User's Manual

interference to radio or television reception, which can
be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by
one or more of the following measures:
o Reorient or relocate the receiving antenna
o Reorient or relocate and increase the
separation between the equipment and
receiver
o Connect the equipment into an outlet on a
circuit different from that to which the receiver
is connected.
Some cordless telephones operate at frequencies that
may cause interference to nearby TVs or VCRs. To
minimize or prevent such interference, the base or the
cordless telephone should not be placed near or on top
of a TV or VCR. If interference is experienced, move
the cordless telephone further away from the TV or
VCR. This will often reduce, or eliminate, interference.
Consult an experienced radio/TV technician for help if
these measures do not eliminate the interference.
The antenna used with this product must be installed to
provide a separation distance of at least 20 cm from all
persons and must not be co-located or operating in
conjunction with any other antenna or transmitter.
This equipment should be serviced only by Ingrid, Inc.
or its authorized agents.
FCC Part 68
This equipment complies with Part 68 of the FCC rules
and the requirements adopted by the ACTA. On the
equipment there is a label that contains, among other
information, a product identifier in the format
US:AAAEQ##TXXXX. If requested, this number must
be provided to the telephone company.
A plug and jack used to connect this equipment to the
premises wiring and telephone network must comply
with the applicable FCC Part 68 rules and requirements
adopted by the ACTA. A compliant telephone cord and
modular plug is provided with this product. It is
designed to be connected to a compatible modular jack
that is also compliant.
Registration No.: Found on the bottom of the unit.
The REN is used to determine the number of devices
that may be connected to a telephone line. Excessive
RENs on a telephone line may result in the devices not
ringing in response to an incoming call. In most but not
all areas, the sum of RENs should not exceed five (5.0).
To be certain of the number of devices that may be
connected to a line, as determined by the total RENs,
contact the local telephone company. For products
approved after July 23, 2001, the REN for this product
is part of the product identifier that has the format
US:AAAEQ##TXXXX. The digits represented by ## are
the REN without a decimal point (e.g., 03 is a REN of
0.3).
If this equipment causes harm to the telephone
network, the telephone company will notify you in
advance that a temporary discontinuance of service
may be required. But if advance notice isn’t practical,
the telephone company will notify you as soon as
possible. Also, you will be advised of your right to file a
complaint with the FCC if you believe it is necessary.
The telephone company may make changes in its
facilities, equipment, operations or procedures that
could affect the operation of the equipment. If this
happens, the telephone company will provide advance
notice in order for you to make necessary modifications
to maintain uninterrupted service.
If trouble is experienced with this equipment, for repair
or warranty information, please contact InGrid, Inc. at
877-INGRID7
or [e-mail]. If the
equipment is causing harm to the telephone network,
the telephone company may request that you
disconnect the equipment until the problem is resolved.
Connection to a party line service is subject to state
tariffs. Contact the state public utility commission,
public service commission or corporation commission
for information.
You must not connect your phone to:
o Coin operated systems
o Most electronic key telephone systems
If you home has specially wired alarm equipment
connected to the telephone line, ensure the installation
of this equipment does not disable your alarm
equipment. If you have questions about what will
disable the equipment, consult your telephone company
or a qualified installer.
Caution – To ensure proper operation, this equipment
must be installed according to the enclosed installation
instructions. To verify that the equipment is operating
properly and can successfully report an alarm, this
equipment must be tested immediately after installation,
and periodically thereafter, according to the enclosed
test instructions.
Caution – This equipment cannot report an alarm when
other equipment (telephone, answering system,
computer modem, etc.) connected to the same line is in
use.
Functionally equivalent equipment or wiring used to
provide
Line Seizure capability without the use of an RJ31X or
RJ38X jack may be used. See Line Seizure
instructions.
Caution – Verification of line Seize capability should be
made immediately after installation, and periodically
thereafter, in order to ensure that this equipment can
initiate a call even when other equipment (telephone,
answering system, computer modem, etc.) connected
to the same line is in use.
Industry Canada (I.C.) Notice
Terminal Equipment
Notice: This equipment meets the applicable Industry
Canada Terminal Equipment Technical Specifications.
This is confirmed by the registration number. The
abbreviation, IC, before the registration number
signifies that registration was performed based on a
Declaration of Conformity indicating that Industry
Canada technical specifications were met. It does not
imply that Industry Canada approved this equipment.