LS100DX - LS600DX OWNER’S MANUAL 115V / 230V Models
LIFESMART OWNER'S MANUAL Owner's Record Locating the Spa Serial Number: The spa serial number label is located on control box cover inside the equipment compartment. Equipment compartment access panel is below the spas 4-button topside control panel. You will need the spa model and serial number to properly register your spa and activate coverage. Write your spa information in the space provided.
TABLE OF CONTENTS Title Page SAFETY INFORMATION IMPORTANT SAFETY INSTRUcTIONS.....................................................................................................................................1 Important spa instructions.............................................................................................................................................4 INSTALLATION pLANNING A LOCATION FOR YOUR SPA.........................................................................
SAFETY INFORMATION IMPORTANT SAFETY INSTRUcTIONS Read and follow all instructions Avoiding The risk to children Danger: • RISK OF CHILD DROWNING. Extreme caution must be exercised to prevent unauthorized access by children. To avoid accidents, ensure that children cannot use a spa unless they are supervised at all times. Warning: • To reduce the risk of injury, do not permit children to use this product unless they are closely supervised at all times.
SAFETY INFORMATION 115 volt Cord-Connected 15 amp models: • The GFCI is located at the end of the power cord. Before each use, with the unit operating, push the TEST button. The unit should stop operating and the GFCI power indicator will go out. Wait 30 seconds and then reset the GFCI by pushing the RESET button. The GFCI power indicator will turn on, restoring power to the spa.
SAFETY INFORMATION • Place electrical appliances within 5 feet (1.5m) of the spa. • Use an extension cord to connect the spa to its power source. The cord may not be properly grounded and the connection is a shock hazard. An extension cord may cause a voltage drop, which will cause overheating of the jet pump motor and motor damage. • Attempt to open the electrical control box. There are no user serviceable parts inside. Risks to avoid DANGER: RISK OF INJURY • DO NOT sit in the filter compartment area.
SAFETY INFORMATION Avoiding the risk of hyperthermia Prolonged immersion in hot water can result in HYPERTHERMIA, a dangerous condition which occurs when the internal temperature of the body reaches a level above normal (98.6°F, 37ºC). The symptoms of hyperthermia include unawareness of impending hazard, failure to perceive heat, failure to recognize the need to exit the spa, physical inability to exit the spa, fetal damage in pregnant women, and unconsciousness resulting in a danger of drowning.
INSTALLATION pLANNING A LOCATION FOR YOUR SPA Consider these things when determining where to place your spa. SAFETY FIRST: Make sure your spa is positioned so access to the equipment compartment and side panels will not be blocked. Be certain your installation will meet all city and local safety codes and requirements. PLANNED USE OF Spa: How you intend to use your spa will help you determine where you should position the spa.
INSTALLATION BE AWARE: Damage caused by inadequate or improper foundation support is not covered by the spa warranty. It is the sole responsibility of the spa owner to provide a proper foundation for the spa. Make sure the foundation where the spa is placed drains water away from the spa. Proper drainage will keep components dry from rain and wet weather. Your spa weight must always be considered when installing your spa.
Equipment access Equipment Access Panel Topside Control Panel Slat Slat Screw Equipment Access Panel Door Hose Bib GFCI Cord Electrical Recess Drain Hose Black ABS Door To access the equipment compartment: • Remove 1 vertical slat and 3 screws on each side of Equipment Access Panel Door. • Remove 6 screws from Equipment Access Panel Door to remove door. • Remove screws from Black ABS Door (if your spa has vertical slats) to access Equipment Compartment.
ELECTRICAL REQUIREMENTS Electrical DO NOT PLUG IN YOUR SPA WITHOUT FIRST FILLING WITH WATER! DANGER – RISK OF ELECTRIC SHOCK Installations that do not conform to the following procedures and requirements may expose users to electric shock. Non-conforming installations will not be covered under warranty. Your electrical outlet must have been installed by an electrical contractor and been approved by a local building electrical inspection authority. 115V ElecTRICAL 1.
ELECTRICAL REQUIREMENTS 8. CAUTION, 230V POWERED SPAS – These spas must be hard wired to your household electrical service box only. Do not use an extension cord or any other disconnect-able power cord. The use of an extension cord or a disconnect-able power cord is highly dangerous and will void all warranties! • • • • Wire size must be appropriate per NEC and/or local codes. Wire size is determined by length of run from breaker box to spa and maximum current draw. THHN copper core wire is recommended.
ELECTRICAL REQUIREMENTS CIRCUIT BREAKER REQUIREMENTS: A new GFCI circuit breaker must be used for your spa installation. Do not use an existing breaker, as its condition is unknown. BREAKER Capacity # of wires 230V 32 amps 4 On 230V systems always use a 4 wire system. ON all systems, the spa must be connected to a dedicated GFCI circuit breaker that is not shared with any other equipment. Do not use extension or plug type cords of any kind.
