Owner's Manual

ManualsBrandsLiftMaster ManualsMisc ElectronicsLiftMaster T- Logic 4

BASIC PROGRAMMING

OPTN

PROG

DIAG

FSTS

Operation will

vary depending

on wiring type

SELECTOR DIAL

OPTN

PROG

DIAG

FSTS

To prevent possible SEVERE INJURY or DEATH:

• Install a LiftMaster Monitored Entrapment Protection (LMEP)

device.

• NEVER permit children to operate or play with door control

push buttons or remote controls.

• Activate door ONLY when it can be seen clearly, is properly

adjusted and there are no obstructions to door travel.

• ALWAYS keep door in sight until completely closed. NEVER

permit anyone to cross path of closing door.

ATTENTION

AVERTISSEMENT AVERTISSEMENT

AVERTISSEMENT

WARNING WARNING

CAUTION

WARNING

PRECAUCIÓN

ADVERTENCIA

ADVERTENCIA ADVERTENCIA

TIMER-TO-CLOSE

Feature: Timer automatically closes door after preset time. All

safety devices must be unobstructed.

Benefit: The door will automatically close after preset amount of

time. Great for apartment buildings, fire stations and other

applications where the end user wants the door to close

automatically after a specified amount of time.

Requirements: Must have at least one LiftMaster Monitored

Entrapment Protection (LMEP) device installed (refer to page 20).

Wiring type must be set to TS, T or FSTS.

TO PROGRAM MANUALLY (METHOD 1):

1. Close the door.

2. Turn the selector dial to PROGRAM.

3. Press and release the TIMER button on the logic board.

4. Press and release the STOP button to clear the timer.

5. Press and release the OPEN button for every second the

operator should wait before attempting to close the door. Press

and release the CLOSE button for every 15 seconds the

operator should wait before closing the door.

6. Press and release the TIMER button to complete programming.

The OPEN/CLOSE button LEDs will flash to confirm the timer

setting. The OPEN LED will flash once for every second

programmed and the CLOSE LED will flash once for every 15

seconds programmed.

7. Turn the selector dial to desired timer wiring type (TS ,T or

FSTS).

Example: To close the door after 70 seconds. Turn selector dial to

PROGRAM, press and release the TIMER button, press and

release the STOP button to clear the timer, press and release the

CLOSE button four times for 60 seconds and press and release

the OPEN button 10 times for 10 seconds. Press the TIMER

button to finish programming the timer. Turn selector dial to

desired timer wiring type. (TS, T, FSTS).

PROGRAM TIMER-TO-CLOSE BY EXAMPLE (Method 2):

TO PROGRAM:

1. Close the door.

2. Turn the selector dial to PROGRAM.

3. Press and hold TIMER button for 5 seconds until OPEN and

OLS flashes then release.

4. Press and release the OPEN button and wait for the door to

reach full open or mid stop position.

5. Wait for desired amount of time to pass. (An internal stop

watch starts counting when the door stops moving.)

6. Press and release the TIMER button, CLOSE button or STOP

button to stop the timer. (TIMER SET LED will turn on.)

7. Turn the selector dial to the desired wiring type (T, TS, FSTS).

NOTE: To read back the Timer-To-Close setting, turn the selector

dial to DIAGNOSTIC and press the TIMER button. The OPEN LED

will flash once for every second programmed and the CLOSE LED

will flash once for every 15 seconds programmed.

To deactivate the timer from the open position press the STOP

button. The timer will be reactivated on the next operation

command. To deactivate the timer for more than one cycle, attach

a switch to 11 and 12 (Common and Timer Defeat).

Reminders: FSTS wiring mode allows the Timer-To-Close to be

activated by the Single Button Control (terminal 1) only. T wiring

mode allows the door to attempt to close only one time for safety

purposes.

OPTN

PROG

DIAG

FSTS

Operation will vary

depending on wiring type

SELECTOR DIAL

OPTN

PROG

DIAG

FSTS