User Manual

10
Troubleshooting
Problem Possible Cause
LED light burned out.
Power is off.
Faulty wire connection
Faulty switch Test and/or replace switch
Replace the LED Ceiling Light
Make sure power supply
is on. Ensure the circuit
breaker is in the on position
as well.
Check wiring to ensure all
wires are correctly wired
and are wired securely
Solution
Light does
not
illuminate
Light does
not turn on.
Fuse blows
or circuit
breaker trips
when light is
illuminated.
The wires are
crossed (not wired
properly)
or the power wire is
grounding out.
Turn power to the light off
from the breaker. Check the
wires to ensure the wires
were properly connected. If
everything looks correct,
contact a qualified
electrician to check your
wires.
11
吸顶灯安装说明书：尺寸：100x145mm 材质：128g双铜纸 风琴折
5
7
Screw Installation
The AC line comes out
through the hole.
Step A
Wall drilling and fixing
expansion pipe
Step B
The lamp panel is fixed
on the Ceiling by screws
Step C
9
Hardwire for EU
EU standard:
L—Live Line (Brown)
N—Null Line (Blue)
E—Earth Line(Yellow)
1
LED CEILING LIGHT
This LED Ceiling Light is suitable for any
indoor location (e.g. home, office, ware-
house, workshop, garage, and etc.).
Specifications
Input Voltage: 100-240V / 50-60Hz
Input Power: 18W / 24W
Max Luminous Flus: 1800LM / 2400LM
Color Temperature: 2700K-6500K
Color: RGB, Cool White, Warm White
Net Weight: 0.65 / 0.75kg
Gross Weight: 0.85 / 0.95kg
Dimension: 300mm / 400mm
Applicable Scene: bedroom, living room,
children's room
2
Important Safety Instructions
Please read the following safety information
before use.
To reduce risk of fire, electric shock, or injury
to persons:
• Turn OFF the main power at the fuse or
circuit breaker before installing the light
fixture or making any electrical connection.
• Make sure this light fixture is adequately
grounded. To ensure proper grounding, there
must be a separate ground wire (bare
copper) contact between this light fixture
and the ground connection of your main
power supply panel. Do not connect the bare
or green insulation fixture ground wire to the
black (hot) current-carrying wire or the
white(neutral) wire. Connection of the bare
or green fixture ground wire to the black or
white wires may cause metal parts of the
fixture to carry electrical currents, and may
cause electrical shock, which could cause
serious injury or death.
3
• Do not suspend any fixture by the house
wires. Suspending a fixture by the house
wires and wire connectors may result in the
fixture falling, possibly causing personal
injury and the danger of electrical shock or
fire.
• It is recommended that a qualified electri-
cian perform all wiring connections. All
electrical connections must be in accordance
with all national and local electrical codes.
• This light fixture is designed for a 100 –
240VAC, 50/60Hz fuse circuit. Not for use on
a dimming circuit.
• For indoor use only.
Installation Procedures
1.Rotate the cover anticlockwise to detach it
from the lamp body .
2.Fix the mounting cross bar to the junction box.
3.The AC line comes out through the inner key-
hole slots.
4.Tighten the short mounting screws to ensure
the lamp body is secured against the bracket.
5.AC Wire connections(L/N/E)
Make the following spliced wire connections
using wire nuts(US Standard).
• White (Neutral Line) supply wire to Blue light
fixture wire
• Black (Live Line) supply wire to Red light fixture
wire
• Green (Earth Line) supply wire to Yellow light
fixture wires
Tips: Another way through electroprobe to check
L / N / E line
High voltage: LIVE line
Low voltage: NULL line
Almost no volatge: Earth line
6.Attach the cover to the Lamp body, and rotate
the cover clockwise to secure in place.
Warning: Never connect the Ground/Earth Wire
to the black or white power supply wires.
4
12
Warning
• LED light output is strong enough to injure
human eyes. Precautions must be taken to
prevent looking directly at the LEDs without
installing the diffuser (cover) for more than a
few seconds.
• If the lighting light fixture is damaged, it
shall be exclusively replaced by the manufac-
turer or the service agent or qualified person
in order to avoid a hazard.
• Do not tamper with or attempt to repair the
LED component or fixture.
• The warnings, precautions, and instructions
discussed in this manual cannot cover all
possible conditions and situations that may
occur. The operator must understand that
common sense and caution are factors which
cannot be built into this product
• Do not install this LED with a dimmer.
Doing so may damage the driver inside if
used with a dimming circuit.
13
• This device does not have a plug; rewiring
is required. If you are unsure how to rewire
this light, please read the instruction or
contact a qualified electrician to install.
• Always shut the power from the fuse
(breaker) when conducting any type of main-
tenance on the light even after the LED
lifespan runs out.
Cleaning:
• Clean the outside of the fixture with a soft,
dry cloth or slightly dampened clean cloth.
Never use a cleaner with chemicals, solvents,
or harsh abrasives to clean the product.
Before Installation:
Please turn OFF the main power at the fuse
or circuit breaker before installing the light
fixture or making any electrical connection.
You may use a non-contact voltage tester to
ensure no power running to the wires.
Warning: Failure to disconnect the power
supply prior to installation may result in
serious injury or death.
6
Bracket Installation for US
Mounting cross bar on
the junction box
Step A
Step B
.The AC line comes out
through the inner keyhole
slots.
.Tighten the short mounting
screws to ensure the lamp
body is secured against the
bracket.
Smart Ceiling Light
Installation Guide
Contents
Specifications................................1
Safety Instructions....................2-3
Installation Procedures................4
Packing List....................................5
Bracket Installation for US...........6
Screw Installation..........................7
Hardwire for EU.............................8
Hardwire for US.............................9
Installation Preview......................10
Troubleshooting............................11
Warning....................................12-13
Packing List
Packing Included:
1 x LED Ceiling Light
4 x Long Mounting Screw
4 x Expansion Screw
1 x Mounting Cross Bar (US only)
2 x Short Mounting Screw (US only)
Mounting Cross Bar
Cover
Lamp Body
Long Mounting Screws
Expansion Screws
Short Mounting Screws
8
Hardwire for US
US standard:
L—Live Line (Black)
N—Null Line (White)
E—Earth Line(Green)
Null Line
Live Line
Earth Line