Installation Guide

Installation Instructions
lifeproof™ Waterproof Rigid Core
Luxury Vinyl Multi-Width Plank Flooring
For Assistance, Call: 1-866-843-8453
www.homedepot.com
Product Description
6.5 mm thick x 4.25 in., 5.59 in., 9.84 in.
(three plank widths) x 47.64 in. long
Rigid Core Vinyl Planks
Grade Levels
Above Grade / On Grade
Below Grade
Installation
Method
Floating - Drop
and Lock
3 HOMEDEPOT.COM/LIFEPROOF
Revised 1/16/2017 Please contact 1-866-843-8453 for further assistance.
Helpful Pointers
GENERAL TIPS
□ Make sure your work area is well lit. Good visibility ensures that color is consistent and that visually defective planks are detected and removed.
□ The minimum length of the first and last plank is 8 in.. If the last plank will be less than 8 in., adjust the length of the first plank. The remainder of the last
plank can be used as a starter board on the following rows.
□ Using a shorter piece at undercut door jams will help when fitting flooring in place.
□ Never hit the flooring directly with the tapping block and be careful not to fracture floor edges.
CUTTING THE LAST ROW TO WIDTH
□ Most often the entire length of the last row will need to be cut so that it is narrow enough to fit the remaining space.
□ Measure the distance between the floor face edge (exclude the tongue) to the wall. Subtract 1/4 in. from this measurement for expansion gap. Draw a line.
Cut through the line. Discard the excess piece. Proceed with the installation.
Preparing for Installation
□ Ensure subfloors are clean.
□ Lay out several cartons. Randomly rack planks to ensure good color and shade
mixture and end joint spacing. Minimum end stagger is 8 in. Inspect plank quality and
grading.
□ Lay out trim moldings in advance and find planks whose shade closely matches. Set
these aside for future use.
□ Remove the existing base, shoe molding or threshold carefully. They can be used to
cover the 1/4 in. expansion gap left around the edge of the room.
□ Undercut doors and casings using a handsaw laid flat on a piece of scrap flooring.
Never undercut metal door casings.
1. INSTALLING THE FIRST ROW
a. First, lay a row of loose planks (i.e. without securing them to each other; Figure 1.1) to
determine if you need to adjust the length of the first plank to avoid a small piece (less
than 8 in.) on the opposite wall from where you started. Alternatively, measure the
length of the room and divide by the length of one plank. If the remainder is less than 8
in., calculate ½ of the remainder and trim this amount off the first plank. The last plank
should be the same length as the first one. To cut a plank, simply measure and mark
the plank. Then, use a straight edge and utility knife to score and snap.
b. Installation should start in a corner (left hand) and proceed from the wall with the
tongue facing the wall (Figure 1.2). Allow a minimum gap of 1/4 in. (6 mm) for subfloor
movement or product expansion, which should be covered by molding. Set 1/4 in.
spacers to create the required expansion space.
c. lifeproof
TM
Multi-Width Plank has three different width planks (Figure 1.3) that can
be installed in several different patterns. The pattern you choose will alter how you
install the first two rows. One option is shown here (Figure 1.4, Pattern 1). Alternative
possibilities are shown above in the “Preparing for Installation” section.
d. For Pattern 1, your first row will start with a 4.25 in. (small) plank and a 5.59 in.
(medium) plank paired together. It does not matter if the smaller plank is used first
against the wall you are starting from, or if you use the medium plank first. Connect
the long sides of the two planks together, making sure the end joints line up evenly.
Then interlock a 9.84 in. (large) plank at the end joints of the first two planks by
inserting the tongue into the groove of the adjoining planks. Next, you will pair another
small plank and medium plank together, adjoining it to the end of the 9.84 in. plank you
just laid. Continue this method to finish the first row.
Installation
Pattern 1 Pattern 2 Pattern 3
1.1
1/4 in. / 6mm
tongue
groove
1.2
5.59"
9.84"
4.25"
1.3 1.4
Pattern 1