User's Manual

21
1. Overview 2. Setup & Use
3. Optional
Accessories
4. Troubleshooting
5. Warranty, Safety
& Specifications
ALL PROBLEMS: Most Problems are
related to low battery power.
SOLUTION: Battery Check
UÊ wÀÊL>ÌÌiÀiÃÊ>ÀiÊV>À}i`Ê
each night. A blinking red LED on
the power button indicates a low
battery.
UÊ wÀÊ«À«iÀÊL>ÌÌiÀiÃÊ>ÀiÊ
used. The Flexmike requires the
Lightspeed NH2.4 rechargeable
sensing battery pack for proper
charging.
UÊÊÊ>iÊÃÕÀiÊÌiÊVÀ«iÃÊLÌ>Ê
a full charge. Full charge will last
up to eight hours.
UÊ 7iÊ«Õ}}}ÊÌiÊV>À}}ÊV>LiÊ
into the transmitter, ensure the red
charging LED turns on. The green
LED will turn on when a full charge
is reached.
PROBLEM: Flexmike does not
indicate a “Ready” signal (solid
blue or red LED)
SOLUTION: Follow these steps to
ensure the system is ready to use.
UÊ ÃÕÀiÊÌiÊ«ÜiÀÊÃÜÌVÊÊÌiÊ
Flexmike is turned on. Once
turned on, the blue LED should
begin blinking.
UÊ *ÜiÀÊÌiÊiÝiÊvv]ÊÌiÊÊ
again after a few seconds. Wait for
up to 30 seconds for the blue LED
to turn solid, indicating READY for
operation.
PROBLEM: Low Volume or Feedback
SOLUTION: Follow these steps to
eliminate low volume or feedback.
UÊ iVÊÛÕiÊiÛiÊÊÌiÊ
amplifier. If the volume is too
high, feedback will occur. Adjust
accordingly.
UÊ `ÕÃÌÊÌiÊÛÕiÊiÛiÊÊÌiÊ
Flexmike.
PROBLEM: No Sound From Amplifier
SOLUTION: Follow these steps to
produce sound from speakers.
UÊ wÀÊÌ>ÌÊÌiÊLÕiÊÊ*"7,Ê
light located on the front panel of
the Redcat Access is on.
UÊ wÀÊÌiÊiÝiÊÃÊi`Ê
to the Redcat Access. The mic 1
signal light will be green on the
Redcat Access indicating the
Flexmike is linked.
UÊÊ wÀÊÌ>ÌÊÌiÊiÝiÊ
is turned on. There will be a
solid blue LED on the top of
microphone to indicate it is
powered on and ready.
UÊÊ wÀÊÌ>ÌÊiÝiÊÃÊÌÊ
muted. A solid red LED on the top
of microphone will indicate it is
muted.
Note: Most problems are directly related to low battery power. Please run
through the “Battery Check” items first. For remaining troubleshooting, use
known good, fully-charged batteries.
If you review these instructions and still have questions, call Lightspeed
Technical Services at 800.732.8999, 5 a.m. – 5 p.m., PST.
Customers outside
the U.S. should contact their local reseller.
TROUBLESHOOTING
COMMON PROBLEMS AND SOLUTIONS