OW NERS INSTALLATION AND OPERATING MANUAL LIFESMART INFRARED HEATER Model: LS-6BPIQH-X Safety Notice Please read this entire Installation and Operating Manual BEFORE installing and using your new Infrared Heater. Failure to fully understand and follow instructions may result in property damage, bodily injury, or even death. If the Infrared Heater in not used properly, a house fire may result. For everyone’s safety, FOLLOW all Installation and Operating Directions.
TABLE OF CONTENTS Topic Page(s) Customer Service & Support 3 Introduction & Specifications 4 Important Safety Information 5-7 Frequently Asked Questions 8-11 Heater Operation 12 Heater Placement 13 Users Guide 14-15 Air Filter Maintenance 16 Warranty 17-19 *Contents in the box: 1. Infrared heater (1unit) 2. Instruction manual (1pcs) 3. Remote Control (2 AAA batteries not included) (1pcs) 2 Downloaded from www.Manualslib.
Customer Service and Support To Obtain Warranty Support or Advice, Please Complete These Easy Steps: Contact LIFESMART PRODUCTS Technical Support Phone: 1-866-484-2066 or 1-214-614-2509 E-mail: Warranty@lifesmartproducts.com Visit us: www.lifesmartproducts.com You will need to provide the unit's model number, serial number (located on the heater’s front panel, rear panel, or on the box), date of purchase, retailer of purchase, a daytime phone number, and possibly a copy of your receipt.
INTRODUCTION Thank you for choosing one of the best Infrared distribution heaters available on the market today. Our Infrared Heater is a very safe and effective room heater. It produces safe, clean and economical heat by utilizing quartz infrared heating elements. The heating process of the Infrared Heater is similar to the way the sun warms the earth. The infrared elements warm the heat chamber and the whisper quiet fan distributes the accumulated warmth.
IMPORTANT SAFETY INSTRUCTIONS READ AND UNDERSTAND ALL INSTRUCTIONS, SAFETY WARNINGS, AND FAQ’s BEFORE USING THE HEATER WARNING! ! POTENTIAL FOR ELECTRICAL HAZARD IF NOT ADHERED TO! When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following: 1. This heater must be plugged into a 120V, 15 amp (or more) circuit of its own. Nothing else can be plugged into the same circuit.
10. Never place heater where it may fall into a bathtub or other water receptacles. 11. Do not run cord under carpet. Do not cover cord with throw rugs, runners, or similar coverings. Arrange cord away from traffic area and where it will not be tripped over. 12. The heater must be plugged into a wall outlet that is a DEDICATED CIRCUIT, with a minimum 15 amp rating on that individual circuit. 13.
FREQUENTLY ASKED QUESTIONS (FAQ’S) My heater emits a “strange” odor when I first open the box/when I turn the heater on for the first time. Why is this happening? This is normal. This heater is treated with a special heat safe/resistant coating. This odor will sometimes be present when the box is opened, and may be compared to a heaters version of “new car smell.” Also, similar to all hearth appliances (woodstoves, etc.
Once I plug the unit in and turn it on, how long will it take to heat my room? The heating process in the heater begins immediately upon powering on, and setting the desired temperature above the ambient temperature. A noticeable change in the l room’s ambient temperature will vary.
plugged into that circuit or outlet). If unsure your circuit meets these requirements, verify with a certified electrician. Risk of fire, damage to property, or injury may result if requirements are not met. Why does my heater’s fan continue to run after the set temperature is reached or the power is turned off? This is normal. The heater’s fan will continue to run, even after the heater automatically cycles down.
central heat the boost it needs. If you intend on using it as a single heat source, especially in larger homes (which you may), expect the heater to 1) take as much as 24 hours to heat the area, 2) stay on for longer periods of time (without cycling off) due to heat loss, and 3) increased use time, and electric costs. My heater’s display shows my ambient temperature to be in the 20’s, when I know it is warmer than that. Why? The heater’s display is defaulted to read the temperature as Fahrenheit.
HEATER OPERATION Here is a small description of how our heaters work: Operation Mechanism: 1) Air is brought into the heater through an easy to clean, washable filter at the rear of the unit. 2) The highly efficient, one-speed, high volume fan pushes filtered air through the chamber, across the heat elements. 3) During this exchange, heat is accumulated and transferred to the air in the chamber.
HEATER PLACEMENT By using this infrared heater you can efficiently heat up to 1500 of unobstructed square feet. This heater is NOT intended to replace your home’s furnace. Rather, it is designed to be a supplement to it. It is not an instant heater, and on occasions (depending on various factors), can take up to 24 hours for a room to reach the desired temperature.
USER’S GUIDE Plug your Infrared Heater power cord into a 120V, 15amp (or higher) three-prong receptacle. To Turn the Heater On: 1. Turn the Master toggle switch in the back of the heater to the “On/Lit” position. 2. Press the “Power” button on the front control panel or “ON/OFF” button on the remote control. Heater Default Temperature: The heater’s default temperature every time it is powered “on” is 72°F.
To Set Heat Mode: Press the “High/Low/Eco” button on the control panel or “H/L/E” on the remote control to switch between the High, Low, and Eco modes. The corresponding High, Low or Eco light will switch on. Note that in all modes, the fan speed will remain the same. Heating Process: In the High Mode, all heating elements will engage for full 1500 Watt heating capacity. In the Low mode, corresponding heating elements will engage to heat at 1000 Watts, to save energy.
FILTER MAINTENANCE Your Infrared Heater is equipped with an easy to clean, washable static filter. Regular cleaning and maintenance of your filter will ensure a lifetime of trouble-free use. 1. Turn off the heater. Locate the filter at the rear of the heater and lift out (some filters may be held on by brackets. Others may be magnetic. Others may require loosening up some screws). 2. Rinse the filter by spraying warm tap water through the filter.
Limited Manufacturer Warranty 1 Year Limited Warranty: LIFESMART warrants this heater against defects in materials and workmanship on functional parts, for a period of one year from the original date of purchase. Your sales receipt showing the date of purchase of the product is your proof of purchase. Keep it in a safe place for future reference.
Warranty Limitations This warranty does not apply if the unit has been subject to negligence, fabrication, misuse, abuse, or repairs (unless authorized verbally, or in writing, by an Authorized LIFESMART Representative) alteration by non LIFESMART authorized personnel, inappropriate installations, or any case beyond the control of LIFESMART .
Legal Remedies This limited warranty gives the original purchaser specific legal rights. Other rights may vary from state to state. LS-6BPIQH-X REV1 Printed in China 18 Downloaded from www.Manualslib.
