld device while driving and that you comply with all applicable laws.
Instrument Cluster Press the OK button to select highlighted options and confirm choices/messages. Main menu From the main menu screen you can choose the following: • Display Mode • Trip 1 & 2 • Fuel Economy • Settings • Information Scroll up/down to highlight one of the options, then press the right arrow key or OK to enter into that menu option. Gauge mode Press the right arrow on the left steering wheel mounted button when display mode is selected.
Instrument Cluster Full analog tachometer + Fuel gauge F E 01234.5mii Full analog tachometer + Fuel gauge + Engine coolant temperature gauge F H E C F 6 01234.5mi Intelligent all-wheel drive (AWD) (if equipped) + fuel gauge Shown with vertical bar tachometer enabled 4 RPM + 1000 2 E 0 01234.5mi Select-Shift Automatic™ transmission (SST) Select-Shift tnsmission allows you to manually shift gears.
Instrument Cluster The selected gear will be displayed at the bottom of the vertical bar tachometer (if selected). 6 F 4 RPM + 1000 2 E 0 The selected gear will be displayed within the full analog tachometer (if selected). Trip 1 & 2 Press the right arrow on the left steering wheel mounted button when trip 1 & 2 is selected. The boxes in the upper right corner of the screen indicate that there are multiple screens that you can navigate through.
Instrument Cluster • Average fuel economy — shows the average fuel economy for a given trip. • Estimated amount of fuel consumed — shows the amount of fuel used for a given trip. • Elapsed trip time — timer stops when the vehicle is turned off and restarts when the vehicle is restarted. Standard trip mode Shown with vertical bar tachometer 6 F enabled 139.5 mi 4 RPM + 1000 00:58:44 2 E 01234.
Instrument Cluster Fuel Economy Press the right arrow on the left steering wheel mounted button when fuel economy is selected. The boxes in the upper right corner of the screen indicate that there are multiple screens that you can navigate through. Each press of the right arrow will navigate to the next screen until the last screen is reached.
Instrument Cluster To determine your average highway fuel economy, do the following: 1. Drive the vehicle at least 5 miles (8 km) with the speed control system engaged to display a stabilized average. 2. Record the highway fuel economy for future reference. It is important to press RESET in order to reset the function after setting the speed control to get accurate highway fuel economy readings. For more information refer to Essentials of good fuel economy in the Maintenance and Specifications chapter.
Instrument Cluster Autolamp Delay Easy Entry/Exit Fuel Locks Menu Control Oil Life Reset Power Liftgate Remote Start Windows Wipers Vehicle Off, 10 / 20 (default setting) / 30 / 60 / 90 / 120 / 180 seconds On (default on key cycle) / Off DTE Calculation Normal, Towing Long Term Econ Hold OK to Reset...
Instrument Cluster Create MyKey Traction Control Speed Warning Max Speed Volume Limiter Clear MyKeys *MyKey Press and hold OK to create MyKey Always On / User Selectable Off, 65 mph (105 km/h), 55 mph (89 km/h), 45 mph (72 km/h) Set to 80 MPH (130 km/h) / Off On / Off Hold OK to Clear MyKeys *Some MyKey items will only appear if a MyKey is set.
Instrument Cluster System Check* Oil Life Wash Fluid Doors Liftgate B lind spot Cross Traffic Brakes Fuel (distance to empty) *Some items will only display during a system check if a problem has been detected. If an issue exists on one of the monitored systems, the message center will display the number of warnings that need immediate attention in red and the number of informational warnings will be listed in amber.
Instrument Cluster LIFTGATE AJAR — Displayed when the liftgate is not completely closed. PASSENGER DOOR AJAR — Displayed when the passenger door is not completely closed. REAR LEFT DOOR AJAR — Displayed when the rear left door is not completely closed. RIGHT REAR DOOR AJAR — Displayed when the rear right door is not completely closed. CHECK FUEL FILL INLET — Displayed when the fuel fill inlet may not be properly closed. Refer to Easy Fuel™ “no cap” fuel system in the Maintenance and Specifications chapter.
Instrument Cluster engine oil in the Maintenance and Specifications chapter. If the warning stays on or continues to come on, contact your authorized dealer as soon as possible. OIL CHANGE REQUIRED — Displayed when the oil life left reaches 0%. WASHER FLUID LEVEL LOW — Indicates the washer fluid reservoir is less than one quarter full. Check the washer fluid level. Refer to Windshield washer fluid in the Maintenance and Specifications chapter.
Instrument Cluster message after driving a short distance with the road tire re-installed or after the system is allowed to cool. CHECK AWD — Displayed in conjunction with the Throttle Control/Transmission/AWD light when the AWD system is not operating properly. If the warning stays on or continues to come on, contact your authorized dealer as soon as possible. FOR HILL DESCENT REDUCE SPEED 20 MPH OR LESS (if equipped) — Displayed when hill descent speed exceeds 20 MPH.
Instrument Cluster COULD NOT PROGRAM KEY — Displayed when an attempt is made to program a spare key using two existing MyKeys. Refer to MyKey™ in the Locks and Security chapter for more information. KEY PROGRAMMED 3 KEYS TOTAL — Displayed during spare key programming, when a third Intelligent Access Key is programmed to the system. KEY PROGRAMMED 4 KEYS TOTAL — Displayed during spare key programming, when a fourth Intelligent Access Key is programmed to the system.
Instrument Cluster STARTING SYSTEM FAULT — This message is displayed when there is a problem with your vehicle’s starting security system; your vehicle will not be able to start. See your authorized dealer for service. VEHICLE AT TOP SPEED OF MYKEY SETTING — Displayed when a MyKey™ is in use and the MyKey speed limit is on and the vehicle speed is 80 mph (130 km/h). Refer to MyKey™ in the Locks and Security chapter for more information.
Instrument Cluster BLINDSPOT NOT AVAILABLE SENSOR BLOCKED SEE MANUAL(if equipped) — Displayed when the blind spot information system/cross traffic alert system sensors are blocked. See Blind Spot Information System (BLIS威) with Cross Traffic Alert in the Driving chapter. BLIND SPOT SYSTEM FAULT (if equipped) — Displayed when a fault with the blind spot information system has occurred. Contact your authorized dealer as soon as possible.
Instrument Cluster TO STOP ALARM START VEHICLE — Displayed when the perimeter alarm system is armed and the vehicle is entered using the key on the driver’s side door. In order to prevent the perimeter alarm system from triggering, the ignition must be turned to start or on before the 12 second chime expires. See Perimeter alarm system in the Locks and security chapter. TRAILER SWAY REDUCE SPEED (if equipped)— Displayed when the trailer sway control has detected trailer sway.
Entertainment Systems MYLINCOLN TOUCH™ WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that drivers use extreme caution when using any device or feature that may take their focus off the road. Your primary responsibility is the safe operation of the vehicle. We recommend against the use of any handheld device while driving and that you comply with all applicable laws.
Climate Controls DUAL AUTOMATIC TEMPERATURE CONTROL (DATC) SYSTEM WITH MYTEMP 10 1 9 2 8 7 6 5 4 3 Note: Your climate control system is touch sensitive. You need only lightly touch the control graphic to activate the feature. Note: Your vehicle is also equipped with touchscreen climate control features. To access, press the lower right corner of the touchscreen. Refer to Touchscreen features later in this section for more information.
Climate Controls economical and efficient. Recirculated air may also help reduce undesirable odors from entering the vehicle. Touch MAX A/C again for normal A/C operation. 4. A/C control: Touch to activate/deactivate air conditioning. Use with recirculated air to improve cooling performance and efficiency. Engages automatically in MAX A/C, (defrost) and (floor/defrost). 5. (Power): Touch to activate/deactivate the climate control system.
Climate Controls Operating tips • To reduce fog build-up on the windshield during humid weather, (defrost) or (floor/defrost). select • To reduce humidity build-up inside the vehicle, do not drive with the (recirculated air) engaged and A/C off. system off or with • Do not put objects under the front seats that will interfere with the airflow to the back seats. • Remove any snow, ice or leaves from the air intake area at the base of the windshield.
Climate Controls Touchscreen features Press the lower right corner on the touchscreen to access these features. 1 11 2 3 10 9 8 7 6 5 4 (Power): Press to activate/deactivate the climate control system. 1. When the system is off, outside air is prevented from entering the vehicle through the vents. 2. Passenger settings: • Press DUAL to turn on passenger side temperature control. • Press the red arrow to increase the temperature and press the blue arrow to decrease the temperature.
Climate Controls 5. MAX A/C: Press to distribute recirculated air through the instrument panel vents to cool the vehicle. This is more economical and efficient than normal A/C mode. Recirculated air may also help reduce undesirable odors from entering the vehicle. Press again for normal A/C operation. 6. A/C: Press to activate/deactivate air conditioning. Use with recirculated air to improve cooling performance and efficiency. Engages (defrost) and (floor/defrost). automatically in MAX A/C, 7.
Climate Controls • Press to control the heated seat. Refer to Heated and cooled seats in the Seat and Safety Restraints chapter. to control the cooled seat. Refer to Heated and cooled • Press seats in the Seat and Safety Restraints chapter. • Press and hold MyTemp to select a temperature you would like the vehicle to remember and maintain for you. (heated steering wheel) to activate your heated steering • Press wheel (if equipped).
Climate Controls *Note: If you have said “Temperature”, you can then say any of the following commands: • High • Low • <15.5–29.5> degrees • <60–85> degrees For more information on your touchscreen system, refer to the MyFord Touch™ / MyLincoln Touch™ supplement. REAR WINDOW DEFROSTER R The rear defroster control is located on the climate control panel and works to clear the rear window of fog and thin ice. The engine must be running to operate the rear window defroster.
Climate Controls Automatic climate control For hot weather conditions: • The interior cabin will be cooled to 72°F (22°C). • The cooled seats (if equipped) will be set to high. For cold weather conditions: • The interior cabin will be heated to 72°F (22°C). • The heated seats (if equipped) will be set to high. • Rear defrost/heated mirrors (if equipped) will be activated.
Lights HEADLAMP CONTROL Turns the lamps off. Turns on the parking lamps, instrument panel lamps, license plate lamps and tail lamps. A Turns the headlamps on. Adaptive headlamps (if equipped) The headlamp beams move in the same direction as the steering wheel which provides more visibility when driving around curves. • Without adaptive headlamps (1) • With adaptive headlamps (2) Note: The system has a power-up movement check feature.
Lights Autolamp control The autolamp system provides light sensitive automatic on-off control of the exterior lights normally controlled by the headlamp control. • To turn autolamps on, rotate the . control to A • To turn autolamps off, rotate the control from the autolamp position. The autolamp system also keeps the lights on for a predetermined amount of time after the ignition switch is turned to off.
Lights Fog lamp control The fog lamps can be turned on when the headlamp control is in , , or positions the and the high beams are not turned on. Press the top of the control, located on the instrument panel, to activate the fog lamps. The fog lamp indicator will illuminate when the fog lamps are on. Press the fog lamp control again to deactivate the fog lamps. High beams Pull the lever fully (to second detent) to activate. Pull the lever again to deactivate.
Lights WARNING: Always remember to turn on your headlamps at dusk or during inclement weather. The Daytime Running Lamp (DRL) system does not activate the tail lamps and generally may not provide adequate lighting during these conditions. Failure to activate your headlamps under these conditions may result in a collision. PANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel and all applicable lit components in the vehicle during headlamp and parking lamp operation.
Lights Vertical aim adjustment 1. Park the vehicle directly in front of a wall or screen on a level surface, approximately 25 feet (7.6 meters) away. • (1) 8 feet (2.4 meters) • (2) Center height of lamp to ground • (3) 25 feet (7.6 meters) • (4) Horizontal reference line 2. Measure the height of the headlamp bulb center from the ground and mark an 8 foot (2.4 meter) horizontal reference line on the vertical wall or screen at this height. 3.
Lights 4. Locate the vertical adjuster on each headlamp. Using a Phillips #2 screwdriver, turn the adjuster either clockwise (to adjust down) or counterclockwise (to adjust up). The horizontal edge of the brighter light should touch the horizontal reference line. 5. Close the hood and turn off the lamps. HORIZONTAL AIM IS NOT REQUIRED FOR THIS VEHICLE AND IS NON-ADJUSTABLE. TURN SIGNAL CONTROL The turn signal lever does not mechanically lock in the upward or downward position when activated.
Lights INTERIOR LAMPS Front row map lamps (if equipped) To turn on the map lamps, press the outer edge of the clear lens. The front row map lamp lights when: • any door is opened. • the dome lamp button on the instrument panel is activated. • the remote entry controls are pressed and the ignition is off. Map/dome lamp (if equipped) The dome lamp lights when: • any door is opened. • the dome lamp button on the instrument panel is activated.
Lights BULB REPLACEMENT Lamp assembly condensation Exterior lamps are vented to accommodate normal changes in pressure. Condensation can be a natural by-product of this design. When moist air enters the lamp assembly through the vents, there is a possibility that condensation can occur when the temperature is cold. When normal condensation occurs, a thin film of mist can form on the interior of the lens. The thin mist eventually clears and exits through the vents during normal operation.
Lights Number of Trade Bulbs Number * Rear sidemarker lamp N/A LED * Stop/tail/turn lamp N/A LED Backup lamp 2 921 License plate lamp 2 C5W * High-mount brake lamp N/A LED Fog lamp (if equipped) 2 H11 Front row map lamp 2 1600XB Second row dome/reading lamp 3 211-2XB Rear courtesy lamp 1 211-2XB Visor vanity lamp 2 37 All replacement bulbs are clear in color except where noted. To replace all instrument panel lights - see your authorized dealer. * To replace these lamps - see your authorized dealer.
Lights 4. Turn the bulb holder counterclockwise and remove it. 5. Disconnect the electrical connector. WARNING: Handle a halogen headlamp bulb carefully and keep out of children’s reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hand could cause the bulb to break the next time the headlamps are operated. 6. Reverse the procedure to install the new bulb.
Lights 2. At the wheel well, remove the fasteners from the splash shield, then pull the splash shield back to gain access to the bulbs. 3. Rotate the bulb socket counterclockwise and remove from the lamp assembly. 4. Carefully pull the bulb out of the socket. 5. Reverse the procedure to install the new bulb. Replacing side marker bulbs Your vehicle is equipped with LED side marker bulbs. It is designed to last the life of the vehicle. If replacement is required, see your authorized dealer.
Lights Replacing backup lamp bulbs The backup lamp bulb is located in the lower portion of the tail lamp assembly. Follow the below steps to replace the bulb. Note: Your vehicle is equipped with a tail/stop/turn/sidemarker lamp assembly containing integral multiple light emitting diodes (LED). See your authorized dealer for the replacement LED module. 1. Make sure the headlamp switch is in the off position and then open the liftgate to expose the lamp assembly bolts. 2.
Lights Replacing license plate lamp bulbs 1. Make sure the headlamp switch is in the off position. 2. Remove the two screws and the license plate lamp assembly from the liftgate. 3. Carefully pull the bulb straight out from the lamp assembly. Install new bulb(s) in reverse order. Replacing fog lamp bulbs 1. Make sure the fog lamp switch is in the off position. 2. From underneath the vehicle, remove the splash shield and rotate the harness/bulb assembly counterclockwise, to remove from the fog lamp. 3.
Driver Controls WINDSHIELD WIPERS Windshield wiper: Rotate the end of the control away from you to increase the speed of the wipers; 2 1 rotate towards you to decrease the 0 speed of the wipers. Speed dependent wipers (if equipped): When the wiper control is set to any of the interval settings except the longest pause setting, the pause time between wiping will automatically adjust with the vehicle speed. The faster your vehicle is travelling the shorter the pause time between wipes will become.
