Design Guide 2009 Built In Models 24" and 48"
7082440-01
Welcome Liebherr's engineering excellence in Germany provides the largest selection of freezers, refrigerators and wine refrigerators worldwide. Liebherr appliances consistently specializes in the manufacturing of high quality freezers and refrigerators. With more than 300 basic models, we have the widest selection in the world. Liebherr appliances feature premium quality, numerous innovative product ideas and advanced design.
Introduction LIEBHERR WARRANTY PLAN FULL TWO YEAR WARRANTY - For two years from the date of original purchase, your Liebherr Warranty covers all parts and labor to repair or replace any part of the product which proves to be defective in materials or workmanship. FULL FIVE YEAR WARRANTY - For five years from the date of original purchase, your Liebherr Warranty covers all parts and labor to repair or replace any components that prove to be defective in materials or workmanship in the sealed system.
Contents General Remarks Safety Warnings I Electrical Requirements & Safety II IceMaker (if equipped) III Area Requirements IV Safety Regulations V Built In Models 24" and 48" 24" and 48" Models Overview Overlay and Framed Panel 1 Overview Stainless steel 6 Unit Dimensions "Solo" Overlay and Framed Panel 7 Unit Dimensions Dimensions "SBS" Overlay and Framed Panel 9 Unit Dimensions Dimensions "Solo" Sta
General Remarks I. Safety Warnings PLEASE READ AND FOLLOW THESE INSTRUCTIONS This design guide contains Warning and Caution statements. This information is important for safe and efficient installation. This design guide is not replacing the use and care manual which contains important information on how to use Liebherr appliances. Always read and follow all Warning and Caution statements! States a hazard that may cause serious injury or death if precautions are not followed.
General Remarks II. Electrical Requirements & Safety III. IceMaker (if equipped) A 115 Volt, 60 Hz, 15 Amp (20 Amp for side-by-side installation) fused electrical supply is required. Connect undercounter wine cabinet to a 115 VAC, 10 amp (15 Amp for side-by-side installations) circuit that is controlled by a circuit breaker or fuse. We recommend using a dedicated circuit for these appliances to prevent electrical overload.
General Remarks IV. Area Requirements V. Safety Regulations Verify the following: • Floors can support refrigerator’s weight plus approximately 1200 pounds (544 kg) of food weight. Not all Liebherr products are designed for 1200 pounds (544 kg) of food. Some units are smaller and total weights may vary. The appliance complies with UL250 and CAN/CSA-C 22,2 No. 63 and is designed to cool, freeze, store food as well as make ice (if equipped). It is designed as a household appliance.
Built In Models 24" and 48" R, RI 1410 & BF, BFI 1061 - SBS 241, 24I1 Liebherr offers a new concept in cooling technology to the American market. The compact 24" appliances can be used as a single unit or together as a Side-by-Side. Available with stainless steel doors or for custom finish panels on the doors. R & RI 1410 Energy Star: Energy consumption p. a.: Energy Supply: Total capacity: Climate Rating: Door hinges: qualified 325 kWh 115V/60Hz/350W 13.
Built In Models 24" and 48" RB, RBI 1410 & WF, WFI 1061- SBS 246, 24I6 RB & RBI 1410 Energy Star: Energy consumption p. a.: Energy Supply: Total capacity: Refrigerator BioFresh Climate Rating: Door hinges: qualified 320 kWh 115V/60Hz/350W 12.8 cu ft (363 L) 8.7 cu ft (246 L) 4.
Built In Models 24" and 48" RB, RBI 1410 & F, FI 1051- SBS 243, 24I3 RB & RBI 1410 Energy Star: Energy consumption p. a.: Energy Supply: Total capacity: Refrigerator BioFresh Climate Rating: Door hinges: qualified 320 kWh 115V/60Hz/350W 12.8 cu ft (363 L) 8.7 cu ft (246 L) 4.
