User's Manual

Users. They do not have to be returned to
factory default settings.
Follow these steps to assign Users to Key
Chain Remotes:
1. Press Menu and Select
Setup/Security/Key Chains/<Add New>
2. You will be asked to wait 5 seconds
and then will be instructed to press all 4
keys on your keychain.
3. You will be informed that the Keychain
has been found and added and asked to
confirm. Press OK to add.
4. You will then be asked to assign the
keychain to a user. The system provides
a list of the Users on your system.
Select the User to which the Keychain is
being assigned.
5. You will then be asked to enable or
disable the PANIC function on the key
chain remote. The default setting is with
PANIC enabled.
6. By pressing STAY and AWAY
simultaneously, the PANIC alarm will be
tripped.
Reactivate the System
After the hardware is re-installed, go to the
My Ingrid website to reactivate your system.
When you returned your original Base, you
received a new User Name and six digit
Activation Code by e-mail. Use the new
User Password and Activation Code you
received to enter the My Ingrid website.
You should go directly to the Activation
prompt. Click on Activation and follow the
instructions for activating your system.
If you have any trouble with Activation,
contact InGrid Customer Service at
FCC Information
FCC Part 15
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2)
this device must accept any interference received,
including interference that may cause undesired
operation.
CAUTION:
Changes and modifications to this product not
expressly approved by InGrid, Inc. could void not only
the user’s authority to operate this device, but also the
limited warranty.
Note:
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to
radio communications. However, three is no guarantee
that interference will not occur in a particular
installation. If this equipment does cause harmful
interference to radio or television reception, which can
be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by
one or more of the following measures:
o Reorient or relocate the receiving antenna
o Reorient or relocate and increase the
separation between the equipment and
receiver
o Connect the equipment into an outlet on a
circuit different from that to which the receiver
is connected.
Some cordless telephones operate at frequencies that
may cause interference to nearby TVs or VCRs. To
minimize or prevent such interference, the base or the
cordless telephone should not be placed near or on top
of a TV or VCR. If interference is experienced, move
the cordless telephone further away from the TV or
VCR. This will often reduce, or eliminate, interference.
Consult an experienced radio/TV technician for help if
these measures do not eliminate the interference.
The antenna used with this product must be installed to
provide a separation distance of at least 20 cm from all
persons and must not be co-located or operating in
conjunction with any other antenna or transmitter.
This equipment should be serviced only by Ingrid, Inc.
or its authorized agents.
FCC Part 68
This equipment complies with Part 68 of the FCC rules
and the requirements adopted by the ACTA. On the
equipment there is a label that contains, among other
information, a product identifier in the format
US:AAAEQ##TXXXX. If requested, this number must
be provided to the telephone company.
A plug and jack used to connect this equipment to the
premises wiring and telephone network must comply
with the applicable FCC Part 68 rules and requirements
adopted by the ACTA. A compliant telephone cord and
modular plug is provided with this product. It is
designed to be connected to a compatible modular jack
that is also compliant.
Registration No.: Found on the bottom of the unit.