Owner’s Manual HF9309BLQR-M40 IMPORTANT SAFETY INFORMATION: ety, always comply with all warnings and safety instructions contained in this manual to prevent personal injury or property damage.
Table of Contents IMPORTANT INSTRUCTIONS . . . . . . . . . . . . . . . . . 3 Fireplace Installation . . . . . . . . . . . . . . . . . . . . . . . . 5 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Trouble Shooting . . . . . . . . . . . . . . . . . . . . . . . .14 Replacement Parts . . . . . . . . . . . . . . . . . . . . . .
IMPORTANT INSTRUCTIONS When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following: ① Read all instructions before installing or using this heater. ⑤ Do not use outdoors. ⑥ To disconnect heater, turn controls to off, and then remove plug from outlet. ⑦ Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or damage the heater.
IMPORTANT INSTRUCTIONS ⑫ Do not burn wood or other vibration and store so as to avoid damage. ⑬ Do not strike the front glass. WARNING: Remote control contains a small battery. Keep away from children. If swallowed, seek medical attention immediately. ⑭ cian should new circuits or outlets be required. ⑮ Always use properly grounded, fused and polarized outlets. ⑯ Disconnect all power supply before performing any cleaning, maintenance or relocation of the heater.
Fireplace Installation WARNING: Ensure the power cord is not installed so that it is pinched or against a sharp edge and ensure that the power cord is stored or secured to avoid tripping or snagging to reduce the risk of sons. WARNING: Construction and electrical outlet wiring must comply with local building codes and other applicable regulations to reduce the to persons. WARNING: Do not attempt to wire your own new outlets or electric shock or injury to persons, always use a licensed electrician.
Fireplace Installation WHAT’S IN THE BOX 1 2 5 6 3 7 8 4 9 NOTE: Hardware not shown to actual size. Ref. Description Quantity 1 Fireplace HF9309BLQR-M40 1pc 2 Top Panel (A) 1pc 3 Front Frame (B) 1pc 4 Side Frame (C) 2pcs 5 3 in 1 Blot (DD) 14pcs 6 3 in 1 Cam (EE) 14pcs 7 Remote control 1pc 8 AAA Batteries 9 Owner’s Manual 1set(2pcs) 1pc PLANNING ASSEMBLY Before beginning assembly of product, make sure all parts are present.
Fireplace Installation WARNING: This product must be installed correctly, failure to do so may result in injury, electric shock to the user or damage to your product and your Property. Tools Required for Assembly (not included): Phillips Screwdriver BEFORE YOUR FIRST USE: 1. Remove your appliance from the packaging. 2. Install your appliance in accordance with the installation & safety instructions. 3. Your appliance is now ready for normal use. Dispose of the packaging in a responsible manner.
Fireplace Installation 3. Put the Side Frames (C) in place, place the 3 in 1 Cam (EE) in place and secured them. C EE 4. Secure the 3 in 1 Bolts (DD) into Fireplace top. Fireplace 5. Place the top Assembly finished on Step 3 onto fireplace top. Ensure all the bolts are fully inserted into the holes, put the 3 in 1 Cams (EE) into and secured.
Operation Display Figure 3 ControlPanel 6. Timer button 4. Thermostat up 4. Thermostat Down 3. Heater Button 1. Power Button T WARNING: This electric before it is used. The unit can be controlled by either the manual controls which are located on the upper right of Remote Control 1. Power Button 4. Thermostat up 3 & 4). 4. Thermostat Down 2. Flame effect button IR multifunction remote control. This remote control has a range of approximately 16 ft (5 m).
Operation（Continued） 1 Powering the Fireplace When appliance is Off: 1 press-Puts appliance into Standby Mode. 2 presses-Turns appliance on. When appliance is On: 1 press-Turns appliance off. 2 Adjusting the Flame Effect Turns the Flame Effect On and Off, actived by pressing the button on the remote. Cycles the unit through the four settings: ‘FE’, Flame and Fuel bed ON. ‘F-’, Flame ON, Fuel bed OFF. ‘-E’, Flame OFF, Fuel bed ON. ‘--’, Flame and Fuel bed OFF.
Operation Resetting the Temperature Cutoff Switch Should the heater overheat, an auto-matic cut out will turn the heater off and it will not come back on without being reset. It can be reset by unplugging the unit and waiting 30 minutes before plugging the unit back in. CAUTION: “E3” is on Display Once cut out is tripping. CAUTION: If you need to continuously reset the heater, unplug the unit and call technical support.
Maintenance WARNING: Disconnect power before attempting any maintenance or cleaning to shock or damage to persons. Glass Cleaning The glass is cleaned in the factory during the assembly operation. During shipment, installation, handling, etc., the front glass panel may collect dust particles; these can be removed by dusting lightly with a clean dry cloth. marks, the front glass panel can be cleaned with a damp cloth.
Warranty 13
Trouble Shooting PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION Display shows “ ”. front U The thermostat sensor is broken that the thermostat is plugged into the main circuit board. If this does not or disconnected. solve the problem contact customer service for a replacement thermostat sensor. Display shows “ ”. The thermostat sensor is broken. Contact customer service for a replacement thermostat sensor. ”. Manual Reset overheat protection has triggered.
Replacement Parts For replacement parts, call our customer service department at 8 a.m.-7 p.m., EST, Monday-Friday, 9 a.m. - 6 p.m., EST, Saturday. Part A Description Part Number Remote Control - 8 Buttons HF9309BLQR-M40-A Qty.