Driver Controls Windshield washer: Press the end of the stalk: 2 • briefly: causes a single swipe of 1 0 the wipers without washer fluid. • a quick press and hold: the wipers will swipe three times with washer fluid. • a long press and hold: the wipers and washer fluid will be activated for up to ten seconds. Note: Do not operate the washer when the washer reservoir is empty. This may cause the washer pump to overheat. Check the washer fluid level frequently.
Driver Controls From either position, the control will automatically return to the 2 or O (off) position. Reverse wiper feature: The rear wiper will be automatically activated in an intermittent setting when shifting into R (Reverse) if the front wipers are activated. This feature may be enabled/disabled through the message center. Refer to Message center in the Instrument Cluster chapter. TILT/TELESCOPE STEERING WHEEL (IF EQUIPPED) To adjust the steering wheel: 1.
Driver Controls Easy entry/exit feature When the ignition is turned off, the column will move to the full up and in position if this feature is activated through the message center. Refer to Message center in the Instrument Cluster chapter. When the ignition is turned on, the column will return to the previous setting. Note: The easy entry/exit feature will prevent the steering wheel from returning to the memory position until the ignition is turned off.
Driver Controls ILLUMINATED VISOR MIRROR Lift the mirror cover to turn on the visor mirror lamp. Slide-on-rod feature The visor will slide back and forth on the rod for increased sunlight coverage. Rotate the visor towards the side window and extend it rearward for additional sunlight coverage. Note: To stow the visor back into the headliner, visor must be retracted before moving it back towards the windshield.
Driver Controls CENTER CONSOLE Your vehicle may be equipped with a variety of console features. These include: 1. Cupholders 1 2. Utility compartment with in-bin 2 power point and a removable coin holder tray (two grooves on tray slide onto tracks in main bin). 3. Rear power point 3 WARNING: Use only soft cups in the cupholder. Hard objects can injure you in a collision. AUXILIARY POWER POINT (12V DC) Power outlets are designed for accessory plugs only.
Driver Controls To have full capacity usage of your power point, the engine is required to be running to avoid unintentional discharge of the battery. To prevent the battery from being discharged: • do not use the power point longer than necessary when the engine is not running, • do not leave battery chargers, video game adapters, computers and other devices plugged in overnight or when the vehicle is parked for extended periods. Always keep the power point caps closed when not being used.
Driver Controls To operate one-touch up, pull the switch completely up to the second detent and release quickly. The window will close fully. Momentarily press the switch to any position to stop the window operation. Global open windows to begin opening the two front windows and venting Press and hold the panoramic roof (if equipped). control can then be released and the windows and panoramic • The roof will complete the opening operation.
Driver Controls Window lock The window lock feature allows only the driver and front passenger to operate the power windows. To lock out all the window controls (except for the driver and front passenger) press the right side of the control. Press the left side to restore the window controls. Accessory delay With accessory delay, the audio system, power windows and moon roof (if equipped) operate for up to 10 minutes after the ignition is turned off or until either front door is opened.
Driver Controls EXTERIOR MIRRORS Power side view mirrors WARNING: Do not adjust the mirror while the vehicle is in motion. To adjust your mirrors: 1. Rotate the control clockwise to adjust the right mirror and rotate the control counterclockwise to adjust the left mirror. 2. Move the control in the direction you wish to tilt the mirror. 3. Return to the center position to lock mirrors in place.
Driver Controls Fold-away mirrors Pull the side mirrors in carefully when driving through a narrow space, like an automatic car wash. Blind spot mirrors (if equipped) Your vehicle may be equipped with blind spot mirrors or a blind spot information system. Refer to Blind spot mirrors or Blind spot information system (BLIS威) with cross traffic alert (CTA) in the Driving chapter.
Driver Controls 2. Accelerate to the desired speed. 3. Press SET upward and release. 4. Take your foot off the accelerator pedal. 5. The indicator light on the instrument cluster will turn on. Note: • Vehicle speed may vary momentarily when driving up and down a steep hill. • If the vehicle speed increases above the set speed on a downhill, you may want to apply the brakes to reduce the speed.
Driver Controls Turning off speed control To turn off the speed control, press OFF downward or turn off the ignition. Note: When you turn off the speed control or the ignition, your speed control set speed memory is erased. ADAPTIVE CRUISE CONTROL (ACC) (IF EQUIPPED) Adaptive cruise control (ACC) is much like speed control, only this system is designed to automatically adjust your speed to maintain a proper distance between you and the vehicle in front of you in the same lane.
Driver Controls WARNING: Do not use in poor visibility, specifically fog, rain, spray or snow. Using adaptive cruise control Note: It is the drivers responsibility to stay alert, drive safely and be in control of the vehicle at all times. The controls for using your cruise control are located on the steering wheel. RES SET: Press to set a speed or to CNCL change the set speed. SET GAP RES/CNCL (Resume/cancel): ON Press to resume or cancel a set OFF speed. ON/OFF: Press to turn the system on or off.
Driver Controls Following a vehicle WARNING: When following a vehicle in front of you, the vehicle will not decelerate automatically to a stop, nor will the vehicle always decelerate quickly enough to avoid a collision without driver intervention. Always apply the brakes when necessary. Failing to do so may result in a collision, serious injury or death.
Driver Controls Setting the gap distance The distance between your vehicle and the vehicle in front of you can be decreased or increased by pressing the GAP control up or down. The selected gap will be displayed in the message center as shown by the bars in the graphic. Four gap distance settings are available. Graphic Following Following Dynamic display (bars distance distance at behavior between 60 mph vehicles) (96 km/h) 1 bar 1 second 29 yards (26 m) Sporty 2 bars 1.
Driver Controls Changing the set speed There are three ways to change the set speed: • Accelerate or brake to the desired speed and press SET upward and release. • Increase or decrease the speed by holding SET upward or downward until the desired set speed is shown on the message center. The vehicle speed will gradually change to the selected speed. • Increase or decrease the speed in increments of 1 mph (2 km/h) by briefly pressing the SET upward or downward.
Driver Controls Detection issues The radar sensor has a limited field of vision. In some situations it may not detect vehicles at all or detect a vehicle later than expected. Detection issues can occur: • When driving on a different line than the vehicle in front. • With vehicles that edge into your lane. These vehicles can only be detected once they have moved fully into your lane.
Driver Controls • There may be issues with the detection of vehicles in front when driving into and coming out of a bend or curve in the road. In these cases ACC may brake late or unexpectedly. The driver should stay alert and intervene when necessary. ACC Not Available Several conditions exist which can cause ACC to deactivate or prevent ACC from activating when requested. These conditions include: • The sensor is blocked, refer to Blocked sensor in this section.
Driver Controls Cause The surface of the radar in the grille is dirty or obstructed in some way The surface of the radar in the grille is clean but the message remains in the display Heavy rain or snow is interfering with the radar signals Swirling water, or snow or ice on the surface of the road may interfere with the radar signals Action Clean the grille surface in front of the radar or remove the object causing the obstruction Wait a short time.
Driver Controls STEERING WHEEL CONTROLS Audio control features SEEK: Press up or down to select the next/previous radio station preset, CD track or satellite radio channel (if equipped) preset MEDIA depending on which media mode you are in. SEEK MEDIA: Press repeatedly to scroll MUTE through available audio modes. MUTE: Press to silence the radio. VOL (Volume): Press up or down to increase or decrease the volume.
Driver Controls • Phone • Redundant center stack display • Favorite contacts • Climate • On • Fan speed • Temperature PANORAMIC VISTA ROOF™ AND POWER SUNSHADES (IF EQUIPPED) The panoramic Vista Roof™ and power sunshade controls are located on the overhead console. WARNING: Do not let children play with the panoramic Vista Roof™ and power sunshade or leave children unattended in the vehicle. They may seriously hurt themselves.
Driver Controls To open power sunshades and panoramic Vista Roof™: Press control to and release the open the sunshade. The front and rear sunshades open simultaneously. Note: Vista Roof™ will only open after power sunshades are completely open. Power sunshades will only close after Vista Roof™ is completely closed. control. To open the panoramic Vista Roof™ press and release the The panoramic Vista Roof™ will open to the “comfort” position. Press and release the control again to fully open.
Driver Controls HomeLink姞 Wireless Control System (if equipped) The HomeLink威 Wireless Control System, located on the driver’s visor, provides a convenient way to replace up to three hand-held transmitters with a single built-in device. This feature will learn the radio frequency codes of most transmitters to operate garage doors, entry gate operators, security systems, entry door locks, and home or office lighting.
Driver Controls 1. Position the end of your hand-held transmitter 1–3 inches (2–8 cm) away from the HomeLink威 button you wish to program (located on your visor) while keeping the indicator light in view. 2. Simultaneously press and hold both the chosen HomeLink威 and hand-held transmitter buttons until the HomeLink威 indicator light changes from a slow to a rapidly blinking light. Now you may release both the HomeLink威 and hand-held transmitter buttons.
Driver Controls Gate Operator & Canadian Programming During programming, your hand-held transmitter may automatically stop transmitting — not allowing enough time for HomeLink威 to accept the signal from the hand-held transmitter. After completing Step 1 outlined in the Programming section, replace Step 2 with the following: Note: If programming a garage door opener or gate operator, it is advised to unplug the device during the “cycling” process to prevent overheating.
Driver Controls Erasing HomeLink姞 buttons To erase the three programmed buttons (individual buttons cannot be erased): • Press and hold the two outer HomeLink威 buttons until the indicator light begins to flash-after 20 seconds. Release both buttons. Do not hold for longer that 30 seconds. HomeLink威 is now in the train (or learning) mode and can be programmed at any time beginning with Step 1 in the Programming section.
Driver Controls Position the floor mat so that the eyelet is over the pointed end of the retention post and rotate forward to lock in. Make sure that the mat does not interfere with the operation of the accelerator or the brake pedal. To remove the floor mat, reverse the installation procedure.
Driver Controls Note: Cycling the ignition prior to completely latching the liftgate could result in damage to the liftgate and/or its power components. Make sure the liftgate is fully latched before operating the vehicle. Care should be exercised in starting the engine before the liftgate is fully closed (latched). If the ignition is cycled during a liftgate power close cycle and the liftgate is 6–10 inches (15–24 cm) from being latched, the liftgate may reverse to the full open position.
Driver Controls To power open the liftgate with outside liftgate control button: 1. Unlock the liftgate with the transmitter or power door unlock control. If the intelligent access transmitter is within 3 feet (1 meter) of the liftgate, the liftgate will unlock when you press the liftgate release button. 2. To open the liftgate, press the control button located in the top of the liftgate pull cup handle. Note: For the best performance allow the power system to open the liftgate after pressing the control.
Driver Controls Obstacle detection: The power liftgate system is equipped with an obstacle detection feature. If the power liftgate is closing, the system will reverse to full open when it detects an obstacle. A chime will sound three times when an obstacle is detected as the liftgate begins to reopen. Once the obstacle is removed, the liftgate can be closed under power. If the power liftgate is opening, the system will stop and a chime will sound three times when an obstacle is detected.
Driver Controls Manual liftgate operation The liftgate cargo area is only intended for cargo, not for passengers. To open the liftgate, press the button located in the top of the liftgate pull cup handle to unlatch the liftgate, then pull on the handle. • Exercise care when opening or closing the liftgate in a garage or other enclosed area. The liftgate could be damaged against a garage door, low ceiling or wall. • Do not hang anything (bike rack, etc.) from the spoiler/glass or liftgate.
Driver Controls CARGO AREA FEATURES Cargo management system (if equipped) The cargo management system consists of storage compartments located in the floor of the rear cargo area. 1. To open, lift the release handle and the lid. 2. To close, lower the lid. Cargo net (if equipped) The cargo net secures lightweight objects in the cargo area. Attach the net to the loops and anchors provided. WARNING: This net is not designed to restrain objects during a collision.
Driver Controls Utility hook The utility hook can be used to hang small items such as grocery bags, etc. Do not hang more than 10 lb (4.5 kg) on the hook. ROOF RACK SYSTEM (IF EQUIPPED) Loads should never be placed directly on the roof panel. For proper function of the roof rack system, loads must be placed directly on crossbars affixed to the roof rack side rails. Your vehicle may be equipped with factory-installed crossbars.
Locks and Security INTELLIGENT ACCESS KEY (IA KEY) Your vehicle is equipped with two intelligent access keys which operate the power locks and the remote entry system. The IA key must be in the vehicle to activate the push button start system. The IA key also contains a removable mechanical key blade that can be used to unlock the driver door. To release the mechanical key blade, slide the release on the back of the transmitter and pull the blade out. Your IA keys are programmed to your vehicle.
Locks and Security feature. When the MyKey™ feature is enabled the user can use system check in the message center to see how many MyKeys™ and admin keys are programmed to the vehicle, and see the total distance the vehicle has been driven with the MyKey™ active. MyKey™ restricted features Standard settings – these settings cannot be changed • The audio system will be muted whenever Belt-Minder威 is activated until the safety belts are buckled.
Locks and Security MyKey™ is successfully programmed. Make sure you label it so you can distinguish it from the admin keys. Note: To program the optional settings go to Step 2 in the Programming MyKey™ optional settings section. If your vehicle is equipped with remote start, see the Using MyKey™ with remote start systems section. Note: All MyKeys™ can be cleared within the same key cycle that it was created, otherwise an admin key is required to clear the MyKey™ programming.
Locks and Security Refer to Message center in the Instrument Cluster chapter for MyKey™ system warnings displays. Using MyKey™ with remote start systems MyKey™ is not compatible with non Ford-approved aftermarket remote start systems. If you choose to install a remote start system please see your authorized dealer for a Ford-approved remote start system. The following information MAY help customers who choose to use a non Ford-approved remote start system.
Locks and Security Troubleshooting Condition Can’t create a MyKey™ Cannot program the MyKey™ optional settings Cannot clear MyKey™ Lost the only admin key Lost any key Potential Causes • Key in backup slot is the last remaining admin key (there always has to be at least one admin key). • Key in backup slot is a MyKey™. • Key is not in the backup slot. • SecuriLock威 passive anti-theft system is disabled or in unlimited mode.
Locks and Security Condition Potential Causes I accidentally • Vehicle has a non Ford-approved remote start programmed all keys system that is recognized as an admin key. Refer as MyKeys™ to the Using MyKey™ with remote start systems section to reset all MyKeys™ as admin keys. No MyKey™ • An admin intelligent access key is present. function • No MyKeys™ are programmed to the vehicle. Refer to Create a MyKey™ section.
Locks and Security POWER DOOR LOCKS • Press the doors. control to unlock all • Press the doors. control to lock all Smart unlocks The smart unlock feature is intended to prevent you from unintentionally locking your IA key inside your vehicle’s passenger compartment or rear cargo area.
Locks and Security Autolock feature The autolock feature will lock all the doors when: • all the doors are closed, • the ignition on, • you shift into any gear putting the vehicle in motion, and • the vehicle attains a speed greater than 12 mph (20 km/h). The autolock feature repeats when: • any door is opened then closed while the ignition is on and the vehicle speed is 9 mph (15 km/h) or lower, and • the vehicle then attains a speed greater than 12 mph (20 km/h).
Locks and Security 1. Turn the ignition on. 2. Press the power door unlock control on the door panel three times. 3. Turn the ignition off. 4. Press the power door unlock control on the door panel three times. 5. Turn the ignition back on. The horn will chirp one time to confirm programming mode has been entered and is active. 6. To enable/disable the autolock feature, press the unlock control, then press the lock control.
