Owner's Manual
OPEN
OPEN
CLOSE
OPE
N
O
PEN
C
LO
SE
OP
E
N
OPENO
P
E
N
CLOSEC
L
O
S
E
OP
E
N
O
P
E
N
C
L
O
S
E
OPEN
CLOSE
STOP
OPENOP
E
N
O
P
E
N
C
L
O
S
E
OPE
N
O
PEN
C
LO
SE
OP
E
N
O
P
E
N
C
L
O
S
E
373LM
371LM
65-8202
65-5202
3-Button SECURITY✚
®
Remote Control:
Includes visor clip.
1-Button SECURITY✚
®
Remote Control:
Includes visor clip.
Vehicle Detection System:
Pneumatic Sensing Edge Kit with exterior air switch, 2-wire
coil cord and 14' air hose.
Vehicle Detection System:
Pneumatic Sensing Edge Kit with exterior air switch, 2-wire
take-up reel (20' extended) and 14' air hose.
OPEN
O
PEN
C
LO
SE
333LM
3-Button Tri-Colored Dip Switch Remote Control:
Includes visor clip.
2-Button Control Station:
Steel enclosure.
1-Button Control Station:
Steel enclosure.
Commercial Protector System
®
:
Provides protection on doors up to 45' wide. NEMA-4
rated.
CPS-UN4
3-Button Control Station:
Steel enclosure with Maintenance Alert System.
02-103L
OPEN
OPEN
CLOSE
Commercial Protector System
®
:
Provides protection on doors up to 30' wide.
CPS-U
OP
EN
O
P
E
N
C
L
O
S
E
OP
EN
O
P
E
N
C
L
O
S
E
ENTRAPMENT PROTECTION DEVICES
REMOTE CONTROLS 315MHz
CONTROL STATIONS
02-102
02-101
ACCESSORIES
CPS-EI
Monitored Safety Edge Interface:
For use with the approved 4-wire safety edge (see below).
OPEN
OPEN
CLOSE
40-34141-1
LMEP2
LMEP1
E1
E2
E3
E4
CPS-EI
OP
E
N
O
P
E
N
C
L
O
S
E
OPEN
STOP
CLOSE
Key Control Station:
Indoor flush mount, NEMA 1 with Stop button.
02-110
Timer Light Status Card:
The TLS option card provides special functionality to
activate and flash auxiliary devices such as lights, bells, and
horns/strobes at various door positions, and to provide
special timer functions.
TLSCARD
Auxiliary Contact Card:
The Auxiliary Contact option card has both Normally-Open
and Normally-Closed contacts that actuate when the door is
idle, opening, or closing.
AUXCARD
65ME1234
Miller ME123 4-Wire Monitored Safety Edge:
For sectional or rolling doors.
65ME123C
U-Shaped Mounting Channel:
For 65ME1234 edge when installed on sectional doors.
65ME123C1
T-Shaped Mounting Channel:
For 65ME1234 edge when installed on rolling doors. Fits
between L-shaped angles used to construct a bottom bar
on rolling doors.
65ME123CA3
L-Shaped Mounting Channel:
For 65ME1234 edge when installed on sectional doors.
65ME110
Miller ME110 4-Wire Monitored Safety Edge:
For rolling grilles and counter shutters.
Cast iron bracket to mount J, H, DH, DJ, and GH side mount
operators on end bracket of a rolling door or grill. For
vertical or horizontal mount on either front or top of coil.
Heavy gauge steel bracket for vertical or horizontal mount
on either front or top of coil on a rolling door. Has a variety
of mounting hole patterns compatible with many OEM
manufacturers. May be welded. For use with J, H, DJ, and
DH operators.
08-9098
MOUNTING BRACKETS
OP
E
N
O
P
E
N
C
L
O
S
E
OPEN
OPEN
CLOSE
10-12360
Same as 08-9098, but with adapter plate to hold mounting
bolt holes in place for ease of use.
Heavy gauge steel bracket for vertical or horizontal mount
on either front or top of coil on a rolling door. May be
welded. For use with J, H, DJ, and DH operators.
Same as 1A4324, but with adapter plate to hold mounting
bolt holes in place for ease of use.
08-9098EZ
1A4324
1A4324EZ
OP
EN
O
P
EN
C
LO
SE
Operator Cover:
For use with wall-mounted J, H, GH, DH or DJ operators.
Measures 31" x 19" x 18" (L x W x D). Assembly required.
Recommended for damp environments where direct spray
is present. Required when the operator is installed less
than 8 feet above the floor.
1A3982
OP
E
N
O
P
E
N
C
L
O
S
E
Antenna Extension Kit:
The antenna extension kit can be used with EXT-ANT for
maximum radio receiver range.
86LM (15')
86LMT (25')
MISCELLANEOUS
For 1" shafts. Recommended to properly tension drive chain
between operator shaft and door shaft.
71-6023
71-6125
Same as 71-6023, but for 1-1/4" shafts.
For Jackshaft Type Operators
CHAIN TENSIONERS
MOUNTING CHANNELS
CPS3
Option Logic Board:
For use when more than one set of photoelectric eyes are
required.
MONITORED
NON-MONITORED
OP
E
N
O
PE
N
C
L
O
S
E
11