CERAMIC HOB NICE LS60C3Z www.linarie.com.
Adherence to the directions for use in this manual is extremely important for health and safety. Failure to strictly adhere to the requirements in this manual may result in personal injury, property damage and affect your ability to make a claim under Linärie’s manufacturer’s warranty provided with your product. Products must be used, installed and operated in accordance with this manual.
1. GENERAL INFORMATION 1.1 Appliance Information A damaged appliance can be dangerous. If you find the appliance is damaged or marked, you must report it within 7 days if you wish to claim for damage/marks under the manufacturer’s warranty. This does not affect your statutory rights. Do not use a damaged appliance. Faulty components must only be replaced by genuine Linärie spare parts. The manufacturer can only guarantee the safety of the appliance when Linärie replacement parts are used.
2.3 Correct Use & Operation After use, always turn off the cooking zones and the cooktop as described in this manual. Do not rely on the pan detection feature to turn off the cooking zones when you remove the pans. Only use the appliance on a dry, stable, level and horizontal surface and distance 10 cm back-round surrounding. When cooking, pay attention to the heat-up speed of the cooking zones.
cont. product introduction 3.3 Touch control panel LS60C3Z LS30C2Z 4. INSTALLATION 4.1 Selection of installation equipment Cut out the work surface according to the sizes shown in the drawing. For the purpose of installation and use, a minimum of 5 cm space shall be preserved around the hole. Be sure the thickness of the work surface is at least 30mm.
cont. installation The adhesive that join the plastic or wooden material of the furniture, MUST be heat resistant of not below 150ºC. The rear wall, adjacent and surrounding surfaces must be able to withstand a temperature of 90°C. 4.2 Before Installation Be sure the work surface is square and level, and no obstruction with space requirements. The work surface is made of heat – resistant and insulated material. If the hob is installed above an oven, the oven must have a cooling fan.
cont. installation 4.7 Connecting the ceramic hob to the mains power supply > Suitable Only (for the model without plug). The appliance must be connected to the mains by a qualified professional, who is familiar with and adheres to the local requirements and supplementary regulations of your electricity supplier. 1. Your household power supply must meet the power consumption of the appliance. 2. The voltage and power cord must meet the values on the technical data sheet. 3.
cont. operation 5.3 Using your ceramic hob 5.3.1 Start cooking 5.3.2 Finish cooking 1. Touch the heating zone selection control or that you want to switch off. 1. Touch the ON/OFF key, the cooktop display lits up. (display will disappear if no other key is touched within the next 30 seconds). 2. Turn the cooking zone off by touching “ ” key. 2. Place a suitable pan on the cooking zone that you wish to use. Make sure the bottom of the pan and the surface of the cooking zone are clean and dry. 3.
cont. operation 5.5 Over temperature protection 5.6 Heat residual warning An equipped temperature sensor can monitor the temperature inside the Ceramic hobs. When an excessive temperature is noticed, the ceramic hobs will stop the operation automatically. When the cooker has been working for sometime, there will be residual heat. The letter “H” will appear to keep you away from it. 5.7 Using the timer You can set it to turn one cooking zone off after setting up a time.
7. HEAT SETTINGS The settings below are guidelines only. The exact setting will depend on several factor, including your cookware and the amount you are cooking. Experiment with the induction hob to find the settings that best suit you. Suitability Heat setting 1-2 Delicate warming for small amount of food Melting chocolate, butter and foods that burn quickly.
10. FAILURE DISPLAY AND INSPECTION If abnormality occurs, the ceramic hob will enter to protective state automatically and displaya corresponding display codes. ERROR *E1 *E2 *E3 *E5 CAUSE - Check for low voltage. - Check for high voltage. - Thermal sensor stoppage - The plate temperature is high REMEDY - Check the voltage. - Check the voltage. - Replace the thermal sensor. - Reduce power or turn it off. 11.
LIKE TO KNOW MORE? For further information on all Linärie appliances, or to obtain detailed dimension and installation information, phone or email our Customer Care team or visit our website: Australia hello@linarie.com.au www.linarie.com.au Follow Us @Linarie.Appliances © Linärie www.linarie.com.
Operating and installation instructions: Original √ Translation Osass Australia Pty Ltd. ACN 005 635 398 ABN 96 005 635 398 Linärie Contact hello@linarie.com.au www.linarie.com.au The distribution and duplication of this document, as well as the use and disclosure of its contents are prohibited unless expressly authorised. These operating and installation instructions have been drawn up with the greatest of care.