Locks and Security Note: The doors will not autounlock if the vehicle has been electronically locked before the driver door is opened. Deactivating/activating autounlock feature Your vehicle comes with the autounlock features activated; there are four methods to enable/disable this feature: • Through your authorized dealer, • by using a power door unlock/lock sequence, • using a keypad procedure, or • or by using the instrument cluster message center.
Locks and Security Keyless entry keypad autounlock enable/disable procedure 1. Turn the ignition off. 2. Close all the doors. 3. Enter factory–set 5–digit entry code. 4. Press and hold the 3 • 4. While holding the 3 • 4, press and release the 7 • 8. While still holding the 3 • 4, press and release the 7 • 8 a second time. 5. Release the 3 • 4. The user should receive a horn chirp to indicate the system has been disabled or a chirp followed by a honk to indicate the system has been enabled.
Locks and Security Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. The typical operating range for your transmitter is approximately 33 feet (10 meters). A decrease in operating range could be caused by: • weather conditions, • nearby radio towers, • structures around the vehicle, or • other vehicles parked next to your vehicle. The transmitter allows you to: • remotely unlock the vehicle doors . .
Locks and Security Your intelligent access system uses a radio frequency (RF) signal to communicate with your vehicle and authorize your vehicle to unlock when commanded (either by touching the inside of the driver or front passenger exterior door handle, the power liftgate button, or a button on the transmitter itself). If excessive RF interference is present in the area, or if your vehicle battery is low, it may be necessary to mechanically unlock your door.
Locks and Security The battery saver feature will turn off the lamps 10 minutes after the ignition is turned off. Two stage unlocking may be disabled or re-enabled by simultaneously pressing the and controls on the transmitter for four seconds (disabling two stage unlock allows all vehicle doors to unlock simultaneously). The parking lamps will illuminate twice to indicate that two-stage unlock was enabled or disabled.
Locks and Security If the liftgate stops mid-travel, it may have detected an obstacle. Check to ensure the liftgate swing zone is free from obstruction and reset the power assist by manually closing the liftgate. Normal operation can then be resumed. WARNING: Make sure the liftgate is closed to prevent exhaust fumes from being drawn into the vehicle. This will also prevent passengers and cargo from falling out.
Locks and Security 2. Within three seconds press the . 3. Repeat this procedure for transmitter if desired. Memory profiles The memory feature also coordinates with user-created profile settings utilizing the infotainment touchscreen system (if equipped). See the Creating a user profile section in the MyLincoln Touch™ supplement for more information. Replacing the battery The intelligent access key (IA key) uses one coin type three-volt lithium battery CR2032 or equivalent. To replace the battery: 1.
Locks and Security Replacing lost intelligent access keys (IA keys) If you would like to have your IA keys reprogrammed because you lost one, or would like to buy additional transmitters you can either reprogram them yourself, or take all transmitters to your authorized dealer for reprogramming. How to reprogram your intelligent access keys (IA keys) To program new IA keys yourself, refer to SecuriLock威 passive anti-theft system in this chapter.
Locks and Security • If the dome lamps were turned on using the panel dimmer control, the battery saver will shut them off 10 minutes after the ignition has been turned off. • If the courtesy lamps were turned on because one of the vehicle doors or the trunk was opened, the battery saver will shut them off 10 minutes after the ignition has been turned off. • The battery saver will shut off the headlamps 10 minutes after the ignition has been turned off.
Locks and Security The remote start system will not work if: • The ignition is on. • The alarm system is triggered. • The feature has been disabled. • The hood is not closed. • Two remote vehicle starts have already been attempted within the last hour. • The vehicle is not in P (Park). Starting the engine with remote start The remote start label on your transmitter details the engine starting procedure.
Locks and Security The ignition must be turned on and then back off or allow one hour to pass before using remote start again. Turning the engine off after using remote start • Press one time. The parking lamps will turn off. You may have to be closer to the vehicle than when starting due to ground reflection and the added noise of the running engine. You can disable or enable the remote start system through the message center. Refer to Message center in the Instrument Cluster chapter.
Locks and Security Tips: • Do not set a code that uses five of the same number. • Do not use five numbers in sequential order. • The factory set code will work even if you have set your own personal code. Erasing personal code 1. Enter the factory set 5–digit code. 2. Within five seconds, press the 1 • 2 on the keypad and release. 3. Press and hold the 1 • 2 for two seconds. This must be done within five seconds of completing Step 2.
Locks and Security SECURILOCK姞 PASSIVE ANTI-THEFT SYSTEM SecuriLock威 passive anti-theft system is an engine immobilization system. This system is designed to help prevent the engine from being started unless an intelligent access key programmed to your vehicle is used. The use of the wrong type of coded key may lead to a “no-start” condition. The message center will display: STARTING SYSTEM FAULT.
Locks and Security If your intelligent access key are lost or stolen and you don’t have an extra key, you will need to have your vehicle towed to an authorized dealer. The key codes need to be erased from your vehicle and new keys will need to be programmed. Replacing intelligent access keys can be very costly. Store an extra programmed key away from the vehicle in a safe place to help prevent any inconveniences. Please visit an authorized dealer to purchase additional spare or replacement keys.
Locks and Security been programmed to your vehicle, you cannot program anymore and the message MAX # OF KEYS LEARNED will be displayed on the message center. 7. Remove intelligent access key from utility compartment pocket and press the or control on the newly programmed intelligent access keys to exit programming mode. 8. Verify that the remote entry functions operate (lock, unlock) and that the vehicle starts with new intelligent access key.
Locks and Security After locking the doors using any of the methods above, the turn signal lamps will flash once indicating that the perimeter alarm is in the pre-armed mode and will become fully armed in 20 seconds. Note: Pressing the power door unlock control within the 20-second, pre-armed mode will disarm the system. When fully armed (after the 20 second pre-arm mode), any IA keys found inside the vehicle are disabled/inoperable and will not start the button to re-enable them. engine.
Seating and Safety Restraints FRONT SEATING WARNING: Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the event of a collision. WARNING: Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop. WARNING: Before returning the seatback to its original position, make sure that cargo or any objects are not trapped behind the seatback.
Seating and Safety Restraints To adjust the head restraint, do the following: 1. Adjust the seatback to an upright driving/riding position. 2. Raise the head restraint by pulling up on the head restraint. 3. Lower the head restraint by pressing and holding the guide sleeve adjust/release button and pushing down on the head restraint. Properly adjust the head restraint so that the top of the head restraint is even with the top of your head and positioned as close as possible to the back of your head.
Seating and Safety Restraints To remove the adjustable head restraint, do the following: 1. Pull up the head restraint until it reaches the highest adjustment position. 2. Simultaneously press and hold both the adjust/release button and the unlock/remove button, then pull up on the head restraint. To reinstall the adjustable head restraint, do the following: 1. Insert the two stems into the guide sleeve collars. 2. Push the head restraint down until it locks.
Seating and Safety Restraints WARNING: To minimize the risk of neck injury in the event of a crash, head restraints must be installed properly. Adjusting the front power seat WARNING: Never adjust the driver’s seat or seatback when the vehicle is moving. WARNING: Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop. WARNING: Always drive and ride with your seatback upright and the lap belt snug and low across the hips.
Seating and Safety Restraints Press the front or rear portion to tilt the seat. Press the control to move the seat forward, backward, up or down. Move the switch to recline the seatback forward or rearward. Using the power lumbar support The power lumbar control is located on the outboard side of the seat. Press one side of the control to adjust firmness. Press the other side of the control to adjust softness.
Seating and Safety Restraints Heated and cooled seats Heated seats WARNING: Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion, or other physical conditions, must exercise care when using the seat heater. The seat heater may cause burns even at low temperatures, especially if used for long periods of time.
Seating and Safety Restraints If the engine falls below 350 RPMs while the cooled seats are on, the feature will turn itself off and will need to be reactivated. Climate controlled seats air filter replacement The climate controlled seat system includes air filters that must be replaced periodically. Refer to the scheduled maintenance information for more information. • There is a filter located under each front seat. • The filter can be accessed from the 2nd row foot-well area.
Seating and Safety Restraints To install a filter: 1. First, position the filter in its housing making sure that the far forward end is all the way up in the housing. 2. Push in on the center of the outside edge of the filter and rotate up into the housing until it clips into position. Memory feature This system allows automatic positioning of the driver seat, power mirrors and power tilt/telescopic steering column (if equipped) to two programmable positions.
Seating and Safety Restraints Memory profiles The memory feature also coordinates with user-created profile settings utilizing the infotainment touchscreen system. See the Creating a user profile section in the MyLincoln Touch™ supplement for more information. Easy entry/exit feature This feature automatically moves the steering wheel all the way up and in and moves the driver’s seat rearward 2 in.
Seating and Safety Restraints WARNING: To prevent possible damage to the seat or safety belts, ensure that the safety belts are not buckled when moving the seat to the load floor position. 2nd row manual folding seat To fold down the rear seat, pull up on the lever on the outboard side of the seat cushion and let the seatback rotate downward into the load floor position. 2nd row EasyFold™ seatback release (if equipped) WARNING: Ensure that the seat is unoccupied when folding it down.
Seating and Safety Restraints Press and hold the control mechanism to lower the seatback. The top portion lowers the right (40%) seatback, and the bottom portion lowers the left (60%) seatback. Returning the 2nd row seatback to the upright position WARNING: Before returning the seatback to its original position, make sure that cargo or any objects are not trapped behind the seatback. After returning the seatback to its original position, pull on the seatback to ensure that the latches are engaged.
Seating and Safety Restraints Seat-mounted armrest and cupholders Your vehicle is equipped with a rear seat armrest. To fold the armrest down, release the latch located on the seatback by pressing down and pulling forward. To access the cup holders, lift up one of the slotted areas on the cover. WARNING: Use only soft cups in the cupholder. Hard objects can injure you in a collision. Returning the 2nd row armrest to the upright position Close the cover on the cup holders.
Seating and Safety Restraints Rear heated seats (if equipped) WARNING: Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion, or other physical conditions, must exercise care when using the seat heater. The seat heater may cause burns even at low temperatures, especially if used for long periods of time.
Seating and Safety Restraints SAFETY RESTRAINTS Personal Safety System™ The Personal Safety System provides an improved overall level of frontal crash protection to front seat occupants and is designed to help further reduce the risk of airbag-related injuries. The system is able to analyze different occupant conditions and crash severity before activating the appropriate safety devices to help better protect a range of occupants in a variety of frontal crash situations.
Seating and Safety Restraints longitudinal deceleration. The pretensioners are designed to activate in frontal and near-frontal collisions, and in rollovers and side collisions when the Safety Canopy威 is activated. Driver and passenger dual-stage airbag supplemental restraints The dual-stage airbags offer the capability to tailor the level of airbag inflation energy. A lower, less forceful energy level is provided for more common, moderate-severity impacts.
Seating and Safety Restraints WARNING: Always transport children 12 years old and under in the back seat and always properly use appropriate child restraints. The front passenger sensing system can automatically turn off the front passenger airbag and passenger seat-mounted side airbag.
Seating and Safety Restraints The Restraints Control Module (RCM) monitors its own internal circuits and the circuits for the airbag supplemental restraints, crash sensor(s), safety belt pretensioners, front safety belt buckle sensors, driver seat position sensor, and front passenger sensing system. In addition, the RCM also monitors the restraints warning light in the instrument cluster. A difficulty with the system is indicated by one or more of the following.
Seating and Safety Restraints WARNING: In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt. WARNING: Each seating position in your vehicle has a specific safety belt assembly which is made up of one buckle and one tongue that are designed to be used as a pair. 1) Use the shoulder belt on the outside shoulder only. Never wear the shoulder belt under the arm. 2) Never swing the safety belt around your neck over the inside shoulder.
Seating and Safety Restraints 2. To unfasten, press the release button and remove the tongue from the buckle. Restraint of pregnant women WARNING: Always ride and drive with your seatback upright and the safety belt properly fastened. The lap portion of the safety belt should fit snug and be positioned low across the hips. The shoulder portion of the safety belt should be positioned across the chest. Pregnant women should also follow this practice. See figure below.
Seating and Safety Restraints (8 km/h) or more, the combination safety belts will lock to help reduce forward movement of the driver and passengers. In addition, the retractor is designed to lock if the webbing is pulled out too quickly. If this occurs, let the belt retract slightly and pull webbing out again in a slow and controlled manner. Automatic locking mode In this mode, the shoulder belt is automatically pre-locked. The belt will still retract to remove any slack in the shoulder belt.
Seating and Safety Restraints How to disengage the automatic locking mode Disconnect the combination lap/shoulder belt and allow it to retract completely to disengage the automatic locking mode and activate the vehicle sensitive (emergency) locking mode. WARNING: After any vehicle collision, the safety belt system at all passenger seating positions must be checked by an authorized dealer to verify that the “automatic locking retractor” feature for child seats is still functioning properly.
Seating and Safety Restraints Safety belt extension assembly If the safety belt is too short when fully extended, there is an 8 inch (20 cm) safety belt extension assembly that can be added (part number 611C22). This assembly can be obtained from an authorized dealer. Use only extensions manufactured by the same supplier as the safety belt. Manufacturer identification is located at the end of the webbing on the label.
Seating and Safety Restraints Second row comfort guide The second row outboard lap/shoulder belt is equipped with a belt comfort guide. This guide is attached to the head restraint and is stored in a pocket in the seatback. It is used to adjust the comfort of the shoulder belt for smaller occupants in the outboard second row seats. To adjust the comfort guide: 1. Slip the shoulder belt into the belt guide. 2.
Seating and Safety Restraints Safety belt warning light and indicator chime The safety belt warning light illuminates in the instrument cluster and a chime sounds to remind the occupants to fasten their safety belts. Conditions of operation If... The driver’s safety belt is not buckled before the ignition switch is turned to the on position... The driver’s safety belt is buckled while the indicator light is illuminated and the warning chime is sounding...
Seating and Safety Restraints If... The driver’s and front passenger’s safety belts are buckled before the ignition switch is turned to the on position or less than 1-2 minutes have elapsed since the ignition switch has been turned to on... The driver’s or front passenger’s safety belt is not buckled when the vehicle has reached at least 3 mph (5 km/h) and 1-2 minutes have elapsed since the ignition switch has been turned to on...
Seating and Safety Restraints The following are reasons most often given for not wearing safety belts (All statistics based on U.S. data): Reasons given... Consider... “Crashes are rare 36700 crashes occur every day. The more we events” drive, the more we are exposed to “rare” events, even for good drivers. 1 in 4 of us will be seriously injured in a crash during our lifetime. “I’m not going 3 of 4 fatal crashes occur within 25 miles (40 km) far” of home.
Seating and Safety Restraints One-time disable If at any time the driver/front passenger quickly buckles then unbuckles the safety belt for that seating position, the Belt-Minder威 is disabled for the current ignition cycle. The Belt-Minder威 feature will enable during the same ignition cycle if the occupant buckles and remains buckled for approximately 30 seconds. Confirmation is not given for the one-time disable.
Seating and Safety Restraints 3. For the seating position being disabled, buckle then unbuckle the safety belt three times at a moderate speed, ending in the unbuckled state. • After Step 3, the safety belt warning light will be turned on for three seconds. 4. Within approximately seven seconds of the light turning off, buckle then unbuckle the safety belt. • This will disable the Belt-Minder威 feature for that seating position if it is currently enabled.
Seating and Safety Restraints Important supplemental restraint system precautions Airbags DO NOT inflate slowly or gently and the risk of injury from a deploying airbag is greatest close to the trim covering the airbag module. WARNING: All occupants of the vehicle, including the driver, should always properly wear their safety belts, even when an air bag supplemental restraint system (SRS) is provided.
