User's Manual

For this step you will need your Console and Sensor:
Remove battery tab
Using Console:
Press MENU
Scroll to Security Setup, press SELECT
(Scroll Button found on right side of Console)
Enter default Master Code 1234
Scroll to Sensors, press SELECT
On <Add New>, press SELECT
Scroll to the type of Sensor (Open/Close) and press SELECT
Wait 5 seconds before clipping the Sensor into the Bracket. You will then have
30 seconds to complete the installation. The display shows the time remaining
Clip the Sensor into the Bracket. The Console will beep when
the system finds the Sensor. This may take a few seconds*
Press OK
Edit Sensor Name (Optional)
You may change the name now or at a later time.
• To change the Sensor Name, press the DELETE key to remove the default name
• Using the keys on your Console keypad, type in the desired name
• Press OK when complete
Sensor Placement: Scroll to Door or Window. Press OK
Alarm Type: Scroll to Stay & Away, Away Only, or Convenience. Press OK
Sensor Extension: Scroll to Sensor Only. Press OK
Testing your Sensor:
Test your Sensor by opening the door. Correct installation will generate a chime.
Otherwise, see troubleshooting in User Manual
Repeat Step G for additional Sensors
Place & Program Sensor
IMPORTANT: IF YOU HAVE CLIPPED THE SENSOR INTO THE BRACKET
PLEASE SEE “RESET INSTRUCTIONS” BELOW.
Activate Your System
4
A
B
C
H
D
E
F
G
J
K
I
A
Battery Tab
B
C
D
E
F
G
H
I
J
K
L
M
N
NOTE: IF YOU DO NOT SUBSCRIBE TO PHONE SERVICE, GO TO LIFESHIELD.COM
AND CLICK SETTINGS, THEN CLICK “EDIT” ON THE SYSTEM SETTINGS WINDOW.
CLICK “NO” NEXT TO “HOME PHONE LINE” FIELD, THEN CLICK “CONTINUE” AT
THE BOTTOM OF THE WINDOW.
NOTE: LOW BATTERIES MAY CAUSE A TROUBLE BEEP. TO CANCEL TROUBLE
BEEP AND ALLOW TIME FOR CHARGING, PRESS CANCEL/OFF KEY, THEN
PRESS OK ON DISPLAY.
C
Your system is now operational. If you subscribe to Alarm Monitoring Service, for the next
seven days it will be in a non-monitored “Practice” mode to allow you to become fully
acquainted with all of its features. For help, call Customer Support at 1-888-392-2044.
* NOTE: IF YOU DO NOT SUBSCRIBE TO ALARM
MONITORING SERVICE, STEPS J AND K DO NOT APPLY.
7
O
P
8
3b
A
Scroll
Buttons
Menu
B
C
Scroll
Buttons
Menu
D
*NOTE: IF THE SYSTEM DID NOT FIND THE SENSOR, REFER TO SENSOR
RESET INSTRUCTIONS, THEN REPEAT STEPS ABOVE.
Using PC:
Go to www.LifeShield.com
Enter User Name and Password
Click on “Get Activation Code” and a 6-digit code
will be provided
Using Console:
Press MENU
On Activate, press SELECT
Enter Activation Code and press SEND
Upon activation acceptance press OK
Enter Master Code (Select a new 4-digit
code used to access and control the system)
Re-enter Master Code to confirm
Now testing communication to Alarm Monitoring Center*
Upon completion press OK*
PHNBK MENU CONNCT WEATHR ALERTS
Ready To Arm
Thu 2/8 11:48a
Calls: 0 Msg:0
PHNBK MENU CONNCT WEATHR ALERTS
Ready To Arm
Thu 2/8 11:48a
Calls: 0 Msg:0
Emergency Contact Profile
Name: Joe Safety
Phone: [phone]
Email: [e-mail]
Second Emergency Contact Profile
Name: Mary Safety
Phone: [phone]
Monitoring Site Profile
Address 1: 770 Township Line Road
Address 2: Suite 350
City: Yardley
State: PA
Zip: 19067
County: Bucks
Township/Borough: Yardley
Monitoring Site Profile
edit
help