Owner’s Manual WALL MOUNT FIREPLACE HW93233SMQR IMPORTANT SAFETY INFORMATION: Always read this manual first before attempting to install or use this stove. For your safety，always comply with all warnings and safety instructions contained in this manual to prevent personal injury or property damage.
Table of Contents Important Instructions...............................................3 Warranty ..................................................................... 4 Pre-Assembly............................................................. 5 Hardware Included ................................................... 5 Product S ............................................... 5 Tools Required ......................................................... 5 Package Contents...........................................
Important Instructions When using electrical appliances,basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following: ① Read all instructions before installing or using this heater. ② This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. Keepcombustible materials, such as furniture, pillows, bedding, papers, clothes, etc. and curtains at least 3 feet ( 0.
Warranty 4
Pre-Assembly HARDWARE INCLUDED AA BB DD EE Part Description CC FF Part Number Quantity AA AnchorScrew 180000010600 5 BB Wall Anchor 300000190100 5 CC Screw 4mm x 8mm 180000010100 1 DD Inner hexagonal bolt M4mmx10mm XXXXXXXXXX 12 EE Outer hexagonal nut M4mm 12 FF Inner hexagonal bolt Tool XXXXXXXXXX XXXXXXXXXX 1 NOTE: Hardware not shown to actual size. PRODUCT SPECIFICATIONS Voltage 120 VAC, 60Hz Amps 12.
Pre-Assembly (continued) PACKAGE CONTENTS B A C D E F G H I J K NOTE: The scale and size of parts may be different depending on your exact model.
Installation Operation - Wall Hanging Hanging on a wall Your new electric fireplace may be installed virtually somewhere in your home. However, when choosing a location be sure to follow the general instructions included. For best results install out of direct sunlight. Power supply service must be either completed or placed within the electric fireplace prior to finishing to avoid reconstruction. Min. 60 cm 24 in. Min. 5 cm 2 in. Min. 5 cm 2 in. Min. 5 cm 2 in.
Installation - Wall Mounting Operation 1 2 Choosing a Wall Location Choose a wall location to attach the Mounting Bracket (B). Position the Mounting Bracket (B) in the desired location. Use a level to align the bracket and mark the four holes with a pencil. Drilling the Holes Drill five 7/25 in. (7 mm) holes in the wall. Insert the Wall Anchors (BB) into the holes using a hammer. Use the two marked center holes of the Top Mounting Bracket (B) to measure and locate the hole for the Bottom Bracket (A).
Installation - Wall Mounting (continued) Operation Operation 5 Hanging the Fireplace Hang the Fireplace (C&D) on the hook at the top of the Top Mounting Bracket (B) and let the Fireplace (C&D) sit onto the Bottom Mounting Bracket (A).
Installation - Wall Mounting (continued) Operation Operation 6 Securing the Fireplace Secure the fireplace (C&D) to the Bottom Mounting Bracket (A) with the retaining Screw (CC). Continue to the fuel bed setup instructions (Page 15).
Fuel Bed Setup Instructions Operation 1 Removing the Frame Remove the four screws that attach the Frame (D) to the Fireplace (C) and remove the Frame (D). C D 2 Placing the Logs and media pieces Place the Crystal Media Pieces (J) on the Fuel bed. Place the Logs Media(I) on the Crystal Media Pieces (if need a Log effect view). Place the Frame (D) back on the Fireplace (C) with the four screws removed in Step 1.
Metal Frame Setup Instructions Operation 1 The Wall Fire provided 2 Frames options, it can be Frame option either front glass or Metal Frame, the Metal Frame is covering the front glass when it was fixed. Jointing and Securing the Trims Take one Horizontal Trim (E) and one Longitudinal Trim (F), joint and align the 3 holes on the edges. Insert Inner hexagonal bolt (DD) to go through the aligned holes, secure the Outer hexagonal nut (EE) on the bolt by using provided Tool (FF).
Metal Frame Setup Instructions (Continued) Operation 3 Removing the fitting screws on Fireplace 4 Hooking the Metal Frame Remove 4 screws on the fireplace (2screws on top and 2 on the bottom). Put and hook top flange onto the fireplace top. Push and hook the Frame bottom.
Metal Frame Setup Instructions (Continued) Operation 5 Securing the screws onto the Fireplace Secure Removed 4 screws back on the fireplace (2screws on top and 2 on the bottom).
Operation Operation Display Control Panel T 4. Thermostat up button 1. Power Button 4. Thermostat Down button 3. Heater Button 2. Flame effect button 4. Thermostat Down button 3. Heater Button 4. Thermostat up button 7. Color themes button 5. Brightness button 7. Color themes button 6.
Operation (continued) Operation 2 Adjusting the Flame Effect 1 Powering the Fireplace Push the Power button to supply power to all functions of the fireplace and put the wall fire in a standby mode. Turns the Flame Effect On and Off, actived by pressing the button on the remote. Cycles the unit through the four settings: Push the Power button again to turn off all functions. ‘FE’, Flame and Fuel bed ON. ‘F-’, Flame ON, Fuel bed OFF. ‘-E’, Flame OFF, Fuel bed ON. ‘--’, Flame and Fuel bed OFF.
Operation (continued) Operation 7 Adjusting the Color Themes Press the Themes button on the control panel or remote control to change the Color Themes. There are 8 settings: OFF, Red, Sky Blue,Orange, Blue, Purple, Green and Cycling as indicated on the Display: 1-OFF 2-Red 3-Sky Blue 4-Orange 5-Blue 6-Purple 7-Green 8-Cycle from 2 to 7. NOTE: 8 Using the Power Cord Correctly This heater is for use on 120 volts. The cord has a plug as shown in the figure. Connect to properly grounded outlets only.
Care and Cleaning Clean the metal trim using a soft cloth, slightly dampened with a citrus oil-based product and buff with a soft, clean cloth. DO NOT use brass polish or household cleaners as these products will damage the metal trim. Purchase citrus oil-based products at a hardware store. WARNING: Make sure the power is turned off before proceeding with repairs. Any electrical repairs or rewiring of this unit should be carried out by a licensed electrician in accordance with national and local codes.
Troubleshooting PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION Display shows “ ”. front U The thermostat sensor is broken that the thermostat is plugged into the main circuit board. If this does not or disconnected. solve the problem contact customer service for a replacement thermostat sensor. Display shows “ ”. The thermostat sensor is broken. Contact customer service for a replacement thermostat sensor. Manual Reset overheat protection has triggered.
Replacement Parts For replacement parts, call our customer service department at 1-800-986-3460, 8 a.m.-7 p.m., EST, Monday-Friday, 9 a.m. - 6 p.m., EST, Saturday. Part Description Part Number Qty.