Built In Models 24" and 48" 4
Built In Models 24" and 48" Overview Overlay and Framed Panel: RI/RBI 1410, BFI/WFI 1061, FI 1051 - SBS 24I1/24I3/24I6 The units of the Liebherr built-in range offer versatile options for customization. Decor frames make it possible to put custom panels on the built-in appliances. To match your kitchen’s design, use custom finished panels, overlay or framed.
Built In Models 24" and 48" Overview Stainless steel: R/RB 1410, BF/WF 1061, F 1051 - SBS 241/243/246 The Liebherr refrigerator-freezer with stainless steel doors can be easily integrated into any kitchen layout. The stainless steel gives a more professional style and it is easily cleaned. No panels are required.
Built In Models 24" and 48" Unit Dimensions: Solo Overlay and Framed Panel BFI, WFI 1061 RI, RBI 1410 FI 1051 Top view Side view right Front view with 80" ventilation grille Height of unit can be increased by 5/8" 7
Built In Models 24" and 48" Top view Side view right without ventilation grille 8 Top view
Built In Models 24" and 48" Unit Dimensions: SBS Overlay and Framed Panel SBS 24I1 SBS 24I3 SBS 24I6 Top view Side view right Front view with 80" ventilation grille Overall height can be increased by 5/8" 9
Built In Models 24" and 48" Top view Top view Front view with 84" ventilation grille Side view right without ventilation grille 10
Built In Models 24" and 48" Unit Dimensions: Solo Stainless steel BF, WF 1061 R, RB 1410 F 1051 Top view Front view with 80" ventilation grille Side view right 11
Built In Models 24" and 48" Top view Side view right without ventilation grille 12 Top view
Built In Models 24" and 48" Unit Dimensions: SBS Stainless steel SBS 241 SBS 243 SBS 246 Top view Side view right Front view with 80" ventilation grille 13
Built In Models 24" and 48" Top view Top view Front view with 84" ventilation grille Side view right without ventilation grille 14
Built In Models 24" and 48" Cabinet Opening Dimensions All units are to open at a minimum of 90° to prevent problems removing drawers. With the door opening 90°, you may have to move drawers slightly to clear the door interior. •Use a minimum 2" (51 mm) filler, for corner installations, so the door can be opened to 90°. If you’re using raised panels, consider using a wider filler. •Use the supplied filler strip when units are installed side by side.
Built In Models 24" and 48" Ventilation Requirements „This is a built-in refrigerator-freezer with either custom finished door panels or stainless steel doors. The unit is not intended for freestanding use and has to be installed inside a cabinet. This type of cabinet must be carefully constructed using the proper dimensions and it must provide proper ventilation to ensure proper appliance operation. B - Side view Kitchen Cabinet Airflow 1.
Built In Models 24" and 48" Handle Clearance It is important to provide adequate clearance behind the handle so that the user's hand fits easily. The clearance may not have to be the entire length of the handle, but should be designed for user's comfort. Please note that for framed installations, the factory Liebherr handles must be ordered.
Built In Models 24" and 48" Custom finish RI, RBI 1410, BFI, WFI 1061, FI 1051SBS 24I1, 24I3, 24I6 Framed and Overlay Panels Liebherr offers numerous options for customization, allowing you to best complement the design of your dream kitchen. Decor frames make it possible to put custom panels on the built-in appliances. To match your kitchen's design, use custom finish panels, overlay or framed.
Built In Models 24" and 48" Framed Panel Dimensions If the thickness of the custom panels is less than 1/4" (6.35 mm), they must be backed up with a sheet of shim material to build the total thickness to 1/4" (6.35 mm). If the panel is thicker than 1/4" (6.35 mm), an edge must be routed around the panel to ensure a proper fit.
Built In Models 24" and 48" Single Installation RI 1410, RBI 1410, FI 1051 Top view Top view 20 Front view
Built In Models 24" and 48" Single Installation BFI 1051 Top view Front view Top view 21
Built In Models 24" and 48" Single Installation WFI 1061 Top view view Top Front view Window cut out Top Topview view 22
Built In Models 24" and 48" Overlay Panel Dimensions The overlay design line allows decorative panels to cover the door trim for a more seamless appearance that blends with the design of the room. The most common way to achieve this look is to work with three panels, the decorative overlay panel, a 3/32" (2.54 mm) spacer panel and a 1/4" (6.35 mm) backer panel.Depending on your cabinet manufacturer, this could be one panel routed for different dimensions or, morelikely, three different panels.
