LIERDA SCIENCE & TECHNOLOGY CO., LTD. Product Specification Product Name：P-series BLE Module Document version：V1.
Contents Chapter 1 Feature ............................................................................................................................................1 Chapter 2 Parameters ......................................................................................................................................2 Chapter 3 Product Specification .....................................................................................................................3 3.1 boundary dimension ............
Chapter 1 Feature Lierda P-Series Low Power Consumption High performance Bluetooth transceiver Module is designed based on TI CC2541 chip. The Module has ceramic integrate antenna, and adopts SMT attachment interface. It has a complete open port which reduces hardware design difficulties and also provide high structural and software flexibility for users. The module has low power consumption, a compact size and have high resistance to disturbance.
Chapter 2 Parameters Sheet 2-1 Module Parameters Item Supply voltage frequency Power consumption Emission power Operating ambient temperature range Storage temperature range channel modulation format Communication I/O Control Remarks Parameters 2.0 ~ 3.6 V（classic 3.3V） Low power may cause failure.
Chapter 3 Product Specification 3.1 outline dimensional drawing Figure 3-1 Module dimension and interface *Size tolerance which not be marked according to GB/T1804-m standards 3.2 Pin Definition Sheet 3-1 Pin Definition Number Name 1 ANT 2 VCC Power IN 3 GND Ground 4 P0.0-P0.7 I/O port 5 P1.0-P1.
Number Name 功能 6 P2.1-P2.2 I/O port 7 SCL_UP I2C port SCL 8 SDA_UN I2C port SDA 10 REST_N Reset Active Low 备注 More detail for the IO type and load capacity could be found in “CC2540/41 System-on-Chip Solution for 2.4-GHz Bluetooth® low energy Applications”, this module lead them directly. P – Series Module did not set Reset-cicuit for the REST_N pin. please refer to the chapter 4 when you design. 3.
Chapter 4 Typical Circuit VCC GND GND GND 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 * ANT GND RESET_N P2.2 P0.0 P2.1 P0.1 GND P0.2 P1.7 GND P1.6 P0.3 SCL_UP SDA_UN P0.4 GND P0.5 P0.6 VUSB_NC P0.7 P1.5 P1.0 P1.4 VCC P1.3 GND P1.2 P1.1 P系列BLE模块 47K 29 28 27 26 25 24 23 22 21 20 19 18 17 16 2.7K 1nF GND VCC GND Figure 4-1 Typical application circuit This is min-application circuit ,other circuit could be found in “ application user guide”.
Chapter 5 Pakge 1,Each one module has tape and reel packaging ,and this reel transparent plastic tape attached is 32mm wide, this tape is 25.5mm waide. Figure 5-1 tape and reel packaging Figure 5-2 size of tape and reel 2,Each reel consists of 1600 pieces. Then put it into a antistatic bag make of PET\AL\PP material. Size of the bag are 42cm * 45cm . 3,Next put the bag into a box, size of the box are 36.5cm *36.5cm *6cm.
Figure 5-3 Whole box packaging 4,Every 5 boxes put into a case, size of the case are 37.5cm * 37.5cm * 32cm.there are total 8000 pieces in one case .
Appendix One BLE Profile brief introduction Bluetooth 4.0 Applications are classified into two types-The classic BR/EDR system and the BLE System. The BLE system was designed aimed to lower the power consumption and to extend the battery life of the Bluetooth system. Those module that support both BR/EDR and BLE are called the "Dual Mode Bluetooth", whereas those that only support BLE are called the "Single Mode Bluetooth" . The L-series Bluetooth module are the Single Mode modules.
Name Function OPP Object Push Profile PAN Personal Area Networking Profile PBAP Phone Book Access Profile SAP SIM Access Profile SDAP Service Discovery Application Profile SPP Serial Port Profile SYNCH Synchronization Profile VDP Video Distribution Profile Remark Bluetooth to Uart For the BLE ,there are new profile and specification, like sheet F-2.
Name Function HTS Health Thermometer Service HRP Heart Rate Profile HRS Heart Rate Service IAS Immediate Alert Service LLS Link Loss Service NDCS Next DST Change Service PASP Phone Alert Status Profile PASS Phone Alert Status Service PXP Proximity Profile RSCP Running Speed and Cadence Profile RSCS Running Speed and Cadence Service RTUS Reference Time Update Service ScPP Scan Parameters Profile ScPS Scan Parameters Service TIP Time Profile TPS Tx Power Service Remark We co
Notes to users 1. Thanks for choosing Lierda products. Please read through this Manual before using the products. By using the products, you have understood and accept the terms and instructions in this Manual. 2. This equipment can be used in member states of the European Union once the corresponding administrative license is obtained. Lierda Science & Technology Co.
