CONTROL CONNECTION DIAGRAM FACTORY SET IMPORTANT NOTES: 1) The 3-Button Control Station provided must be connected for operation. 2) If a STOP button is not used, a jumper must be placed between termianls 3 and 4. 3) Auxiliary control equipment may be any normally open two wire device such as pullswitch, single button, loop detector, card key or such device. C2 Wiring ATTENTION ELECTRICIAN: USE 16 GAUGE OR HEAVIER WIRE FOR ALL CONTROL CIRCUIT WIRING.
SPECIFICATIONS MOTOR OPERATOR NOTES ELECTRICAL TYPE: ....................................AC Synchronous continuous duty brake motor TRANSFORMER: ...............3PH: 208/230/480 VAC 24VAC OR 3PH: 575VAC-24VAC CONTROL STATION: ........NEMA 1 three button station. OPEN/CLOSE/STOP ENCLOSURE:.......................ODP NEMA 184TC face mount. WIRING TYPE: ...................
OPERATOR NOTES IMPORTANT SAFETY NOTES CAUTION WARNING WARNING TO AVOID DAMAGE TO DOOR AND OPERATOR, MAKE ALL DOOR LOCKS INOPERATIVE. SECURE LOCK(S) IN "OPEN" POSITION. IF THE DOOR LOCK NEEDS TO REMAIN FUNCTIONAL, INSTALL AN INTERLOCK SWITCH. DO NOT CONNECT ELECTRIC POWER UNTIL INSTRUCTED TO DO SO. KEEP DOOR BALANCED. STICKING OR BINDING DOORS MUST BE REPAIRED. DOORS, DOOR SPRINGS, CABLES, PULLEYS, BRACKETS AND THEIR HARDWARE MAY BE UNDER EXTREME TENSION AND CAN CAUSE SERIOUS PERSONAL INJURY.
ILLUSTRATED PARTS – MODEL GH 5HP OPERATOR MOUNTING Before your operator is installed, be sure the door has been properly aligned and is working smoothly. The operator may be wall mounted or mounted on a bracket or shelf. If necessary, refer to the operator preparations on page 3. Refer to the illustration and instructions below that suits your application. NOTE: The operator has a weight of 300 lbs. 1a.
REPAIR PARTS KITS – MODEL GH 5HP Refer to the parts lists below for replacement kits available for your operator. If optional modifications and/or accessories are included with your operator, certain components may be added or removed from these lists. Individual components of each kit may not be available. Please consult a parts and service representative regarding availability of individual components. Refer to page 11 for all repair part ordering information.
ILLUSTRATED PARTS – ELECTRICAL BOX ENTRAPMENT PROTECTION ACCESSORIES (OPTIONAL) SENSING EDGES All types of sensing edges with an isolated normally open (N.O.) output are compatible with your operator. This includes pneumatic and electric edges. If your door does not have a bottom sensing edge and you wish to purchase one, contact the supplier of your operator. IT IS STRONGLY RECOMMENDED THAT A SENSING EDGE OR OTHER ENTRAPMENT PROTECTION DEVICE BE USED IN CONJUNCTION WITH THIS OPERATOR.
REPAIR PARTS KITS – ELECTRICAL BOX POWER WIRING CONNECTIONS Below are replacement kits available for your operator. For replacement of electrical box, motor or brake components be sure to match model number of your unit to kit number below to ensure proper voltage requirements. Optional modifications and/or accessories included with your operator may add or remove certain components from these lists.
CONTROL WIRING THREE PHASE FIELD WIRING DETERMINE WIRING TYPE Refer to the wiring diagram located on the inside cover the electrical box to determine the type of control wiring. Standard C2 or B2 Wiring Standard operators are shipped from the factory with jumper set for C2 wiring, which requires constant pressure on button to close the door. If momentary contact on close direction is desired (B2 wiring) you must include an entrapment protection device. See close control jumper setting below.
THREE PHASE SCHEMATIC DIAGRAM 1942 CONTROL WIRING (con’t) Radio Controls On all models with type B2 control wiring, a terminal block marked R1 R2 R3 is located in the inside of the electrical enclosure. All standard radio control receivers may be used. The operator will then open a fully closed door, close a fully open door, and reverse a closing door from the radio transmitter.
CONNECT REVERSING EDGE DEVICE (OPTIONAL) The operator has been pre-wired to accept connection of a reversing edge device. Connect the normally open contacts to terminals T4 and T8 on the low voltage terminal block. A cut-off switch will deactivate the safety device during the last few inches of the door's downward travel. MAINTENANCE SCHEDULE Check at the intervals listed in the following chart.
