User Manual

4.3.3 Changing the bearing parts
Fig. 7
u
Using the accompanying Allen key, unscrew the threaded
pin
Fig. 7 (40) by about 1 turn.
u
Turn and lift out the bearing pin Fig. 7 (22) together with
washer Fig. 7 (23) and adjustable-height foot Fig. 7 (24) .
u
Lift off the stopper Fig. 7 (21) .
u
Unscrew the turn hinge Fig. 7 (25) .
u
Fully unscrew the threaded pin Fig. 7 (40) and screw it in on
the opposite side, at the turn hinge, until it is flush outside
with the turn hinge.
u
Unscrew the bearing element Fig. 7 (28) , turn it through
180° and screw it firmly back into place .
u
Re-insert the stopper Fig. 7 (21) into the other hole.
u
Carefully lift off the cover on the handle side Fig. 7 (27) and
transfer it to the opposite side.
u
Screw the turn hinge Fig. 7 (25) firmly into place on the new
hinge side, possibly using a cordless screwdriver (with
4 Nm).
u
Re-insert the bearing pin Fig. 7 (22) together with washer
and adjustable-height foot.
u
Tighten the threaded pin Fig. 7 (40) .
4.3.4 Transferring the handle
Fig. 8
u
Lift the stopper Fig. 8 (30) out of the door bearing bush and
transfer it.
u
Dismantle the door handle Fig. 8 (31) , stoppers Fig. 8 (32)
and pressure plates* Fig. 8 (33) and transfer to the opposite
side.
u
When fitting the pressure plates on the opposite side, make
sure they snap properly into place.*
4.3.5 Fitting the door
u
Place the door from above onto the lower bearing pin
Fig. 7 (22) .
u
Close the door.
u
Insert the upper turn hinge Fig. 6 (12) in the door on the new
hinge side.
u
Screw the upper turn hinge Fig. 6 (12) firmly into place (with
4 Nm)(2x Torx® 25) Fig. 6 (13) . Possibly make preliminary
holes with a bradawl or use a cordless screwdriver.
u
Snap the cover Fig. 6 (10) and cover Fig. 6 (11) into place at
the opposite side.
4.3.6 Fitting the soft stop unit
Fig. 9
u
Remove the cover
Fig. 9 (7) from the faceplate Fig. 9 (1) and
re-insert it at the other side.
u
Engage the soft stop unit with the joint pointing to the hinge
side (A) and swivel into place (B).
w
The screw holes at the left and right have to register.
u
Screw down the soft stop unit (2x Torx® 15) Fig. 9 (6) .
Fig. 10
u
Attach the faceplate Fig. 10 (1) to the soft stop bracket so
that the catches face forwards and the front faces the appli-
ance.
u
Draw the soft stop bracket Fig. 10 (5) towards the bearing
part Fig. 10 (26) and re-insert the pin Fig. 10 (4) from above
so that the square sits in the recess.
u
Attach and engage the cover Fig. 10 (2) .
w
Pay attention that the cover fits properly so that the door
closes properly and the pin is secured.
u
Twist the safety lock Fig. 10 (3) for removal.
u
Snap the faceplate Fig. 10 (1) onto the door.
u
Close the door.
4.3.7 Aligning the door
u
Align the door to the appliance housing by way of the two
oblong holes in the bottom turn hinge
Fig. 7 (25) . To do so,
unscrew the middle screw.
Putting into operation
* Depending on model and options 7