ELECTRICAL REQUIREMENTS electrical wiring diagram for 230V use It is recommended that a licensed electrician install the power to your spa in accordance with the National Electric Code and/or any local electrical codes in effect at the time of installation. Power supply installation must include a properly rated GFCI circuit breaker. The circuit must be dedicated and should not be shared with any other appliances. The power supply must be hard wired into the power pack.
control panel operation Initial start-up - Your spa has been designed so that by simply connecting power to the spa, the spa will automatically heat the water to the factory set temperature of 100°F unless you set the spa to a different temperature. If power is disconnected from the spa, it will automatically revert back to the factory set Temperature of 100°F when power is reapplied. Temperature Adjustment (80°F-104°F) The current temperature is constantly displayed on the LED.
control panel operation Standard Mode: Is programmed to maintain the desired temperature. Note: the last measured spa temperature displayed is current only when the pump has been running for at least 2 minutes. “St” will be display momentarily only when dip switch 7 is OFF. Economy Mode: Heats the spa to the set temperature only during filter cycles.
control panel operation Display Messages (LS100DX - LS450DX) Should you see two letters on your control panel display do not enter your spa until you find the two letter message below and complete the steps to remove the display message from the control panel. OH “Overheat” (Spa is deactivated) DO NOT ENTER THE WATER. If the spa water has reached 107°F, remove the spa cover to cool the water. At 106°F, the spa should reset itself. If the high-limit sensor detects 118°F, the spa will shut down.
control panel operation Message Meaning SA Spa is shut down – The sensor that is plugged into the Sensor “A” jack is not working. Sb Sn HL LF Dr dY Action Required Turn spa off for 30 seconds then back on. If the problem persists, contact Customer Service. It may appear temporarily in an overheat situation and disappear at cool. Spa is shut down. The sensor that Turn spa off for 30 seconds then back on. If the is plugged into the Sensor “B” jack is problem persists, contact Customer Service.
component operation Spa component operation AIR CONTROL VALVE The air control valve serves to regulate the amount of air mixed with the water when the jets are operational. Rotate the air control in one direction to achieve the maximum jet pressure and therapeutic action. Rotating the air control in the opposite direction to turn air off and allow the jets to work with water only.
Fill Up and Start-up instructions The following procedures should be followed on initial startup and whenever the spa is drained for routine maintenance. FILLING THE Spa WITH WATER 1. Clear all the debris from your spa. 2. Be sure to open all Jets to allow as much air as possible to escape from the plumbing during the filling process. 3. Use a garden hose to fill your spa with water. NOTE: Do not use hot or softened water. 4.
adding start-up chemicals WATER CHEMISTRY GUIDELINES The following step-by-step instructions are a recommended guideline for balancing water chemistry. If unsure about any step in the process, please contact a Customer Care Associate at (888) 961-7727) or by email at ahsservice@watkinsmfg.com. Initially, it is advisable to identify what minerals (e.g. iron) are present in the local source water. This will provide a better understanding of how to treat the water.
spa maintenance FILTER CARTRIDGE MAINTENANCE Every two weeks, the filter cartridge should be cleaned to remove the objects and particles that have lodged in the cartridge pleats. Using household water pressure and a garden hose with a pressurized nozzle, push water from inside to outside of the pleats, forcing all the trapped particles out. NOTE: Never run your spa without a filter cartridge!!! This will invalidate your warranty.
SPA MAINTENANCE SURFACE CARE Do not use solvents or abrasive cleaners to clean the spa. Typically, a mild detergent and water will resolve cleaning issues. COVER CARE Please keep your cover free from dirt at all times. Use a cover cleaner or a warm mild soapy water to clean the surface. Do not use any silicone-based products, as it will dry and may eventually crack the vinyl. NOTE: Do not stand on the cover at any time. Remove the cover when adding chemicals to your spa.
Draining or winterizing Every three to six months, depending upon the water condition, you need to renew your water. CAUTION: READ THIS BEFORE DRAINING YOUR SPA • To prevent damage to the spa’s components, unplug the spa from the outlet before draining. Do not plug your spa back in until your spa has been refilled with water. • There are certain precautions to keep in mind when draining your spa. If it is extremely cold, and the spa is outdoors, freezing could occur in the plumbing or the equipment.
troubleshooting procedures In the event your spa is not working the way it should, please first review all the installation and operating instructions in this manual and check the message on the panel display. If you are still not satisfied it is working properly, please follow the appropriate troubleshooting instructions. CAUTION! WARNING! SHOCK HAZARD! No User Serviceable Parts. Do not attempt service of the control box. Contact customer service for assistance.
replacement parts Replacement spa parts PART NUMBER DESCRIPTION 303279 SPA FILTER – 50sq. ft. Filter 303263 SPA FILTER – 25sq. ft.
24
Part # 303468 Rev.