Seating and Safety Restraints WARNING: Do not put anything on or over the airbag module. Placing objects on or over the airbag inflation area may cause those objects to be propelled by the airbag into your face and torso causing serious injury. WARNING: Do not attempt to service, repair, or modify the airbag supplemental restraint system (SRS) or its fuses. See your authorized dealer.
Seating and Safety Restraints How does the safety belt pretensioner and airbag supplemental restraint system work? The safety belt pretensioner and airbag SRS are designed to activate when the vehicle sustains longitudinal deceleration sufficient to cause the sensors to close an electrical circuit that initiates pretensioner activation and airbag inflation. The fact that the airbags did not activate in a collision does not mean that something is wrong with the system.
Seating and Safety Restraints WARNING: Several air bag system components get hot after inflation. Do not touch them after inflation. WARNING: If the air bag has deployed, the air bag will not function again and must be replaced immediately. If the air bag is not replaced, the unrepaired area will increase the risk of injury in a collision. The SRS consists of: • driver and passenger airbag modules (which include the inflators and airbags) • seat-mounted side airbags.
Seating and Safety Restraints The front passenger sensing system will disable (will not inflate) the front passenger’s frontal airbag if: • the front passenger seat is unoccupied, or has small/medium objects in the front seat. • the system determines that an infant is present in a rear-facing infant seat that is installed according to the manufacturer’s instructions.
Seating and Safety Restraints • When the front passenger sensing system enables the front passenger frontal airbag (may inflate), the passenger airbag status indicator will illuminate the ON lamp and remain illuminated. If a person of adult size is sitting in the front passenger’s seat, but the passenger airbag status indicator OFF lamp is lit, it is possible that the person isn’t sitting properly in the seat.
Seating and Safety Restraints WARNING: Sitting improperly out of position or with the seat back reclined too far can take off weight from the seat cushion and affect the decision of the front passenger sensing system, resulting in serious injury or death in a crash. Always sit upright against your seatback, with your feet on the floor.
Seating and Safety Restraints If objects are lodged and/or cargo is interfering with the seat; please take the following steps to remove the obstruction: • Pull the vehicle over. • Turn the vehicle off. • Driver and/or adult passengers should check for any objects lodged underneath the front passenger seat or cargo interfering with the seat. • Remove the obstruction(s) (if found). • Restart the vehicle.
Seating and Safety Restraints If any of these things happen, even intermittently, have the supplemental restraint system serviced at an authorized dealer immediately. Unless serviced, the system may not function properly in the event of a collision. Seat-mounted side airbag system WARNING: Do not place objects or mount equipment on or near the airbag cover on the side of the seatbacks of the front seats or in front seat areas that may come into contact with a deploying airbag.
Seating and Safety Restraints The side airbag system consists of the following: • An inflatable bag (airbag) with a gas generator concealed behind the outboard bolster of the driver and front passenger seatbacks. • The same warning light, electronic control and diagnostic unit as used for the front airbags. • The same readiness airbag light, electronic control and diagnostic unit as used for the front airbags. • Crash sensors mounted in each front door.
Seating and Safety Restraints WARNING: If the side airbag has deployed, the airbag will not function again. The side airbag system (including the seat) must be inspected and serviced by an authorized dealer. If the airbag is not replaced, the unrepaired area will increase the risk of injury in a collision. Determining if the system is operational The SRS uses a readiness light in the instrument cluster or a tone to indicate the condition of the system.
Seating and Safety Restraints Safety Canopy姞 System WARNING: Do not place objects or mount equipment on or near the headliner at the siderail that may come into contact with a deploying Safety Canopy威. Failure to follow these instructions may increase the risk of personal injury in the event of a collision. WARNING: Do not lean your head on the door. The Safety Canopy威 could injure you as it deploys from the headliner.
Seating and Safety Restraints How does the Safety Canopy姞 System work? The design and development of the Safety Canopy System included recommended testing procedures that were developed by a group of automotive safety experts known as the Side Airbag Technical Working Group. These recommended testing procedures help reduce the risk of injuries related to the deployment of side airbags (including the Safety Canopy威).
Seating and Safety Restraints The safety canopy is mounted to roof side-rail sheet metal, behind the headliner, above each row of seats. In certain lateral collisions or rollover events, the Safety Canopy System will be activated, regardless of which seats are occupied. The safety canopy is designed to inflate between the side window area and occupants to further enhance protection provided in side impact collisions and rollover events.
Seating and Safety Restraints Determining if the system is operational The SRS uses a readiness light in the instrument cluster or a tone to indicate the condition of the system. Refer to the Airbag readiness section in the Instrument Cluster chapter. Routine maintenance of the airbag is not required. Any difficulty with the system is indicated by one or more of the following: • The readiness airbag light (same light as for front airbag system) will either flash or stay lit.
Seating and Safety Restraints Important child restraint precautions WARNING: Always make sure your child is secured properly in a device that is appropriate for their height, age and weight. Child safety restraints must be purchased separately from the vehicle. Failure to follow these instructions and guidelines may result in an increased risk of serious injury or death to your child. WARNING: All children are shaped differently.
Seating and Safety Restraints Recommendations for Safety Restraints for Children Recommended Child size, height, weight, or age restraint type Infants Children weighing 40 lb (18 kg) or less Use a child safety or tod- (generally age four or younger) seat (sometimes dlers called an infant carrier, convertible seat, or toddler seat). Small Children who have outgrown or no longer Use a beltchilproperly fit in a child safety seat (gener- positioning booster dren ally children who are less than 4 feet seat.
Seating and Safety Restraints Recommendations for attaching child safety restraints for children Use any attachment method as indicated below by “X” LATCH LATCH Safety Safety Safety (lower (lower belt belt and belt Reanchors and LATCH only Child anstraint only) top (lower Weight chors Type and tether anchors top anchor and top tether tether ananchor) chor) Rear fac- Up to ing child 48 lb X X seat (21 kg) Forward Up to facing 48 lb X X X child seat (21 kg) Forward Over facing 48 lb X X child seat (21 kg) WAR
Seating and Safety Restraints WARNING: Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision, which may result in serious injury or death. WARNING: Never use pillows, books, or towels to boost a child. They can slide around and increase the likelihood of injury or death in a collision. WARNING: Always restrain an unoccupied child seat or booster seat.
Seating and Safety Restraints Follow all the safety restraint and airbag precautions that apply to adult passengers in your vehicle. If the child is the proper height, age, and weight (as specified by your child safety seat or booster manufacturer), fits the restraint and can be restrained properly, then restrain the child in the child safety seat or with the belt-positioning booster.
Seating and Safety Restraints position whenever possible. If all children cannot be seated and restrained properly in a rear seating position, properly restrain the largest child in the front seat. When installing a child safety seat with combination lap/shoulder belts: • Use the correct safety belt buckle for that seating position. • Insert the belt tongue into the proper buckle until you hear a snap and feel it latch. Make sure the tongue is securely fastened in the buckle.
Seating and Safety Restraints 2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together. 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer’s instructions. Be sure the belt webbing is not twisted. 4. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) for that seating position until you hear a snap and feel the latch engage.
Seating and Safety Restraints 5. To put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is pulled out. 6. Allow the belt to retract to remove slack. The belt will click as it retracts to indicate it is in the automatic locking mode. 7. Try to pull the belt out of the retractor to make sure the retractor is in the automatic locking mode (you should not be able to pull more belt out).
Seating and Safety Restraints 10. Before placing the child in the seat, forcibly move the seat forward and back to make sure the seat is securely held in place. To check this, grab the seat at the belt path and attempt to move it side to side and forward and back. There should be no more than 1 inch (2.5 cm) of movement for proper installation. Ford recommends checking with a NHTSA Certified Child Passenger Safety Technician (CPST) to make certain the child restraint is properly installed.
Seating and Safety Restraints Your vehicle has LATCH lower anchors for child seat installation at the seating positions marked with the child seat symbol. The LATCH anchors are located at the rear section of the rear seat between the cushion and seat back, below the locator symbols on the seat back. Follow the child seat manufacturer’s instructions to properly install a child seat with LATCH attachments. Follow the instructions on attaching child safety seats with tether straps.
Seating and Safety Restraints Use of inboard lower anchors from the outboard seating positions (center seating use) The lower anchors at the center of the second row rear seat are spaced 460 mm (18 inches) apart. The standardized spacing for LATCH lower anchors is 280 mm (11 inches) center to center. A child seat with rigid LATCH attachments cannot be installed at the center seating position.
Seating and Safety Restraints The rear seats of your vehicle are equipped with built-in tether strap anchors located behind the seats as described below. The tether anchors in your vehicle are located under the second row seat gap cover marked with tether anchor symbols (shown with title). The tether strap anchors in your vehicle are in the following positions (shown from top view): WARNING: Attach the tether strap only to the appropriate tether anchor as shown.
Seating and Safety Restraints 2. Locate the correct anchor behind the gap cover for the selected seating position. 3. Clip the tether strap to the anchor as shown. WARNING: If the tether strap is clipped incorrectly, the child safety seat may not be retained properly in the event of a collision. 4. Tighten the child safety seat tether strap according to the manufacturer’s instructions. WARNING: If the safety seat is not anchored properly, the risk of a child being injured in a collision greatly increases.
Seating and Safety Restraints both the lap and shoulder belt on children who have outgrown child safety seats, Ford Motor Company recommends use of a belt-positioning booster. Booster seats position a child so that vehicle lap/shoulder safety belts fit better. They lift the child up so that the lap belt rests low across the hips and the knees bend comfortably at the edge of the cushion, while minimizing slouching. Booster seats may also make the shoulder belt fit better and more comfortably.
Seating and Safety Restraints Types of booster seats There are generally two types of belt-positioning booster seats: backless and high back. Always use booster seats in conjunction with the vehicle lap/shoulder belt. • Backless booster seats If your backless booster seat has a removable shield, remove the shield. If a vehicle seating position has a low seat back or no head restraint, a backless booster seat may place your child’s head (as measured at the tops of the ears) above the top of the seat.
Seating and Safety Restraints Children and booster seats vary in size and shape. Choose a booster that keeps the lap belt low and snug across the hips, never up across the stomach, and lets you adjust the shoulder belt to cross the chest and rest snugly near the center of the shoulder. The drawings below compare the ideal fit (center) to a shoulder belt uncomfortably close to the neck and a shoulder belt that could slip off the shoulder.
Seating and Safety Restraints Follow all instructions provided by the manufacturer of the booster seat. WARNING: Never place, or allow a child to place, the shoulder belt under a child’s arm or behind the back because it reduces the protection for the upper part of the body and may increase the risk of injury or death in a collision. Child restraint and safety belt maintenance Inspect the vehicle safety belts and child safety seat systems periodically to make sure they work properly and are not damaged.
Tires, Wheels and Loading NOTICE TO CROSSOVER VEHICLE OWNERS Crossover vehicles handle differently than passenger cars in the various driving conditions that are encountered on streets, highways and off-road. Crossover vehicles are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed to perform satisfactorily under off-road conditions. WARNING: Crossover vehicles have a significantly higher rollover rate than other types of vehicles.
Tires, Wheels and Loading driving surfaces are relatively level, obstruction-free and otherwise similar to normal on-road driving conditions. Operating your vehicle under other than those conditions could subject the vehicle to excessive stress which might result in damage which is not covered under your warranty. For AWD vehicles, a spare tire of a different size other than the tire provided should never be used.
Tires, Wheels and Loading INFORMATION ABOUT UNIFORM TIRE QUALITY GRADING Tire Quality Grades apply to new pneumatic passenger car tires. The Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example: • Treadwear 200 Traction AA Temperature A These Tire Quality Grades are determined by standards that the United States Department of Transportation has set. Tire Quality Grades apply to new pneumatic passenger car tires.
Tires, Wheels and Loading WARNING: The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning or peak traction characteristics. Temperature A B C The temperature grades are A (the highest), B and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel.
Tires, Wheels and Loading • Extra load: A class of P-metric or Metric tires designed to carry a heavier maximum load at 41 psi [43 psi (2.9 bar) for Metric tires]. Increasing the inflation pressure beyond this pressure will not increase the tire’s load carrying capability. • kPa: Kilopascal, a metric unit of air pressure. • PSI: Pounds per square inch, a standard unit of air pressure.
Tires, Wheels and Loading WARNING: Under-inflation is the most common cause of tire failures and may result in severe tire cracking, tread separation or “blowout”, with unexpected loss of vehicle control and increased risk of injury. Under-inflation increases sidewall flexing and rolling resistance, resulting in heat buildup and internal damage to the tire. It also may result in unnecessary tire stress, irregular wear, loss of vehicle control and accidents.
Tires, Wheels and Loading Note: If you have to drive a distance to get air for your tire(s), check and record the tire pressure first and add the appropriate air pressure when you get to the pump. It is normal for tires to heat up and the air pressure inside to go up as you drive. 2. Remove the cap from the valve on one tire, then firmly press the tire gauge onto the valve and measure the pressure. 3. Add enough air to reach the recommended air pressure.
Tires, Wheels and Loading Improper or inadequate vehicle maintenance can cause tires to wear abnormally. Inspect all your tires, including the spare, frequently, and replace them if one or more of the following conditions exist: Tire wear When the tread is worn down to 1/16th of an inch (2 mm), tires must be replaced to help prevent your vehicle from skidding and hydroplaning.
Tires, Wheels and Loading U.S. DOT Tire Identification Number (TIN) Both U.S. and Canada Federal regulations require tire manufacturers to place standardized information on the sidewall of all tires. This information identifies and describes the fundamental characteristics of the tire and also provides a U.S. DOT Tire Identification Number for safety standard certification and in case of a recall. This begins with the letters “DOT” and indicates that the tire meets all federal standards.
Tires, Wheels and Loading WARNING: When mounting replacement tires and wheels, you should not exceed the maximum pressure indicated on the sidewall of the tire to set the beads without additional precautions listed below. If the beads do not seat at the maximum pressure indicated, re-lubricate and try again. When inflating the tire for mounting pressures up to 20 psi (1.
Tires, Wheels and Loading • Do not run over curbs or hit the tire against a curb when parking WARNING: If your vehicle is stuck in snow, mud, sand, etc., do not rapidly spin the tires; spinning the tires can tear the tire and cause an explosion. A tire can explode in as little as three to five seconds. WARNING: Do not spin the wheels at over 35 mph (56 km/h). The tires may fail and injure a passenger or bystander.
Tires, Wheels and Loading • Front-wheel drive (FWD)/All-wheel drive (AWD) vehicles (front tires at top of diagram) Sometimes irregular tire wear can be corrected by rotating the tires. Note: If your tires show uneven wear ask an authorized dealer to check for and correct any wheel misalignment, tire imbalance or mechanical problem involved before tire rotation. Note: Your vehicle may be equipped with a dissimilar spare tire/wheel.
Tires, Wheels and Loading Information on “P” type tires P215/65R15 95H is an example of a tire size, load index and speed rating. The definitions of these items are listed below. (Note that the tire size, load index and speed rating for your vehicle may be different from this example.) 1. P: Indicates a tire, designated by the Tire and Rim Association (T&RA), that may be used for service on cars, SUVs, minivans and light trucks.
Tires, Wheels and Loading Note: You may not find this information on all tires because it is not required by federal law. Letter rating Speed rating - mph (km/h) M 81 mph (130 km/h) N 87 mph (140 km/h) Q 99 mph (159 km/h) R 106 mph (171 km/h) S 112 mph (180 km/h) T 118 mph (190 km/h) U 124 mph (200 km/h) H 130 mph (210 km/h) V 149 mph (240 km/h) W 168 mph (270 km/h) Y 186 mph (299 km/h) Note: For tires with a maximum speed capability over 149 mph (240 km/h), tire manufacturers sometimes use the letters ZR.
