USER MANUAL LA35 ACTUATOR To learn more about LINAK, please visit: W W W. L I N A K .
Contents Preface ................................................................................................................................................................. 4 Safety instructions .............................................................................................................................................. 5 Important information .......................................................................................................................................
Preface We are delighted that you have chosen a product from LINAK. LINAK systems are high-tech products based on many years of experience in the manufacture and development of actuators, electronic control boxes, controls, and chargers. We are also constantly improving our products to meet customer requirements. This user manual will tell you how to install, use, and maintain your LINAK LA35 actuator. We are sure that the LA35 actuator will give you a problemfree operation.
Safety instructions Please read the following safety information carefully. Ensure that all staff who are to connect, mount, or use the actuator are in possession of the necessary information and that they have access to this user manual. Persons who do not have the necessary experience or knowledge of the product/ products must not use the product/products.
Important information Information about the actuators is described under the following two headings: Warning! Failing to follow these instructions can cause accidents resulting in serious personal injury. Failing to follow these instructions can result in the actuator suffering damage or being ruined.
DECLARATION OF CONFORMITY LINAK A/S Smedevænget 8 DK - 6430 Nordborg hereby declares that LINAK Actuator 35xxxxxxxxxxx2x complies with the EMC Directive: 2004/108/EC according to following harmonized standards: EN 61000-4-2:1995+A1+A2, EN 61000-4-3:2006, EN 61000-4-4:2004, EN 61000-4-5:1995+A1, EN 61000-4-6:1996+A1, EN 50121-3-2, EN 60204-31:1999 Additional information: The actuator does also comply with EMC parts of: The Machinery Directive 2006/42/EC The Recreational Craft Directive 94/25/EC The Vehicle
Misc. on the TECHLINETM actuator system Warranty There is a 12 months’ warranty on the TECHLINE products against manufacturing faults calculated from the production date of the individual products (see label). LINAK’s warranty is only valid in so far as the equipment has been used and maintained correctly and has not been tampered with. Furthermore, the actuator must not be exposed to violent treatment. In the event of this, the warranty will be ineffective/invalid.
Specifications Motor: Permanent magnet motor 12, or 24 * Cable: Motor: 2 x 14 AWG PVC cable Control: 6 x 20 AWG PVC cable ** Housing: The housing is made of casted aluminium, coated for outdoor out and in harsh conditions Spindle part: Outer tube: Powder coated steel Inner tube: Stainless steel AISi304/SS2333 Acme spindle: Trapezoidal spindle with high efficiency Temperature range: - 10o C to +50o C Full performance +5o C to +40o C End play: 2 mm maximum Weather protection: Rated IP66 for outdo
Mounting guidelines X LINAK® linear actuators are quickly and easily mounted by slipping pins through the holes on each end of the units and into brackets on the machine frame and the load. The mounting pins must be parallel to each other as shown in Figure 1. Pins, which are not parallel to each other, may cause the actuator to bend and be damaged. X Figure 1 The load should act along the stroke axis of the actuator since off centre loads may cause bending and lead to premature failure. See Figure 2.
Application hints The actuator is weatherproof for use in outdoor applications. The actuator can be washed down with a high pressure washer, but it should not be used under water. The duty cycle at max. load is 10% on time. This means if the actuator runs continuously for 2 minutes it must remain off for 18 minutes before operating again.
Electrical installation Be aware of BUS actuator - please see the installation guide. Motor connection Wiring: The actuator direction (forward, reverse) is controlled with a doublethrow switch with the centre postion “off”. + Motor Actuation To extend the actuator, connect brown to positive and blue to negative. To retract the actuator, connect blue to positive and brown to negative. Connection diagrams: Basic actuator Fig.
Actuator with potential free switches Fig.2 : 35xxxxx10xxxxx BROWN M BLUE RED YELLOW IN OUT GREEN Actuator with potential free switches and relative positioning Fig.3 : 35xxxxx0Hxxxxx & 35xxxxx1Hxxxxx M BROWN BLUE RED IN OUT YELLOW GREEN WHITE SIGNAL VIOLET BLACK Actuator with potential free switches and absolute positioning Fig.
Actuator with PLC-option Fig.
Connection of the LA35 with the CS16 MAX MIN P HB40 serie CS16-4-24 1 2 3 4 5 6 7 8 9 10 11 12 R GR O R = RED . O = ORANGE .
Mounting of cables • Unscrew the cover and remove the two blind plugs • Plug in the power cable and/or the signal cable • Slide the cover onto the actuator The torque of the cover screw is +/- 0.3 Nm Note: When changing the cables on a LINAK actuator, it is important that this is done carefully, in order to protect the plugs and pins. Please be sure that the plug is in the right location and fully pressed in before the cable lid is mounted. Accessories Cables: Power cables (Ordered separately) 1.
DRAWING APPENDIX TECHLINETM LA35: LA35 10.2 10.2 Installation dimension Installation dimension STROKE =<300 = 200 + STROKE STROKE >300 = 250 + STROKE Minimum Installation dimension = 300 mm 29 17 13 233 27 26 11 17 6.1 6.1 54 22 153 116 27 83.
Main groups of disposal Product Metal scrap Cable scrap Electronic scrap Plastic recycling or combustion X X X X LA35 LINAK’s products may be disposed of, possibly by dividing them into different waste groups for recycling or combustion. We recommend that our product is disassembled as much as possible at the disposal and that you try to recycle it.
LINAK APPLICATION POLICY The purpose of the application policy is to define areas of responsibilities in relation to applying a LINAK product defined as hardware, software, technical advice, etc. related to an existing or new customer application. LINAK products as defined above are applicable for a wide range of applications within the Medical, Furniture, Desk, and Industry areas.
FACTORIES CHINA LINAK (Shenzhen) Actuator Systems, Ltd. Phone: +86 755 8610 6656 . Fax: +86 755 8610 6990 E-mail: sales@linak.cn . www.linak.cn NETHERLANDS LINAK Actuator-Systems B.V. Phone: +31 76 5 42 44 40 . Fax: +31 76 5 42 61 10 E-mail: info@linak.nl . www.linak.nl IRAN Bod Inc. Phone: +98 2188998635 - 6 . Fax: +98 2188954481 E-mail: info@bod.ir . www.bod.ir DENMARK LINAK A/S . Group Headquarters Guderup Phone: +45 73 15 15 15 . Fax: +45 74 45 80 48 Fax (Sales): +45 73 15 16 13 E-mail: info@linak.
