Logic 3 OWNER’S MANUAL J H HJ INDUSTRIAL DUTY COMMERCIAL DOOR OPERATOR IN T ENA N C L E PAT E N T P E N D I N G R T SYS E A M E M A This Operator Features the Enhanced T The Maintenance Alert System™ allows the installer to set an internal Maintenance Cycle Counter. The Logic 3 operator incorporates a self-diagnostic feature built into the (MAS) Maintenance Alert System LED.
TABLE OF CONTENTS SPECIFICATIONS Carton Inventory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Operator Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Operator Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Programming Remotes . . . . . . . . . . . . . . . . . . . . . . . . . . . .18-19 Maintenance Alert System (MAS) . . . . . . . . . . . . . . . . . . . . . . .20 Mid Stop . . . . . . . . . . . . . . . . . . . . .
CARTON INVENTORY Before beginning your installation check that all components were provided. DESCRIPTION POWERHEAD ASSEMBLY OWNER’S MANUAL AND CAUTION LABELS HARDWARE BOX (INCLUDES FASTENERS, DISCONNECT AND CHAIN HOIST WALL BRACKET) 3-BUTTON CONTROL STATION WITH LED HOIST HAND CHAIN (MODELS H & HJ ONLY) DOOR SPROCKET DOOR/OPERATOR DRIVE CHAIN O P E R AT O R D I M E N S I O N S WEIGHTS AND DIMENSIONS HANGING WEIGHT: MOUNTING DIMENSIONS A - Wall Mounting B - Bracket Mounting (rolling door) 80-110 LBS.
O P E R AT O R S P E C I F I C AT I O N S MOTOR ELECTRICAL TYPE:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Continuous Duty HORSEPOWER: . . . . . . . . . . . . . . . . . . . 1/3, 1/2, 3/4 and 1 HP SPEED: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1725 RPM VOLTAGE:. . . . . . . . . . . . . . . . . . . . . . . . . . . 115/230V 1 Phase, 208/230/380/460/575V 3 Phase CURRENT: . . . . . . . . . . . . . . . . . . . . . . . . See Motor Nameplate TRANSFORMER: . . . .
WARNING P R E PA R AT I O N It is imperative that the wall or mounting surface provide adequate support for the operator. This surface must: a. Be rigid to prevent play between operator and door shaft. b. Provide a level base. c. Permit the operator to be fastened securely and with the drive shaft parallel to the door shaft. CAUTION WARNING WARNING To prevent possible SERIOUS INJURY or DEATH: • DO NOT connect electric power until instructed to do so.
I N S TA L L AT I O N IMPORTANT NOTE: Before your operator is installed, be sure the door has been properly aligned and is working smoothly. The operator may be wall mounted or mounted on a bracket or shelf. If necessary, refer to the preparation on page 5. Refer to the illustrations and instructions below that suit your application. Figure 1 MOUNT THE OPERATOR 1. Wall Mount: The operator should generally be installed below the door shaft, and as close to the door as possible (Figure 1).
I N S TA L L AT I O N MANUAL OPERATION WARNING This operator has provisions for manually operating the door in case of emergency or power failure. To prevent possible SERIOUS INJURY from a moving chain, ENGAGE interlock BEFORE manually operating your door. CAUTION MODEL H These operators are equipped with a manual hoist. An electrical interlock will disable the electrical controls when the hoist is used. To operate the hoist: Chain Keeper (with pad locking provisions) 1.
I N S TA L L AT I O N ENTRAPMENT PROTECTION ACCESSORIES (OPTIONAL) WARNING To reduce the risk of SEVERE INJURY or DEATH, ALWAYS install reversing sensors when the 3-button control station is out of sight of door or ANY other control (automatic or manual) is used. Reversing devices are recommended for ALL installations. PHOTO EYES & SENSING EDGES Sensing devices provided for door industry type operators with an isolated normally open (N.O.) dry contact output are compatible with your operator.
ADJUSTMENT BRAKE ADJUSTMENT A solenoid brake is available as an option (not included as a standard feature). The brake is adjusted at the factory and should not need additional adjustment for the the life of the brake assembly. Brake Assembly Replace brake assembly when necessary. Refer to the illustration for identification of components for the solenoid type brake system.
NING WARNING POWER WIRING & GROUND WIRING ION WARNING To reduce the risk of SEVERE INJURY or DEATH: • ANY maintenance to the operator or in the area near the operator MUST NOT be performed until disconnecting the electrical power and locking-out the power via the operator power switch. Upon completion of maintenance the area MUST be cleared and secured, at that time the unit may be returned to service. • Disconnect power at the fuse box BEFORE proceeding.
