USER INSTRUCTIONS VENOM & GENESIS LIGHTFORCE.
VENOM LED & GENESIS LED INSTALLATION INSTRUCTIONS VENOM LED KIT CONTENTS • 1 x DL150 Venom LED light • 1 x Spot filter • 1 x Reversible mounting bracket (fitted loose to light) • 2 x M10 x 35mm stainless steel hex bolts with washers and nyloc nuts (side bolts fitted to light) • 1 x M10 x 35mm stainless steel hex bolt with washer and nyloc nut (fitted to bracket for mounting) • 1 x 4 pin waterproof harness adaptor • 1 x User instructions.
VENOM LED & GENESIS LED INSTALLATION INSTRUCTIONS TOOLS REQUIRED • 17mm socket on ratchet • 7/16” socket (optional for DL210 mounting) • Torque wrench. GENERAL C ARE AND SAFETY TIPS To wash your lights, use plenty of warm soapy water and a soft cloth only (this prevents surfaces from marking). Never use any solvent based cleaners or industrial detergents when cleaning these lights, as permanent damage may occur. PERSONAL SAFETY WARNING High intensity light source.
VENOM LED & GENESIS LED INSTALLATION INSTRUCTIONS IMPORTANT NOTES 1. Before fitting the stainless steel hardware, apply a small amount of anti-seize to the thread of the 35mm mounting bolts. 2. Mounting points vary in design and load capacity. Ensure the light is within manufacturers recommended weight specifications before fitment. 3. Failure to correctly mount light may cause damage to light and vehicle. MOUNTING BRACKET 4 1.
VENOM LED & GENESIS LED INSTALLATION INSTRUCTIONS OPTIONAL FOR GENESIS LED For high vibration environments we recommend fitting the supplied 1/4” x 1 1/4” long UNC stainless steel hex bolts with washers and nuts. Torqued to 8Nm. Side Bolt M10 x 35 Optional Mounting Bolt M10 x 35 Side Bolt M10 x 35 Fro nt F aci ng Optimum Mounting Bracket Position NOTE When lights are used in extreme environments always re-check torques. o The mounting bracket can be rotated 180 for an additional fitment option.
VENOM LED & GENESIS LED INSTALLATION INSTRUCTIONS ELECTRIC AL CONNECTIONS Venom LED and Genesis LED lights are fitted with a waterproof 4 pin electrical connector. Included in the kit is the mating connector fitted with short lengths of cable for integration with an appropriate wiring harness. i.e. Harness must be capable of 15A per light. If existing wiring harness is suitable, the included connector needs to be fitted directly to your existing driving light circuit.
VENOM LED & GENESIS LED INSTALLATION INSTRUCTIONS NOTE For maximum performance, three mode operation and safety, we recommend the use of optional wiring harness LFDLHTS – for fitment follow the installation instructions included with the harness. C AUTION Improper installation of the connector will affect the reliability and operation of your lights. Do not remove the waterproof connector from the driving light cable; this will lead to water ingress and void warranty.
VENOM LED & GENESIS LED INSTALLATION INSTRUCTIONS VENOM LED FILTER REMOVAL • Filter is held in place by 4 clips. • Lift tab at bottom of light and pull filter away from bezel releasing the clips. VENOM LED FILTER REFITTING • Insert the filter at the top position • Push filter onto bezel using filter tab until side clips are engaged • Ensure filter is correctly aligned within bezel.
VENOM LED & GENESIS LED INSTALLATION INSTRUCTIONS GENESIS LED FILTER REMOVAL • Unlock each filter tab from the light by lifting the rear of the tab away from the bezel • Swing the base of the filter away from the light • The filter will drop down and away from the light.
VENOM LED & GENESIS LED INSTALLATION INSTRUCTIONS VENOM LED TECHNIC AL SPECIFIC ATIONS • Power: 75 Watts • Colour temperature: 5000K • Raw lumens: 7850 • LED lifespan: up to 50,000 hours • Effective lumens: 6800 • Input cable length: 460mm (18.11”) • Input voltage range: 10 – 32V • Operating temperature: -40o to 63oC (-40o to 145oF) • Current draw: 5.7 Amps @13.2V • Weight including bracket: 1.2kg (2.
VENOM LED & GENESIS LED INSTALLATION INSTRUCTIONS GENESIS LED TECHNIC AL SPECIFIC ATIONS • Power: 140 Watts • Colour temperature: 5000K • Raw lumens: 13850 • LED lifespan: up to 50,000 hours • Effective lumens: 12000 • Input cable length: 460mm (18.11”) • Input voltage range: 10 – 32V • Operating temperature: -40o to 63oC (-40o to 145oF) • Current draw: 10.5 Amps @13.2V • Weight including bracket: 2.4kg (5.
VENOM LED & GENESIS LED INSTALLATION INSTRUCTIONS DRIVING LIGHT FILTERS Durable polycarbonate covers should remain fitted to driving lights at all times. They are capable of absorbing road grime and bombardment for many years. These replaceable covers should be renewed from time to time to protect your investment and maintain maximum beam output. Your Venom LED & Genesis LED lights come standard with spot filters. Clear combo filters are used to change the beam pattern.
VENOM LED & GENESIS LED INSTALLATION INSTRUCTIONS GENESIS LED TOP STAY BRACKET (Part No. DL210TSB) Your Genesis LED can be used with a top stay bracket for increased mounting rigidity.
VENOM LED & GENESIS LED INSTALLATION INSTRUCTIONS CROSS BOLT SECURITY FA STENER KIT The simple to install security bolts and nuts will help protect your investment. (Part No. ATNSG2) This kit contains 4 x M10 x 35mm anti-theft bolts plus 2 x M10 security nuts for the mounting bolts, both with corresponding coded keys requiring a 17mm, 11/16” spanner. For use with the Venom LED, Genesis LED and Striker LED Driving Lights.
VENOM LED & GENESIS LED INSTALLATION INSTRUCTIONS ORDER CODE DESCRIPTION ACCESSORIES LFDLHTS Driving light harness 12V 4 pin, 3 stage switch operation with waterproof connectors.
For warranty information and to register your product for warranty purposes, visit lightforce.com/warranty LIGHTFORCE AUSTRALIA PTY LTD 11 Manton Street, Hindmarsh SA 5007 Email: info@lightforce.com Telephone: (08) 8440 0888 www.lightforce.com All logos and images are subject to relevant trademark and copyright protection Lightforce Pty Ltd. Copyright © 2018. Data and specifications contained maybe subject to change without notice.