Tires, Wheels and Loading 12. Treadwear, Traction and Temperature Grades • Treadwear: The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half (11⁄2) times as well on the government course as a tire graded 100. • Traction: The traction grades, from highest to lowest are AA, A, B, and C.
Tires, Wheels and Loading Additional information contained on the tire sidewall for “LT” type tires “LT” type tires have some additional information beyond those of “P” type tires; these differences are described below. Note: Tire Quality Grades do not apply to this type of tire. 1. LT: Indicates a tire, designated by the Tire and Rim Association (T&RA), that is intended for service on light trucks. 2.
Tires, Wheels and Loading Information on “T” type tires “T” type tires have some additional information beyond those of “P” type tires; these differences are described below: T145/80D16 is an example of a tire size. Note: The temporary tire size for your vehicle may be different from this example. Tire Quality Grades do not apply to this type of tire. 1.
Tires, Wheels and Loading TIRE PRESSURE MONITORING SYSTEM (TPMS) Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires.
Tires, Wheels and Loading The tire pressure monitoring system complies with part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. WARNING: The tire pressure monitoring system is NOT a substitute for manually checking tire pressure.
Tires, Wheels and Loading When your temporary spare tire is installed When one of your road tires needs to be replaced with the temporary spare, the TPMS system will continue to identify an issue to remind you that the damaged road wheel/tire needs to be repaired and put back on your vehicle. To restore the full functionality of the tire pressure monitoring system, have the damaged road wheel/tire repaired and remounted on your vehicle.
Tires, Wheels and Loading Low tire pressure warning light Flashing warning light Possible Customer action required cause Spare tire in use TPMS malfunction Your temporary spare tire is in use. Repair the damaged road wheel and re-mount it on the vehicle to restore system functionality. For a description of how the system functions under these conditions, refer to When your temporary spare tire is installed in this section.
Tires, Wheels and Loading SNOW TIRES AND CHAINS WARNING: Snow tires must be the same size, load index, speed rating as those originally provided by Ford. Use of any tire or wheel not recommended by Ford can affect the safety and performance of your vehicle, which could result in an increased risk of loss of vehicle control, vehicle rollover, personal injury and death.
Tires, Wheels and Loading VEHICLE LOADING – WITH AND WITHOUT A TRAILER This section will guide you in the proper loading of your vehicle and/or trailer, to keep your loaded vehicle weight within its design rating capability, with or without a trailer. Properly loading your vehicle will provide maximum return of vehicle design performance.
Tires, Wheels and Loading Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be found on the Tire Label on the B-Pillar or the edge of the driver’s door (vehicles exported outside the US and Canada may not have a Tire Label). Look for “THE COMBINED WEIGHT OF OCCUPANTS AND CARGO SHOULD NEVER EXCEED XXX kg OR XXX lb.” for maximum payload.
Tires, Wheels and Loading Example only: Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue load weight is also part of cargo weight. GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload.
Tires, Wheels and Loading GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Label located on the B-Pillar or the edge of the driver’s door. The total load on each axle must never exceed its GAWR. Note: For trailer towing information refer to Trailer towing found in this chapter or the RV and Trailer Towing Guide provided by your authorized dealer.
Tires, Wheels and Loading • Example only: WARNING: Exceeding the Safety Compliance Certification Label vehicle weight rating limits could result in substandard vehicle handling or performance, engine, transmission and/or structural damage, serious damage to the vehicle, loss of control and personal injury.
Tires, Wheels and Loading GCW (Gross Combined Weight) – is the weight of the loaded vehicle (GVW) plus the weight of the fully loaded trailer. GCWR (Gross Combined Weight Rating) – is the maximum allowable weight of the vehicle and the loaded trailer – including all cargo and passengers – that the vehicle can handle without risking damage. (Important: The towing vehicles’ braking system is rated for operation at GVWR, not at GCWR.
Tires, Wheels and Loading Steps for determining the correct load limit: 1. Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs.” on your vehicle’s placard. 2. Determine the combined weight of the driver and passengers that will be riding in your vehicle. 3. Subtract the combined weight of the driver and passengers from XXX kg or XXX lbs. 4. The resulting figure equals the available amount of cargo and luggage load capacity.
Tires, Wheels and Loading calculation would be: 635 kg - (2 x 99 kg) - (12 x 45 kg) = 635 - 198 540 = -103 kg. You will need to reduce the load weight by at least 240 lb. (104 kg). If you remove 3-100 lb. (45 kg) cement bags, then the load calculation would be: 1,400 - (2 x 220) - (9 x 100) = 1,400 - 440 - 900 = 60 lb. Now you have the load capacity to transport the cement and your friend home. In metric units, the calculation would be: 635 kg - (2 x 99 kg) - (9 x 45 kg) = 635 - 198 - 405 = 32 kg.
Tires, Wheels and Loading For load specification terms found on the label, refer to Vehicle loading - with and without a trailer in this chapter. Remember to figure in the tongue load of your loaded vehicle when figuring the total weight. Powertrain 3.7L 3.7L 3.7L 3.
Tires, Wheels and Loading Hitches Do not use hitches that clamp onto the vehicle’s bumper or attach to the axle. You must distribute the load in your trailer so that 10–15% of the total weight of the trailer is on the tongue. Safety chains Always connect the trailer’s safety chains to the hook retainers on the vehicle. To connect the trailer’s safety chains, cross the chains under the trailer tongue and allow slack for turning corners.
Tires, Wheels and Loading Driving while you tow When towing a trailer: • Do not drive faster than 70 mph (113 km/h) during the first 500 miles (800 km) of trailer towing and don’t make full-throttle starts. • Turn off the speed control. The speed control may shut off automatically when you are towing on long, steep grades. • Use a lower gear to eliminate excessive shifting and assist in transmission cooling. For additional information, refer to Automatic transmission operation in the Driving chapter.
Tires, Wheels and Loading RECREATIONAL TOWING Follow these guidelines for your specific powertrain combination to tow your vehicle for personal travel (such as behind a motor home or a truck). Note: Put your climate control system in recirculated air mode to prevent exhaust fumes from entering the vehicle. Refer to the Climate Controls chapter for more information. In case of roadside emergency with a disabled vehicle, please refer to Wrecker towing in the Roadside Emergencies chapter.
Driving STARTING Ignition modes 1. Off — This position shuts the engine and all electrical accessories off. Press and release the START/STOP button without applying the brake pedal when your vehicle is in accessory or on modes or when the engine is running. Note: When the vehicle is in motion, a single press and release of the START/STOP button will not switch off the engine. In order to switch off the engine while the vehicle is in motion, press and hold the START/STOP button for at least one second. 2.
Driving WARNING: Do not start your vehicle in a closed garage or in other enclosed areas. Exhaust fumes can be toxic. Always open the garage door before you start the engine. See Guarding against exhaust fumes in this chapter for more instructions. WARNING: If you smell exhaust fumes inside your vehicle, have your dealer inspect your vehicle immediately. Do not drive if you smell exhaust fumes.
Driving • Make sure the gearshift lever is in P (Park). Push button start system Your vehicle is equipped with the push button start system. You can start your vehicle by pressing the start button in combination with the brake pedal rather than using a key. The start button is located on the instrument panel to the right of the steering wheel. In order to operate the push button start system and start the vehicle, your Intelligent Access key (IA key) must be present inside the vehicle. 1.
Driving when you press the START/STOP button, it may be necessary to move your IA key to another area within the vehicle. The IA key may not be detected near the roof (between the driver or passenger sunvisor and the roof, or in the overhead console area) or in the extreme corners of the rear package tray, near your audio speakers. It is not recommended that you stow the IA key in these locations.
Driving Absence of the Intelligent Access key: Once the vehicle has started, the vehicle will remain running until being turned off by the START/STOP button, even if the IA key is no longer found in the vehicle. Whenever a door is opened and then closed while the vehicle is running, the system will search for an IA key inside the vehicle and the message center will display NO KEY DETECTED if the IA key is no longer present.
Driving WARNING: To reduce the risk of electrical shock, do not use your heater with ungrounded electrical systems or two-pronged (cheater) adapters. Prior to using the engine block heater, follow these recommendations for proper and safe operation: • For your safety, use an outdoor extension cord that is product certified by Underwriter’s Laboratory (UL) or Canadian Standards Association (CSA).
Driving How to use the engine block heater Ensure the receptacle terminals are clean and dry prior to use. To clean them, use a dry cloth. Depending on the type of factory installed equipment, your engine block heater will use .4 to 1.0 kilowatt-hours of energy per hour of use. Your factory installed block heater system does not have a thermostat; however, maximum temperature is attained after approximately three hours of operation.
Driving Brake assist The brake assist system provides full braking force during panic braking situations. It detects a rapid application of the brake pedal and uses the ABS system to achieve maximum braking pressure. Once a panic brake application is detected, the system will remain activated as long as the brake pedal is pressed or ABS is engaged. The system is deactivated by either releasing the brake pedal or coming to a complete stop.
Driving WARNING: Always set the parking brake fully and make sure that the gearshift is securely latched in P (Park). Turn the ignition to the lock position and remove the key whenever you leave the vehicle. For vehicles with the push button start system, remove the IA key whenever you leave the vehicle. The parking brake is not recommended to stop a moving vehicle. However, if the normal brakes fail, the parking brake can be used to stop your vehicle in an emergency.
Driving WARNING: Remember that even advanced technology cannot defy the laws of physics. It’s always possible to lose control of a vehicle due to inappropriate driver input for the conditions. Aggressive driving on any road condition can cause you to lose control of your vehicle increasing the risk of personal injury or property damage.
Driving When AdvanceTrac威 with RSC威 performs a normal system self-check, some drivers may notice a slight movement of the brake, and/or a rumble, grunting, or grinding noise after startup and when driving off. When an event occurs that activates AdvanceTrac威 with RSC威 you may experience the following: • A slight deceleration of the vehicle • The stability control light will flash.
Driving Electronic stability control (ESC) Electronic stability control (ESC) may enhance your vehicle’s directional stability during adverse maneuvers, for example when cornering severely or avoiding objects in the roadway. ESC operates by applying brakes to one or more of the wheels individually and, if necessary, reducing engine power if the system detects that the vehicle is about to skid or slide laterally. During ESC events the stability control light in the instrument cluster will flash.
Driving Switching off AdvanceTrac威 with RSC威 If the vehicle is stuck in snow, mud or sand, and seems to lose engine power, switching off certain features of the AdvanceTrac威 with RSC威 system may be beneficial because the wheels are allowed to spin. This will restore full engine power and will enhance momentum through the obstacle. To switch off the AdvanceTrac威 with RSC威 system, select traction control off in the message center.
Driving TRAILER SWAY CONTROL When properly equipped, trailer sway control will use the vehicle’s AdvanceTrac威 with RSC威 system to detect and help reduce trailer sway by applying brake force at individual wheels and, if necessary, by reducing engine power. Trailer sway control is only enabled above 40 mph (64 km/h). WARNING: Trailer sway control does not prevent a trailer from swaying. It mitigates the sway from increasing once it has occurred.
Driving STEERING To help prevent damage to the power steering system: • Never hold the steering wheel at its furthest turning points (until it stops) for more than a few seconds when the engine is running. • Do not operate the vehicle with a low power steering fluid level (below the MIN mark on the reservoir). • Some noise is normal during operation. If the noise is excessive, check for a low power steering fluid level before seeking service by your authorized dealer.
Driving If the fuse is not blown and the brake lamps are working properly, the following procedure will allow you to move the gearshift lever from P (Park): 1. Apply the parking brake, turn the ignition key to the off position, and remove the key. 2. Using a screwdriver (or similar tool), carefully pry off and remove the BSI access panel. 3. Locate the brake shift interlock lever in front of the shifter assembly. 4. Apply the brake pedal.
Driving WARNING: If the parking brake is fully released, but the brake warning lamp remains illuminated, the brakes may not be working properly. See your authorized dealer. AUTOMATIC TRANSMISSION OPERATION Automatic transmission adaptive learning Your transmission is equipped with an adaptive learning strategy found in the vehicle computer. This feature is designed to increase durability and provide consistent shift feel over the life of the vehicle.
Driving N (Neutral) With the gearshift lever in N (Neutral), the vehicle can be started and is free to roll. Hold the brake pedal down while in this position. D (Drive) with Overdrive The normal driving position for the best fuel economy. Transmission operates in gears one through six. M (Manual) • Provides maximum engine braking. • Will downshift to the lowest available gear for the current vehicle speed; allows for first gear when vehicle reaches slower speeds.
Driving Recommended shift speeds Upshift according to the following chart: 1 2 3 4 5 - 2 3 4 5 6 Upshifts when accelerating (recommended for best fuel economy) Shift from: 15 mph (24 km/h) 25 mph (40 km/h) 40 mph (64 km/h) 45 mph (72 km/h) 50 mph (80 km/h) The message center display in the instrument cluster will show the current selected gear you are in.
Driving Using hill start assist Hill start assist is activated automatically when the vehicle is stopped on a slope greater than five degrees. Hill start assist operates with the vehicle facing downhill if reverse gear is selected. WARNING: You must remain in the vehicle once you have activated hill start assist. Activating hill start assist 1. Press the brake pedal to bring the vehicle to a complete standstill. Keep the brake pedal pressed. 2.
Driving REVERSE SENSING SYSTEM The reverse sensing system (RSS) sounds a tone to warn the driver of obstacles near the rear bumper when the R (Reverse) is selected and the vehicle is moving at speeds less than 3 mph (5 km/h). The system is not effective at speeds above 3 mph (5 km/h) and may not detect certain angular or moving objects. WARNING: To help avoid personal injury, please read and understand the limitations of the reverse sensing system as contained in this section.
Driving The RSS detects obstacles up to six feet (two meters) from the rear bumper with a decreased coverage area at the outer corners of the bumper, (refer to the figures for approximate zone coverage areas). As you move closer to the obstacle, the rate of the tone increases. When the obstacle is less than 10 inches (25.0 cm) away, the tone will sound continuously. If the RSS detects a stationary or receding object further than 10 inches (25.
Driving REARVIEW CAMERA SYSTEM (IF EQUIPPED) The rear video camera system, located on the liftgate, provides a video image of the area behind the vehicle. It adds assistance to the driver while reversing or reverse parking the vehicle. To use the rear video camera system, place the transmission in R (Reverse). An image will display on the touchscreen display. The area displayed on the screen may vary according to the vehicle orientation and/or road condition.
Driving Objects are getting closer to your vehicle as they move from the green zone (4) to the yellow (3) or red zones (2). Use the side mirrors and rearview mirror to get better coverage on both sides and rear of the vehicle. Visual park aid alert (if equipped) Visual park aid alert allows the driver to see the area that is causing the reverse sensing system to beep.
Driving When manual zoom is enabled, only the centerline will be shown. Menu Zoom {zoom level} Rear camera delay After shifting out of R (Reverse) and into any gear other than P (Park), the image will remain until the vehicle speed reaches five mph (8 km/h). This will only occur if the rear camera delay feature is on, or until any radio button is selected. The default setting for the rear camera delay is ON. To turn this feature on or off when the vehicle is not in R (Reverse), do the following: 1.
Driving Note: If the camera system image is not clear or seems distorted, it may be covered with water droplets, snow, mud or any other substance. If this occurs, clean the camera lens before using the camera system. WARNING: The rearview camera system is a reverse aid supplement device that still requires the driver to use it in conjunction with the rearview mirror and the side mirrors for maximum coverage.