C O N T R O L S TAT I O N W I R I N G & I N S TA L L AT I O N CONTROL WIRING CONNECTIONS WARNING 1. Connect control wires to the P1 terminal block located on the logic board as shown. 2. Connect conduit with all control wires through the conduit hole in the electrical box enclosure marked with the label shown below. To prevent possible SERIOUS INJURY or DEATH, install reversing sensors when the 3-button control station is out of sight of the door or ANY other control (automatic or manual) is used.
STANDARD POWER & CONTROL CONNECTION DIAGRAMS OPEN Maintenance Alert LED (RD) R3 Radio Control (24V DC only) CLOSE (WH) STOP R2 Open R1 3-Button Station Close Sensing Edge Stop CPS-L & CPS-LN4 Open/Close Single Button Timer Defeat Switch Remove Jumper To Install External Interlock Single Phase Power Wiring Line Power 115/230 Vac Single Phase Three Phase Power Wiring Phase 1 Hot Line Power 208/230/380/460/575 Vac Three Phase Neutral Gnd Phase 2 Phase 3 Gnd 12
LOGIC (VER. 3.0) 1 PHASE WIRING DIAGRAM OPEN Maintenance Alert LED (RD) (WH) CLOSE STOP Open 230V MOTOR CONNECTION Close Sensing Edge NOTE: Gray (GY) and purple (PU) motor wires are reversed for H and HJ right hand models and all GH and J models.
LOGIC (VER. 3.0) 3 PHASE WIRING DIAGRAM (BR) (YE) J T9 T3 (GY) (BR) 2 (PU) 3 (BR) (YE) OPEN Maintenance Alert LED (RD) (WH) (BL/BK) 460V MOTOR CONNECTION STOP 575V MOTOR CONNECTION NOTE: Gray (GY) and purple (PU) motor wires are reversed for H and HJ right hand models and all GH and J models.
LOGIC BOARD R31 Ø14LGØ657–A Ø14GPØ657–A P4 C3Ø D8 E1 C18 U7 Auxilliary Board Connectors Motor Direction Jumper D31 R29 D7 D6 C11 D5 D3Ø2 P1Ø X1 U1 K3 C25 C17 POWER Programmed Chip D4 Single Phase & Three Phase Jumper 24V AC 14 24V AC 13 D19 J3ØØ D26 CLS D27 SLS D16 TIMER DEFEAT 12 TIMER DEFEAT SINGLE PHASE D24 STD MID CONTACTOR/3 PH D25 MOTOR DIRECTION Maximum Run Timer Button OLS REV J1 R8 D17 MAS D28 4 D23 EYES CMN 11 MAS 10 EYES 9 EDGE 8
PROGRAMMING LOGIC CONTROL PUSHBUTTONS OPEN, CLOSE, STOP SELECTOR DIAL Open, Close and Stop buttons are mounted directly on the logic board. Thus, making it easy to program as well as have door control at the electrical box. Either the stop control or a jumper must be wired between terminals 4 and 5 for the on board push buttons to function. NOTE: Refer to logic board illustration on page 15 for all component locations. Before programming the logic board, set the operators open and close limits.
PROGRAMMING FAILSAFE WIRING TYPES TYPE TS T FSTS Momentary contact to open, close, and stop with open override and Timer To Close. Every device that causes door to open, including a reversing device, activates the Timer To Close. Auxiliary controls can be connected to open input to activate the Timer To Close. If the timer has been activated, the open button and radio control can recycle the timer. The stop button will deactivate the Timer To Close until the next command input.
PROGRAMMING Built in 3-channel, 315MHz radio receiver allows you to add as many as 23 Security✚® remotes or dip switch remote controls. WARNING PROGRAMMING REMOTES To prevent possible SERIOUS INJURY or DEATH, install reversing sensors when the 3-button control station is out of sight of the door or ANY other control (automatic or manual) is used. Reversing devices are recommended for ALL installations. STANDARD SINGLE BUTTON REMOTE 1.
PROGRAMMING Your 315MHz Security✚®or dip switch remote control can be programmed to operate as a 3-button wireless control station: the large button will open the door, the middle button will close the door, and the third button will stop the door’s movement. You may set up this feature as follows: 1. To enter programming press the RADIO button on the logic board (the RADIO LED will light). 2. To program the OPEN button to a remote control press the OPEN button on the logic board.
PROGRAMMING SELECTOR DIAL MAINTENANCE ALERT SYSTEM (MAS) Feature: An internal cycle counter will activate a flashing LED on the 3-button control station when the preset number of cycles or months has elapsed (whichever occurs first). Setting this feature is optional. By default this feature will never activate. Logic 3.0 operators incorporate a self diagnostic feature built into the MAS LED.