CONNECT REVERSING EDGE DEVICE (OPTIONAL) The operator has been pre-wired to accept connection of a reversing edge device. Connect the normally open contacts to terminals T4 and T8 on the low voltage terminal block. A cut-off switch will deactivate the safety device during the last few inches of the door's downward travel. MAINTENANCE SCHEDULE Check at the intervals listed in the following chart.
THREE PHASE SCHEMATIC DIAGRAM 1942 CONTROL WIRING (con’t) Radio Controls On all models with type B2 control wiring, a terminal block marked R1 R2 R3 is located in the inside of the electrical enclosure. All standard radio control receivers may be used. The operator will then open a fully closed door, close a fully open door, and reverse a closing door from the radio transmitter.
CONTROL WIRING THREE PHASE FIELD WIRING DETERMINE WIRING TYPE Refer to the wiring diagram located on the inside cover the electrical box to determine the type of control wiring. Standard C2 or B2 Wiring Standard operators are shipped from the factory with jumper set for C2 wiring, which requires constant pressure on button to close the door. If momentary contact on close direction is desired (B2 wiring) you must include an entrapment protection device. See close control jumper setting below.
REPAIR PARTS KITS – ELECTRICAL BOX POWER WIRING CONNECTIONS Below are replacement kits available for your operator. For replacement of electrical box, motor or brake components be sure to match model number of your unit to kit number below to ensure proper voltage requirements. Optional modifications and/or accessories included with your operator may add or remove certain components from these lists.
ILLUSTRATED PARTS – ELECTRICAL BOX ENTRAPMENT PROTECTION ACCESSORIES (OPTIONAL) SENSING EDGES All types of sensing edges with an isolated normally open (N.O.) output are compatible with your operator. This includes pneumatic and electric edges. If your door does not have a bottom sensing edge and you wish to purchase one, contact the supplier of your operator. IT IS STRONGLY RECOMMENDED THAT A SENSING EDGE OR OTHER ENTRAPMENT PROTECTION DEVICE BE USED IN CONJUNCTION WITH THIS OPERATOR.
REPAIR PARTS KITS – MODEL GH 5HP Refer to the parts lists below for replacement kits available for your operator. If optional modifications and/or accessories are included with your operator, certain components may be added or removed from these lists. Individual components of each kit may not be available. Please consult a parts and service representative regarding availability of individual components. Refer to page 11 for all repair part ordering information.
ILLUSTRATED PARTS – MODEL GH 5HP OPERATOR MOUNTING Before your operator is installed, be sure the door has been properly aligned and is working smoothly. The operator may be wall mounted or mounted on a bracket or shelf. If necessary, refer to the operator preparations on page 3. Refer to the illustration and instructions below that suits your application. NOTE: The operator has a weight of 300 lbs. 1a.
OPERATOR NOTES IMPORTANT SAFETY NOTES CAUTION WARNING WARNING TO AVOID DAMAGE TO DOOR AND OPERATOR, MAKE ALL DOOR LOCKS INOPERATIVE. SECURE LOCK(S) IN "OPEN" POSITION. IF THE DOOR LOCK NEEDS TO REMAIN FUNCTIONAL, INSTALL AN INTERLOCK SWITCH. DO NOT CONNECT ELECTRIC POWER UNTIL INSTRUCTED TO DO SO. KEEP DOOR BALANCED. STICKING OR BINDING DOORS MUST BE REPAIRED. DOORS, DOOR SPRINGS, CABLES, PULLEYS, BRACKETS AND THEIR HARDWARE MAY BE UNDER EXTREME TENSION AND CAN CAUSE SERIOUS PERSONAL INJURY.
SPECIFICATIONS MOTOR OPERATOR NOTES ELECTRICAL TYPE: ....................................AC Synchronous continuous duty brake motor TRANSFORMER: ...............3PH: 208/230/480 VAC 24VAC OR 3PH: 575VAC-24VAC CONTROL STATION: ........NEMA 1 three button station. OPEN/CLOSE/STOP ENCLOSURE:.......................ODP NEMA 184TC face mount. WIRING TYPE: ...................
CONTROL CONNECTION DIAGRAM FACTORY SET IMPORTANT NOTES: 1) The 3-Button Control Station provided must be connected for operation. 2) If a STOP button is not used, a jumper must be placed between termianls 3 and 4. 3) Auxiliary control equipment may be any normally open two wire device such as pullswitch, single button, loop detector, card key or such device. C2 Wiring ATTENTION ELECTRICIAN: USE 16 GAUGE OR HEAVIER WIRE FOR ALL CONTROL CIRCUIT WIRING.