Driving Servicing • If the image comes on while the vehicle is not in R (Reverse), have the system inspected by your authorized dealer. • If the image is not clear, check if anything is covering the lens such as dirt, mud, ice, snow, etc. If the image is still not clear after cleaning, have your system inspected by your authorized dealer.
Driving Operation The radar sensor detects vehicles ahead that are moving in the same direction as your vehicle. If the radar detects that your vehicle is rapidly closing on another vehicle a red warning light will illuminate and an audible warning chime will sound. After that, if the risk of collision further increases after the warning light, the brake support prepares the brake system for rapid braking. This may be apparent to the driver. However, the system will not automatically activate the brakes.
Driving WARNING: The collision warning system’s brake support can only help reduce the speed at which a collision occurs if the driver applies the vehicle’s brakes. The brake pedal must be pressed just like for any typical braking situation. Blocked sensor If a message regarding a blocked sensor is displayed, the radar signals from the sensor, located behind a fascia cover near the driver side of the lower grille, have been obstructed.
Driving Note: If the system cannot be turned off in a MyKey™ equipped vehicle, refer to MyKey™ in the Locks and Security chapter for more information. Note: If collision warnings are perceived as being too frequent or disturbing then the warning sensitivity can be reduced, though the manufacturer recommends using the highest sensitivity setting where possible. Setting lower sensitivity would lead to fewer and later system warnings.
Driving WARNING: Objects in the blind spot mirror are closer than they appear. BLIND SPOT INFORMATION SYSTEM (BLIS姞) WITH CROSS TRAFFIC ALERT (CTA) (IF EQUIPPED) The BLIS威 is a convenience feature that aids the driver in assessing whether a vehicle is within an area on either side of the vehicle extending rearward from the outside mirrors to approximately 10 feet (3 meters) beyond the bumper. This area is referred to as the blind zone.
Driving becomes active. Afterwards, the BLIS威 remains active for all speeds including zero mph. BLIS威 is also active if the transmission is placed in N (Neutral). If the transmission is shifted out of D (Drive) or N (Neutral) the system will enter the CTA mode (see CTA operation below). Once shifted back in to D (Drive) the BLIS威 mode will activate once driven above 3 mph (5 km/h).
Driving BLIS威 False Alerts Due to the nature of radar technology, there may be certain instances when the BLIS威 will alert with no object present in the blind zone. This is known as a false alert. Some level of false alerts are normal. Circumstances that may cause a false alert are guardrails, freeway concrete walls, cyclone fencing, sharp turns around a pole or building, or coming to a stop with a vehicle directly behind but very close. False alerts are temporary and self correct.
Driving The CTA system detects vehicles approaching up to 45 feet (14 meters) away. Coverage decreases when vehicles and objects in close proximity block the CTA sensors (refer to figure for approximate zone coverage areas [sensor obstructed for vehicle on left]). Backing slowly from the parking spot in these situations helps to increase the sensor coverage and effectiveness.
Driving CTA detection limitations: Due to the nature of radar technology, there may be certain instances where vehicles entering and exiting the blind spot zones may not be detected. Below is a list of circumstances that may cause non-detection: • Debris build-up on the rear quarter panel fascias • The rear quarter panel radar beams are obstructed or partially obstructed by an adjacently parked vehicle or object.
Driving BLIS威 and/or CTA fault operation If the BLIS威 and/or CTA senses a fault on either the left or right sensor, the BLIS威 alert indicator will go on and remain on and the message center will display BLIND SPOT SYSTEM FAULT or CROSS TRAFFIC SYSTEM FAULT. For faults that may cause the associated left or right alert indicator not to illuminate, only the message center faults will occur.
Driving The following table lists possible causes and actions for this message being displayed: The surface of the radar is dirty or obstructed in some way The surface of the radar is not dirty or obstructed Heavy rainfall or heavy snowfall is interfering with the radar signals Clean the fascia area in front of the radar, either side, or remove obstruction. Drive normally in traffic for a few minutes to allow the radar to detect that it is no longer blocked.
Driving All components of the AWD system are sealed for life and require no maintenance. Note: When an AWD system fault is present, the warning CHECK AWD will display in the message center. The AWD system is not functioning correctly and defaulted to front-wheel drive. When this warning is displayed, have your vehicle serviced at an authorized dealer If your vehicle is equipped with AWD, a spare tire of a different size other than the tire provided should never be used.
Driving Under severe operating conditions, the A/C may cycle on and off to protect overheating of the engine. Basic operating principles • Drive slower in strong crosswinds which can affect the normal steering characteristics of your vehicle. • Be extremely careful when driving on pavement made slippery by loose sand, water, gravel, snow or ice.
Driving WARNING: If the parking brake is fully released, but the brake warning lamp remains illuminated, the brakes may not be working properly. See your authorized dealer. WARNING: Do not spin the wheels at over 35 mph (56 km/h). The tires may fail and injure a passenger or bystander. Emergency maneuvers • In an unavoidable emergency situation where a sudden sharp turn must be made, remember to avoid “over-driving” your vehicle (i.e.
Driving the system has cooled down, normal AWD function will return. When driving at slow speeds in deep sand under high outside temperatures, use L (Low) gear when possible. L (Low) gear operation will maximize the engine and transmission cooling capability. Under severe operating conditions, the A/C may cycle on and off to protect overheating of the engine.
Driving Management in encouraging you to help preserve our national forest and other public and private lands by “treading lightly.” Driving on hilly or sloping terrain Although natural obstacles may make it necessary to travel diagonally up or down a hill or steep incline, you should always try to drive straight up or straight down. Avoid driving crosswise or turning on steep slopes or hills. A danger lies in losing traction, slipping sideways and possibly rolling over.
Driving Avoid sudden applications of power and quick changes of direction on snow and ice. Apply the accelerator slowly and steadily when starting from a full stop. Avoid sudden braking as well. Although an AWD vehicle may accelerate better than a two-wheel drive vehicle in snow and ice, it won’t stop any faster, because as in other vehicles, braking occurs at all four wheels. Do not become overconfident as to road conditions.
Driving DRIVING THROUGH WATER If driving through deep or standing water is unavoidable, proceed very slowly especially when the depth is not known. Never drive through water that is higher than the bottom of the wheel rims (for cars) or the bottom of the hubs (for trucks). When driving through water, traction or brake capability may be limited. Also, water may enter your engine’s air intake and severely damage your engine or your vehicle may stall.
Roadside Emergencies ROADSIDE ASSISTANCE Getting roadside assistance To fully assist you should you have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program. This program is separate from the New Vehicle Limited Warranty. The service is available: • 24-hours, seven days a week • for the coverage period listed on the Roadside Assistance Card included in your Owner Guide portfolio.
Roadside Emergencies Owner Guide portfolio in the glove compartment. In Canada, the card is found in the Warranty Guide in the glove compartment. U.S. Ford, Mercury and Lincoln vehicle customers who require Roadside Assistance, call 1-800-241-3673. Canadian customers who require roadside assistance, call 1-800-665-2006. If you need to arrange roadside assistance for yourself, Ford Motor Company will reimburse a reasonable amount for towing to the nearest dealership within 35 miles (56 km).
Roadside Emergencies WARNING: Failure to inspect and if necessary repair fuel leaks after a collision may increase the risk of fire and serious injury. Ford Motor Company recommends that the fuel system be inspected by an authorized dealer after any collision. FUSES AND RELAYS Fuses If electrical components in the vehicle are not working, a fuse may have blown. Blown fuses are identified by a broken wire within 15 the fuse. Check the appropriate fuses before replacing any electrical components.
Roadside Emergencies COLOR Fuse rating Mini fuses Standard fuses Maxi fuses 60A 70A 80A — — — — — — Blue Tan Natural Cartridge Fuse link maxi cartridge fuses Yellow Yellow — Brown Black Black Passenger compartment fuse panel The fuse panel is located behind a trim panel on the left side of the driver’s footwell near the parking brake. To remove the trim panel, slide the release lever to the right then pull the trim panel out.
Roadside Emergencies 1 2 3 4 5 6 7 19 30 20 31 21 32 48 8 9 40 49 10 22 33 41 23 34 42 24 35 43 25 36 44 26 37 45 11 12 13 14 15 16 27 17 28 38 46 18 29 39 47 The fuses are coded as follows. Fuse/Relay Location 1 2 3 4 5 6 7 Fuse Amp Rating 30A 15A 30A 10A 20A 5A 7.
Roadside Emergencies Fuse/Relay Location 12 Fuse Amp Rating 15A 13 14 15 15A 15A 15A 16 17 18 10A 10A 10A 19 20 20A 20A 21 22 23 10A 20A 15A 24 15A 25 26 27 28 15A 5A 20A 15A 29 20A 30 31 15A 5A Protected Circuits Interior lighting, Puddle lamps, Backlighting Right turn/stop lamps and turn signals Left turn/stop lamps and turn signals Reverse lamps, Stop lamps (high-mounted) Low beam headlamps (right) Low beam headlamps (left) Keypad illumination, Brake shift interlock (BSI), Passenger com
Roadside Emergencies Fuse/Relay Location 32 Fuse Amp Rating 15A 33 34 10A 10A 35 36 37 38 39 40 41 5A 10A 10A 10A 15A 10A 7.
Roadside Emergencies WARNING: To reduce risk of electrical shock, always replace the cover to the power distribution box before reconnecting the battery or refilling fluid reservoirs. If the battery has been disconnected and reconnected, refer to the Battery section of the Maintenance and Specifications chapter.
Roadside Emergencies Fuse/Relay Location 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 Fuse Amp Rating — — — — — — 40A** 30A** 20A** 20A** — 30A** — — 40A** 20A** 30A** — 30A** — — — — — — — 38 39 — 40A** 60A** 40A** 40 262 2011 MKX (mkx) Owners Guide, 1st Printing USA (fus) Power Distribution Box Description Not used Starter relay Not used Fuel pump relay Not used Not used Blower motor Starter motor Power point #1 (console bin) Cargo area power point Not used Driver se
Roadside Emergencies Fuse/Relay Location 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 Fuse Amp Rating — 30A** 30A** — 5A* — — — — 15A* — — — — — — 20A* 58 59 60 61 62 63 64 65 66 67 68 69 70 10A* 10A* — 10A* 10A* 15A* 20A* 15A* — 20A* 15A* 15A* 10A* Power Distribution Box Description Not used Passenger seat ABS valves Rear washer relay Rain sensor Not used Not used Not used Not used Heated mirror Not used Not used (spare) Left TT stop/turn lamps relay Not used Wiper relay Not used Left high-intens
Roadside Emergencies Fuse/Relay Location 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 Fuse Amp Rating — — — — — — — 20A* 5A* — — 15A* — 20A* — 7.
Roadside Emergencies CHANGING THE TIRES If you get a flat tire while driving, do not apply the brake heavily. Instead, gradually decrease your speed. Hold the steering wheel firmly and slowly move to a safe place on the side of the road. Note: The tire pressure monitoring system (TPMS) indicator light will illuminate when the spare tire is in use. To restore the full functionality of the monitoring system, all road wheels equipped with tire pressure monitoring sensors must be mounted on the vehicle.
Roadside Emergencies A dissimilar spare tire/wheel is defined as a spare tire and/or wheel that is different in brand, size or appearance from the road tires and wheels and can be one of three types: 1. T-type mini-spare: This spare tire begins with the letter “T” for tire size and may have “Temporary Use Only” molded in the sidewall 2.
Roadside Emergencies The usage of a full-size dissimilar spare tire/wheel can lead to impairment of the following: • Handling, stability and braking performance • Comfort and noise • Ground clearance and parking at curbs • Winter weather driving capability • Wet weather driving capability • All-wheel driving capability (if applicable) • Load leveling adjustment (if applicable) When driving with the full-size dissimilar spare tire/wheel additional caution should be given to: • Towing a trailer • Driving vehi
Roadside Emergencies Removing the spare tire and jack 1. Lift the carpeted load floor panel located in the rear of the vehicle. 2. Remove the spare tire cover (if equipped). 3. Remove the wing nut securing the spare tire by turning it counterclockwise. 4. Remove the washer. 5. Lift and remove the temporary spare tire from the cargo area. 6. Remove the jack assembly from the vehicle. Loosen the bag tabs and remove the jack and lug wrench from the bag. 7.
Roadside Emergencies WARNING: Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel. Note: Passengers should not remain in the vehicle when the vehicle is being jacked. 1. Block the diagonally opposite wheel. 2. Loosen each wheel lug nut one-half turn counterclockwise but do not remove them until the wheel is raised off the ground.
Roadside Emergencies 3. Align the slot on top of the jack with the sheet metal flange indicated by the jack locator triangle next to the tire you are changing. Turn the jack handle clockwise until the wheel is completely off the ground. 4. Remove the lug nuts with the lug wrench. 5. Replace the flat tire with the spare tire, making sure the valve stem is facing outward. Reinstall the lug nuts until the wheel is snug against the hub. Do not fully tighten the lug nuts until the wheel has been lowered. 6.
Roadside Emergencies If you are stowing a flat 22 inch tire and wheel assembly, temporarily remove the load floor, plastic stowage bins (if equipped), and the foam load floor supports to make space for the 22 inch tire and wheel assembly. Place the 22 inch tire & wheel assembly in the spare tire well with the valve stem facing down. Rotate the tire until the jack assembly is able to protrude through a wheel opening.
Roadside Emergencies Note: Inspect the wheel pilot hole prior to installation. If there is visible corrosion in wheel pilot hole, remove loose particles by wiping with clean rag and apply grease. Apply grease only to the wheel pilot hole surface by smearing a “dime” (1 square cm) sized glob of grease around the wheel pilot surface (1) with end of finger. DO NOT apply grease to lugnut/stud holes or wheel-to-brake surfaces.
Roadside Emergencies Preparing your vehicle When the battery is disconnected or a new battery is installed, the automatic transmission must relearn its shift strategy. As a result, the transmission may have firm and/or soft shifts. This operation is considered normal and will not affect function or durability of the transmission. Over time, the adaptive learning process will fully update transmission operation. 1. Use only a 12–volt supply to start your vehicle. 2.
Roadside Emergencies 4 + – + 1 – 1. Connect the positive (+) jumper cable to the positive (+) terminal of the discharged battery. 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery. 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery. 4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’s engine, away from the battery and the carburetor/fuel injection system.
Roadside Emergencies Removing the jumper cables Remove the jumper cables in the reverse order that they were connected. – – Note: In the illustration, the vehicle on the bottom is used to designate the assisting (boosting) battery. 1. Remove the jumper cable from the ground metal surface. 2. Remove the jumper cable on the 4 D 1 D A negative (-) terminal of the booster vehicle’s battery. + 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’s battery. 4.
Roadside Emergencies WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or, if you are a member of a roadside assistance program, your roadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift and dollies or flatbed equipment. Do not tow with a slingbelt. Ford Motor Company has not approved a slingbelt towing procedure.
Roadside Emergencies If the vehicle is towed by other means or incorrectly, vehicle damage may occur. Ford Motor Company produces a towing manual for all authorized tow truck operators. Have your tow truck operator refer to this manual for proper hook-up and towing procedures for your vehicle.
Customer Assistance GETTING THE SERVICES YOU NEED Warranty repairs to your vehicle must be performed by an authorized Ford, Lincoln, or Mercury dealer. While any authorized dealer handling your vehicle line will provide warranty service, we recommend you return to your selling authorized dealer who wants to ensure your continued satisfaction. Please note that certain warranty repairs require special training and/or equipment, so not all authorized dealers are authorized to perform all warranty repairs.
Customer Assistance In Canada: Mailing address (Ford vehicles) Customer Relationship Centre Ford Motor Company of Canada, Limited P.O. Box 2000 Oakville, Ontario L6J 5E4 Telephone 1-800-565-3673 (FORD) Online www.ford.ca Mailing address (Lincoln vehicles) Lincoln Centre Ford Motor Company of Canada, Limited P.O. Box 2000 Oakville, Ontario L6J 5E4 Telephone 1-800-387-9333 Online www.lincolncanada.
Customer Assistance In the United States, a warranty dispute must be submitted to the BBB AUTO LINE before taking action under the Magnuson-Moss Warranty Act, or to the extent allowed by state law, before pursuing replacement or repurchase remedies provided by certain state laws. This dispute handling procedure is not required prior to enforcing state created rights or other rights which are independent of the Magnuson-Moss Warranty Act or state replacement or repurchase laws. IN CALIFORNIA (U.S.
Customer Assistance LINE before exercising rights or seeking remedies created by the Federal Magnuson-Moss Warranty Act, 15 U.S.C. sec. 2301 et seq. If you choose to seek redress by pursuing rights and remedies not created by California Civil Code Section 1793.22(b) or the Magnuson-Moss Warranty Act, resort to BBB AUTO LINE is not required by those statutes. THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM (U.S. ONLY) Your satisfaction is important to Ford Motor Company and to your dealer.
Customer Assistance You can get more information by calling BBB AUTO LINE at 1-800-955-5100, or writing to: BBB AUTO LINE 4200 Wilson Boulevard, Suite 800 Arlington, Virginia 22203–1833 BBB AUTO LINE applications can also be requested by calling the Ford Motor Company Customer Relationship Center at 1-800-392-3673. Note: Ford Motor Company reserves the right to change eligibility limitations, modify procedures, or to discontinue this process at any time without notice and without obligation.
Customer Assistance The use of leaded fuel in your vehicle without proper conversion may damage the effectiveness of your emission control system and may cause engine knocking or serious engine damage. Ford Motor Company/Ford of Canada is not responsible for any damage caused by use of improper fuel. Using leaded fuel may also result in difficulty importing your vehicle back into the U.S. If your vehicle must be serviced while you are traveling or living in Asia-Pacific Region, Sub-Saharan Africa, U.S.
Customer Assistance If your vehicle must be serviced while you are traveling or living in the Middle East, contact the nearest authorized dealer. If the authorized dealer cannot help you, contact: Ford Middle East Customer Relationship Center P.O. Box 21470 Dubai, United Arab Emirates Telephone: +971 4 3326084 FAX: +971 4 3327299 Email: menacac@ford.com www.me.ford.
Customer Assistance REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
Cleaning WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutral pH shampoo, such as Motorcraft威 Detail Wash (ZC-3-A), which is available from your authorized dealer. • Never use strong household detergents or soap, such as dish washing or laundry liquid. These products can discolor and spot painted surfaces. • Never wash a vehicle that is “hot to the touch” or during exposure to strong, direct sunlight.
Cleaning • Do not allow paint sealant to come in contact with any non-body (low-gloss black) colored trim, such as grained door handles, roof racks, bumpers, side moldings, mirror housings or the windshield cowl area. The paint sealant will “gray” or stain the parts over time. PAINT CHIPS Your authorized dealer has touch-up paint to match your vehicle’s color. Take your color code (printed on a sticker in the driver’s door jamb) to your authorized dealer to ensure you get the correct color.
Cleaning • Spray Motorcraft Engine Shampoo and Degreaser (ZC-20) on all parts that require cleaning and pressure rinse clean. In Canada, use Motorcraft Engine Shampoo (CXC-66-A). • Cover the highlighted areas to prevent water damage when cleaning the engine. • Never wash or rinse the engine while it is hot or running; water in the running engine may cause internal damage. • Never wash or rinse any ignition coil, spark plug wire or spark plug well, or the area in and around these locations.
Cleaning may cause squeaking or chatter noise from the blades, and streaking and smearing of the windshield. To clean these items, follow these tips: • The windshield, rear windows and side windows may be cleaned with a non-abrasive cleaner such as Motorcraft威 Ultra-Clear Spray Glass Cleaner (ZC-23), available from your authorized dealer. • The wiper blades can be cleaned with isopropyl (rubbing) alcohol or Motorcraft威 Premium Windshield Washer Concentrate (ZC-32-A) in the U.S.
Cleaning • Be certain to wash or wipe your hands clean if you have been in contact with certain products such as insect repellent and suntan lotion in order to avoid possible damage to the interior painted surfaces. • Do not use household or glass cleaners as these may damage the finish of the instrument panel, interior trim and cluster lens. • Do not allow air fresheners and hand sanitizers to spill on interior surfaces. If a spill occurs, wipe off immediately. Damage may not be covered by your warranty.
Cleaning • Do not use household cleaning products or glass cleaners, which can stain and discolor the fabric and affect the flame retardant abilities of the seat materials. WARNING: Do not use cleaning solvents, bleach or dye on the vehicle’s seatbelts, as these actions may weaken the belt webbing. LEATHER SEATS (IF EQUIPPED, EXCEPT FOR THE KING RANCH姞 EDITION) For King Ranch威 leather seats, refer to a separate section in this chapter. • Clean spills and stains as quickly as possible.
Cleaning • Clean spills as quickly as possible. • Test any cleaner or stain remover on an inconspicuous part of the leather as cleaners may darken the leather. • Do not spill coffee, ketchup, mustard, orange juice or oil-based products on the leather as they may permanently stain the leather. • Do not use household cleaning products, alcohol solutions, solvents or cleaners intended for rubber, vinyl or plastics.
Cleaning FORD AND LINCOLN MERCURY CAR CARE PRODUCTS Your Ford or Lincoln Mercury authorized dealer has many quality products available to clean your vehicle and protect its finishes. These quality products have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and appearance of your vehicle. Each product is made from high quality materials that meet or exceed rigid specifications.
Maintenance and Specifications SERVICE RECOMMENDATIONS To help you service your vehicle, we provide scheduled maintenance information which makes tracking routine service easy. If your vehicle requires professional service, your authorized dealer can provide the necessary parts and service. Check your Warranty Guide to find out which parts and services are covered. Use only recommended fuels, lubricants, fluids and service parts conforming to specifications.
Maintenance and Specifications OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the bottom of the instrument panel near the steering column. 2. Go to the front of the vehicle and release the secondary hood latch that is located under the front center of the hood. 3. Lift the hood and support it with the prop rod.
Maintenance and Specifications IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 3 2 1 10 9 8 1. Engine coolant reservoir 2. Power steering fluid reservoir 3. Brake fluid reservoir 4. Battery 5. Power distribution box 6. Air filter assembly 7. Transmission fluid dipstick 8. Engine oil dipstick 9. Engine oil filler cap 10.
Maintenance and Specifications WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if the level is low. In very cold weather, do not fill the reservoir completely. Only use a washer fluid that meets Ford specifications. Do not use any special washer fluid such as windshield water repellent type fluid or bug wash. They may cause squeaking, chatter noise, streaking and smearing. Refer to Maintenance product specifications and capacities in this chapter.
Maintenance and Specifications To prolong the life of the wiper blades, it is highly recommended to scrape off the ice on the windshield before turning on the wipers. The layer of ice has many sharp edges and can damage the micro edge of the wiper rubber element. Changing rear window wiper blade The rear wiper arm is designed without a service position. This reduces the risk of damage to the blade in an automatic car wash. To replace the wiper blade: 1.
Maintenance and Specifications 4. Open the hood. Protect yourself from engine heat. 5. Locate and carefully remove the engine oil level dipstick. 6. Wipe the dipstick clean. Insert the dipstick fully, then remove it again. • If the oil level is within this range, the oil level is acceptable. DO NOT ADD OIL. • If the oil level is below this mark, engine oil must be added to raise the level within the normal operating range.
Maintenance and Specifications • If required, add engine oil to the engine. Refer to Adding engine oil in this chapter. • Do not overfill the engine with oil. Oil levels above this mark may cause engine damage. If the engine is overfilled, some oil must be removed from the engine by an authorized dealer. 7. Put the dipstick back in and ensure it is fully seated. Adding engine oil 1. Check the engine oil. For instructions, refer to Checking the engine oil in this chapter. 2.
Maintenance and Specifications Use SAE 5W-20 engine oil Only use oils certified for gasoline engines by the American Petroleum Institute (API). An oil with this trademark symbol conforms to the current engine and emission system protection standards and fuel economy requirements of the International Lubricant Standardization and Approval Committee (ILSAC), comprised of U.S. and Japanese automobile manufacturers.
Maintenance and Specifications If your battery has a cover/shield, make sure it is reinstalled after the battery has been cleaned or replaced. For longer, trouble-free operation, keep the top of the battery clean and dry. Also, make certain the battery cables are always tightly fastened to the battery terminals. If you see any corrosion on the battery or terminals, remove the cables from the terminals and clean with a wire brush. You can neutralize the acid with a solution of baking soda and water.
Maintenance and Specifications RN TU LE AD RE Because your vehicle’s engine is electronically controlled by a computer, some control conditions are maintained by power from the battery. When the battery is disconnected or a new battery is installed, the engine must relearn its idle and fuel trim strategy for optimum driveability and performance. To begin this process: 1. With the vehicle at a complete stop, set the parking brake. 2.
Maintenance and Specifications ENGINE COOLANT Checking engine coolant The concentration and level of engine coolant should be checked at the intervals listed in scheduled maintenance information. The coolant concentration should be maintained at 50/50 coolant and distilled water, which equates to a freeze point of -34°F (-36°C). Coolant concentration testing is possible with a hydrometer or antifreeze tester.
Maintenance and Specifications Adding engine coolant When adding coolant, make sure it is a 50/50 mixture of engine coolant and distilled water. Add the mixture to the coolant reservoir, when the engine is cool, until the appropriate fill level is obtained. If coolant is filled to the COLD FILL RANGE or FULL COLD level when the engine is not cool, the system will remain underfilled. WARNING: Do not add engine coolant when the engine is hot.
Maintenance and Specifications a coolant degas system with a pressurized cap, or if it is necessary to remove the coolant pressure relief cap on the radiator of a vehicle with an overflow system, follow these steps to add engine coolant. WARNING: To reduce the risk of personal injury, make sure the engine is cool before unscrewing the coolant pressure relief cap. The cooling system is under pressure; steam and hot liquid can come out forcefully when the cap is loosened slightly.
Maintenance and Specifications Recycled engine coolant Ford Motor Company does NOT recommend the use of recycled engine coolant since a Ford-approved recycling process is not yet available. Used engine coolant should be disposed of in an appropriate manner. Follow your community’s regulations and standards for recycling and disposing of automotive fluids.
Maintenance and Specifications Vehicles driven year-round in non-extreme climates should use a 50/50 mixture of engine coolant and distilled water for optimum cooling system and engine protection. What you should know about fail-safe cooling If the engine coolant supply is depleted, this feature allows the vehicle to be driven temporarily before incremental component damage is incurred. The “fail-safe” distance depends on ambient temperatures, vehicle load and terrain.
Maintenance and Specifications 4. Check the coolant level and replenish if low. WARNING: Fail-safe mode is for use during emergencies only. Operate the vehicle in fail-safe mode only as long as necessary to bring the vehicle to rest in a safe location and seek immediate repairs.
Maintenance and Specifications WARNING: Gasoline may contain benzene, which is a cancer-causing agent. Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materials and any open flames before refueling your vehicle. • Always turn off the vehicle before refueling. • Automotive fuels can be harmful or fatal if swallowed. Fuel such as gasoline is highly toxic and if swallowed can cause death or permanent injury.
Maintenance and Specifications WARNING: The flow of fuel through a fuel pump nozzle can produce static electricity, which can cause a fire if fuel is pumped into an ungrounded fuel container. Refueling • • • • • • • WARNING: Fuel vapor burns violently and a fuel fire can cause severe injuries.
Maintenance and Specifications 2. Open the fuel filler door. 3. Slowly insert the fuel filler nozzle fully into the fuel system and leave the nozzle fully inserted until you are done pumping. Pump fuel as normal. 4. After you are done pumping fuel, wait about five seconds before slowly removing the fuel filler nozzle. This allows residual fuel to drain back into the fuel tank and not spill onto the vehicle. Note: A fuel spillage concern may occur if overfilling the fuel tank.
Maintenance and Specifications Note: Use of any fuel other than those recommended may cause powertrain damage, a loss of vehicle performance, and repairs may not be covered under warranty. Octane recommendations Your vehicle is designed to use “Regular” unleaded gasoline with a pump (R+M)/2 octane rating of 87. Some stations offer fuels posted as (R+M)/2 METHOD “Regular” with an octane rating below 87, particularly in high altitude areas. Fuels with octane levels below 87 are not recommended.
Maintenance and Specifications Running out of fuel Avoid running out of fuel because this situation may have an adverse effect on powertrain components. If you have run out of fuel: • You may need to cycle the ignition from off to on several times after refueling to allow the fuel system to pump the fuel from the tank to the engine. On restarting, cranking time will take a few seconds longer than normal. With keyless ignition, just start the engine. Crank time will be longer than usual.
Maintenance and Specifications 1. After lifting the trunk cargo cover, locate the white plastic funnel. It is attached to the rear, lower edge of the spare tire compartment. 2. Slowly insert the funnel into the Easy Fuel™ system. 3. Fill the vehicle with fuel from the portable fuel container. 4. When done, clean the funnel or properly dispose of it. Extra funnels can be purchased from your authorized dealer if you choose to dispose of the funnel.
Maintenance and Specifications Filling the tank The advertised fuel capacity of the fuel tank on your vehicle is equal to the rated refill capacity of the fuel tank as listed in the Maintenance product specifications and capacities section of this chapter. The advertised capacity is the amount of the indicated capacity and the empty reserve combined. Indicated capacity is the difference in the amount of fuel in a full tank and a tank when the fuel gauge indicates empty.
Maintenance and Specifications Calculation 2: Multiply liters used by 100, then divide by total kilometers traveled. Keep a record for at least one month and record the type of driving (city or highway). This will provide an accurate estimate of the vehicle’s fuel economy under current driving conditions. Additionally, keeping records during summer and winter will show how temperature impacts fuel economy. In general, lower temperatures give lower fuel economy.
Maintenance and Specifications • Use recommended engine oil. Refer to Maintenance product specifications and capacities in this chapter. • Perform all regularly scheduled maintenance items. Follow the recommended maintenance schedule and owner maintenance checks found in scheduled maintenance information. Conditions • Heavily loading a vehicle may reduce fuel economy at any speed. • Carrying unnecessary weight may reduce fuel economy (approximately 1 mpg [0.
Maintenance and Specifications If other than Ford, Motorcraft威 or Ford-authorized parts are used for maintenance replacements or for service of components affecting emission control, such non-Ford parts should be equivalent to genuine Ford Motor Company parts in performance and durability. WARNING: Do not park, idle, or drive your vehicle in dry grass or other dry ground cover. The emission system heats up the engine compartment and exhaust system, which can start a fire.
Maintenance and Specifications 2. Poor fuel quality or water in the fuel—the engine may misfire or run poorly. 3. The fuel fill inlet may not have been properly closed. See Easy Fuel™ “no cap” fuel system in this chapter. 4. Driving through deep water—the electrical system may be wet. These temporary malfunctions can be corrected by filling the fuel tank with good quality fuel, properly closing the fuel fill inlet or letting the electrical system dry out.
Maintenance and Specifications The OBD-II system is designed to check the emission control system during normal driving. A complete check may take several days. If the vehicle is not ready for I/M testing, the following driving cycle consisting of mixed city and highway driving may be performed: 15 minutes of steady driving on an expressway/highway followed by 20 minutes of stop-and-go driving with at least four 30-second idle periods.
Maintenance and Specifications BRAKE FLUID The fluid level will drop slowly as the brakes wear, and will rise when the brake components are replaced. Fluid levels between the MIN and MAX lines are within the normal operating range; there is no need to add fluid. If the fluid levels are outside of the normal operating range, the performance of the system could be compromised; seek service from your authorized dealer immediately.
Maintenance and Specifications 5. Remove the dipstick, wiping it clean with a clean, dry lint free rag. If necessary, refer to Identifying components in the engine compartment in this chapter for the location of the dipstick. 6. Install the dipstick making sure it is fully seated in the filler tube by turning it to the locked position. 7. Remove the dipstick and inspect the fluid level. The fluid should be in the designated areas for normal operating temperature.
Maintenance and Specifications Use of a non-approved automatic transmission fluid may cause internal transmission component damage. If necessary, add fluid in 1/2 pint (250 ml) increments through the filler tube until the level is correct. If an overfill occurs, excess fluid MIN MAX should be removed by an authorized dealer. An overfill condition of transmission fluid may cause shift and/or engagement concerns and/or possible damage.
Maintenance and Specifications housing and cover. This could cause filter damage and allow unfiltered air to enter the engine if not properly seated. 6. Replace the air filter housing cover and secure the clamps. Be sure that the air cleaner cover tabs are engaged into the slots of the air cleaner housing. Note: Failure to use the correct air filter element may result in severe engine damage. The customer warranty may be void for any damage to the engine if the correct air filter element is not used.
Maintenance and Specifications • Lubricate all hood, door and trunk lid hinges, and latches with a light grade oil. See the Cleaning chapter for more information. • Cover interior trim to prevent fading. • Keep all rubber parts free from oil and solvents. Engine • The engine oil and filter should be changed prior to storage, as used engine oil contain contaminates that may cause engine damage. • Start the engine every 15 days. Run at fast idle until it reaches normal operating temperature.
Maintenance and Specifications Tires • Maintain recommended air pressure. Miscellaneous • Make sure all linkages, cables, levers and pins under vehicle are covered with grease to prevent rust. • Move vehicles at least 25 feet (8 m) every 15 days to lubricate working parts and prevent corrosion. Removing vehicle from storage When your vehicle is ready to come out of storage, do the following: • Wash your vehicle to remove any dirt or grease film build-up on window surfaces.
Maintenance and Specifications MOTORCRAFT PART NUMBERS Component Engine air filter element Battery Oil filter Spark plugs 1 3.7L V6 engine FA-1884 BXT-65 FL-500-S SP-5201 Refer to scheduled maintenance information for the appropriate intervals for changing the spark plugs. Replace the spark plugs with ones that meet Ford material and design specifications for your vehicle, such as Motorcraft威 or equivalent replacement parts.
— — — Brake fluid Door weatherstrips Door latch, hood latch, auxiliary hood latch, door hinges, striker plates, seat tracks and fuel filler door hinge Lock cylinders XG-4 or XL-5 or equivalent / ESB-M1C93-B XL-1 / None Multi-Purpose Grease (Lithium grease) Motorcraft威 Penetrating and Lock Lubricant XL-6 / ESR-M13P4-A PM-1-C / WSS-M6C62-A or WSS-M6C65-A1 Motorcraft威 High Performance DOT 3 Motor Vehicle Brake Fluid Between MIN and MAX on reservoir Silicone Spray Lubricant Ford Part Number / Ford S
2011 MKX (mkx) Owners Guide, 1st Printing USA (fus) Rear differential (AWD) fluid Automatic transmission fluid Power steering fluid Engine coolant Engine oil1 Item Ford Part Name •Motorcraft威 SAE 5W-20 Premium Synthetic Blend Motor Oil (US) •Motorcraft威 SAE 5W-20 Full Synthetic Motor Oil (US) 5.5 quarts (5.2L) •Motorcraft威 SAE 5W-20 Super Premium Motor Oil (Canada) •Motorcraft威 SAE 5W-20 Synthetic Motor Oil (Canada) Motorcraft威 Specialty 11.7 quarts Green Engine Coolant (11.
12 ounces (0.35L) Fill as required Power Transfer Unit (PTU) fluid (AWD)5 Windshield washer fluid Ford Part Number / Ford Specification Motorcraft威 SAE 75W-140 XY-75W140-QL / Synthetic Rear Axle WSL-M2C192-A Lubricant Motorcraft威 Premium Windshield Washer ZC-32-A (US) Concentrate (US) CXC-37-(A, B, D, and F) Premium Quality (Canada)/ Windshield Washer Fluid WSB-M8B16-A2/- (Canada) Ford Part Name Fuel tank 19.2 gallons — — (front-wheel drive) (72.7L) Fuel tank (all-wheel 20.8 gallons — — drive) (78.
Maintenance and Specifications ENGINE DATA Engine Cubic inches Required fuel Firing order Ignition system Compression ratio Spark plug gap 3.7L V6 engine 226 87 octane 1–4–2–5–3–6 Coil on plug 10.3:1 0.049–0.053 inch (1.25–1.35 mm) Engine drivebelt routing 1. Short drivebelt is on first pulley groove closest to engine. 2. Long drivebelt is on second pulley groove farthest from engine.
Maintenance and Specifications IDENTIFYING YOUR VEHICLE Safety Compliance Certification Label The National Highway Traffic Safety Administration Regulations require that a Safety Compliance Certification Label be affixed to a vehicle and prescribe where the Safety Compliance Certification Label may be located. The Safety Compliance Certification Label is located on the structure (B-Pillar) by the trailing edge of the driver’s door or the edge of the driver’s door.
Maintenance and Specifications The Vehicle Identification Number (VIN) contains the following information: 1. World manufacturer identifier 2. Brake system / Gross Vehicle Weight Rating (GVWR) / Restraint Devices and their location 3. Make, vehicle line, series, body type 4. Engine type 5. Check digit 6. Model year 7. Assembly plant 8. Production sequence number TRANSMISSION CODE DESIGNATIONS You can find a transmission code on the Safety Compliance Certification Label.
Accessories LINCOLN CUSTOM ACCESSORIES FOR YOUR VEHICLE A wide selection of Lincoln Custom Accessories are available for your vehicle through your local Lincoln or Ford of Canada dealer. These quality accessories have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and aerodynamic appearance of your vehicle.
Accessories Peace of mind •Remote start •Keyless entry keypad •Cargo security shade •Wheel locks •Vehicle tracking and recovery* •Protective seat covers* •Windshield wiper shaker* •Bumper and hitch mounted parking sensors* *Ford Licensed Accessories (FLA) are warranted by the accessory manufacturer’s warranty. Ford Licensed Accessories are fully designed and developed by the accessory manufacturer and have not been designed or tested to Ford Motor Company engineering requirements.
Ford Extended Service Plan FORD ESP EXTENDED SERVICE PLANS (U.S. ONLY) More than 30 million Ford, Lincoln, and Mercury owners have discovered the powerful protection of Ford ESP. It is the only extended service plan backed by Ford Motor Company, and provides “peace of mind” protection beyond the New Vehicle Limited Warranty coverage. Up to 500+ Covered Vehicle Components There are four, new-vehicle Extended Service Plans with different levels of coverage. Ask your dealer for details.
Ford Extended Service Plan Ford ESP Can Quickly Pay for Itself One service bill – the cost of parts and labor – can easily exceed the price of your Ford ESP Service Contract. With Ford ESP, you minimize your risk for unexpected repair bills and rising repair costs. Avoid the rising cost of properly maintaining your vehicle! Ford ESP also offers a Premium Maintenance Plan that covers items that routinely wear out. The coverage is prepaid, so you never have to worry about affording your vehicle maintenance.
Ford Extended Service Plan 339 2011 MKX (mkx) Owners Guide, 1st Printing USA (fus)
Ford Extended Service Plan FORD ESP EXTENDED SERVICE PLANS (CANADA ONLY) You can get more protection for your vehicle by purchasing a Ford Extended Service Plan (ESP). Ford ESP is the only service contract backed by Ford Motor Company.
Scheduled Maintenance Guide GENERAL MAINTENANCE INFORMATION Why maintain your vehicle? This guide describes the scheduled maintenance required for your vehicle. Carefully following this schedule helps protect against major repair expenses resulting from neglect or inadequate maintenance and may also help to increase the value of your vehicle when you sell or trade it.
Scheduled Maintenance Guide If your message center is prematurely reset or becomes inoperative, you should perform the oil change interval at six months or 5,000 miles (8,000 km) from your last oil change. Your vehicle is very sophisticated and built with multiple complex performance systems. Every manufacturer develops these systems using different specifications and performance features.
Scheduled Maintenance Guide Genuine Ford parts and service When planning your maintenance services, consider your Ford and Lincoln Mercury dealership for all your vehicle’s needs. Get the most from your service and maintenance visits There are a lot of reasons why visiting your Ford or Lincoln Mercury dealership for all your service needs is a great way to help keep your vehicle running great. Convenience Many dealerships have extended evening and Saturday hours to make your service visit more convenient.
Scheduled Maintenance Guide WHICH MAINTENANCE SCHEDULE SHOULD YOU FOLLOW? Owner checks and services Certain basic maintenance checks and inspections should be performed by the owner or a service technician at the intervals indicated. Service information and supporting specifications are provided in this Owner’s Guide. Any adverse condition should be brought to the attention of your dealer or qualified service technician as soon as possible for the proper service advice.
Scheduled Maintenance Guide Multi-point inspection In order to keep your vehicle running right, it is important to have the systems on your vehicle checked regularly. This can help identify potential issues and prevent major problems. Ford Motor Company recommends the following multi-point inspection be performed at every scheduled maintenance interval to help ensure your vehicle keeps running great.
Scheduled Maintenance Guide 346 2011 MKX (mkx) Owners Guide, 1st Printing USA (fus)
Scheduled Maintenance Guide NORMAL SCHEDULED MAINTENANCE AND LOG For your convenience, your vehicle is equipped with a message center which determines the proper oil change service interval. You should perform the engine oil change as indicated by the instrument cluster message center. The message center will display ENGINE OIL CHANGE SOON or OIL CHANGE REQUIRED to indicate when an oil change is needed.
Oil Change Service Interval* 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Change engine oil and filter • • • • • • • • • • • • • • • Rotate tires, inspect tire wear and measure • • • • • • • • • • • • • • • tread depth Inspect wheels and related components for • • • • • • • • • • • • • • • abnormal noise, wear, looseness or drag Perform multi-point inspection (recommended) • • • • • • • • • • • • • • • Inspect automatic transmission fluid level (if • • • • • • • • • • • • • • • equipped with dipstick); consult deale
Scheduled Maintenance Guide Perform the services noted in the following table at the specified time/mileage (km) period either within 3,000 miles (5,000 km) of the OIL CHANGE REQUIRED message appearing in the message center or when the time/mileage (km) reading indicates service is due. Example #1: The OIL CHANGE REQUIRED message comes on at 28,751 miles (46,270 km); perform the 30,000 mile (48,000 km) automatic transmission fluid replacement.
Scheduled Maintenance Guide Maintenance schedule log DEALER VALIDATION: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P
Scheduled Maintenance Guide DEALER VALIDATION: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE:
Scheduled Maintenance Guide DEALER VALIDATION: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE:
Scheduled Maintenance Guide SPECIAL OPERATING CONDITIONS If you operate your Ford/Lincoln/Mercury vehicle primarily in one of the more demanding Special Operating Conditions listed below, you will need to have some items maintained more frequently. If you only occasionally operate your vehicle under these conditions, it is not necessary to perform the additional maintenance. For specific recommendations, see your Ford or Lincoln Mercury dealership service advisor or technician.
Scheduled Maintenance Guide Extensive idling and/or low-speed driving for long distances as in heavy commercial use such as delivery, taxi, patrol car or livery As required – Change engine oil and replace oil filter as indicated by message center and perform services as listed in the Normal Scheduled Maintenance chart (except Fiesta). Inspect frequently, service as – Replace cabin air filter (if equipped). required – Replace engine air filter.
Scheduled Maintenance Guide Operating in dusty conditions such as unpaved or dusty roads Inspect frequently, service as – Replace cabin air filter (if equipped). required – Replace engine air filter. Every 5,000 miles (8,000 km) – Inspect the wheels and related components for abnormal noise, wear, looseness or drag. – Rotate tires, inspect tires for wear and measure tread depth. Every 5,000 miles (8,000 km) or – Change engine oil and replace oil filter.
Scheduled Maintenance Guide Special operating condition log DEALER VALIDATION: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: D
Scheduled Maintenance Guide DEALER VALIDATION: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE:
Scheduled Maintenance Guide EXCEPTIONS In addition, there are several exceptions to the Normal Schedule. They are listed below: Normal vehicle axle maintenance ❑ Rear axles and power take-off (PTO) units containing synthetic lubricant and light duty trucks equipped with Ford-design axles are lubricated for life. These lubricants are not to be checked or changed unless a leak is suspected, service is required or the axle assembly has been submerged in water.
Scheduled Maintenance Guide COOLANT CHANGE RECORD Engine coolant ❑ ❑ 6 years or 100,000 miles (160,000 km) - change coolant (whichever comes first). After initial change - change coolant every 3 years or 50,000 miles (80,000 km).
Scheduled Maintenance Guide Engine coolant change log DEALER VALIDATION: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE:
Index A B Accessory delay ..........................65 Adaptive Cruise Control .............69 AdvanceTrac ..............................218 Air cleaner filter ...............324, 328 Air conditioning ..........................36 Airbag supplemental restraint system ................143–144, 152, 155 and child safety seats ............145 description ..............144, 152, 155 disposal ....................................158 driver airbag ............146, 152, 156 indicator light .........
Index recommendations ...................161 Child safety seats - booster seats ...........................................172 Cleaning your vehicle engine compartment ..............287 instrument panel ....................289 interior .....................................290 plastic parts ............................288 safety belts ..............................290 washing ....................................286 waxing .....................................286 wheels ......................................
Index dipstick ....................................298 filter, specifications ........300, 328 recommendations ...................300 refill capacities ........................329 specifications ..........................329 Event data recording ....................7 Exhaust fumes ..........................214 G F H Fail safe cooling ........................308 Fleet MyKey programming ........91 Floor mats .............................83–84 Fluid capacities .........................329 Fog lamps .......
Index Instrument panel cleaning ...................................289 cluster ........................................12 lighting up panel and interior .......................................47 Intelligent Access Key ................91 Intelligent Access with push button start ...............................102 J Jack ............................................265 positioning ...............................265 storage .....................................265 Jump-starting your vehicle ......
Index Parts (see Motorcraft威 parts) ...........328 Passenger Occupant Classification Sensor .................130 Power distribution box (see Fuses) ...............................260 Power door locks ........................97 Power liftgate ..............................84 Power mirrors .............................66 Power point .................................62 Power steering ..........................224 fluid, checking and adding ....321 fluid, refill capacity ................
Index SecuriCode keyless entry system ........................................110 SecuriLock passive anti-theft system ........................................112 Servicing your vehicle ..............294 SOS Post Crash Alert ...............158 Spare tire (see Changing the Tire) ...........268 Spark plugs, specifications .....................328, 332 Specification chart, lubricants ...................................329 Speed control ..............................67 Starting your vehicle ........
Index W Warning lights (see Lights) .......12 Washer fluid ..............................297 Water, Driving through .............253 Windows power .........................................63 rear wiper/washer .....................59 Windshield washer fluid and wipers ..........................................57 checking and adding fluid .....297 replacing wiper blades ...297–298 Wrecker towing .........................