Built In Models 24" and 48" Front view Cut out only for WFI 1061 Top view BFI 1061,WFI 1061 24 Width -W H1 - Wine area H2-Freezer section Thickness of panel Overlay panel (1) 23 5/16”(592.1mm) 33 3/4” (857.1mm) 38 1/8 (968.4 mm) 3/4” (19 mm) Spacer panel (2) 21 1/4”(539.8mm) 31 1/2” (800 mm) 36 3/32” (916.6 mm) 3/32” (2.5 mm) Backer panel (3) 22 3/4” (577.9 mm) 33” (838.1mm) 37 19/32” (954.7 mm) 1/4” (6.4 mm) Cut-out for glass window max. 171/2” (444.
Built In Models 24" and 48" Side-by-Side installation FI 1051, RBI 1410 Front view FI 1051 RBI 1410 SBS 24I3 (FI 1051+RBI 1410) 25
Built In Models 24" and 48" Front view Top view FI 1410,RBI 1410 26 Width-W H-Height Thickness of panel Overlay panel (1) 23 5/16” (592.1mm) 72 1/4” (1835.2mm) 3/4” (19 mm) Spacer panel (2) 21 1/4” (539.8mm) 70 1/16” (1779.6mm) 3/32” (2.5 mm) Backer panel (3) 22 3/4” (577.9 mm) 71 9/16” (1817.7mm) 1/4” (6.
Built In Models 24" and 48" Single installation RI 1410, RBI 1410, FI 1051 Front view Top view Height - H Thickness of panel 23 5/16” 72 1/4” 3/4” (19 mm) (592.1 mm) (1835.2 mm) 21 1/4” 70 1/16” 3/32” (2.5 mm) (539.8 mm) (1779.6 mm) 71 9/16” 22 3/4” (1817.7 mm) 1/4” (6.4 mm) (577.9mm) Width - W Overlay panel (1) Spacer panel (2) Backer panel (3) Single installation BFI 1061 Front view Top view Width - W H1 Refrigerator section H2 Freezer section Overlay panel (1) 23 5/16” (592.1 mm) 33 3/4” (857.
Built In Models 24" and 48" Single installation WFI 1061 Front view Top view Cut out only for WFI 1061 BFI 1061,WFI 1061 Width -W Overlay panel (1) 23 5/16”(592.1mm) Spacer panel (2) 21 1/4”(539.8mm) Backer panel (3) 22 3/4” (577.9 mm) Cut-out for glass window max. 17 1/2” (444.5mm) 28 H1 - Wine area H2-Freezer section Thickness of panel 33 3/4” (857.1mm) 38 1/8 (968.4 mm) 3/4” (19 mm) 31 1/2” (800 mm) 36 3/32”(916.6 mm) 3/32” (2.5 mm) 33” (838.1mm) 37 19/32”(954.7 mm) 1/4” (6.
Built In Models 24" and 48" Cut-out for glass window WFI1061 The edges of the panels 1,2,3 are visible at the transition to the glass window 4 . It can be covered with a glass retainer strip A for esthetic reasons.
Built In Models 24" and 48" Accessories for Framed and Overlay Panels Kits may be necessary to complete this unit's installation or to apply it in a different manner than its original intent. If a kit is necessary, contact your Liebherr retailer or distributor.
Built In Models 24" and 48" 9900300 Handles Trim Kit for framed panels. Made of stainless steel Diameter 3/4" (18 mm) Length: 37-7/8" (962.5 mm) 33-3/8" (847.
Built In Models 24" and 48" For Side-by-Side 48" Unit Installation SBS 24I3 9900308 Side-by-Side Kit Standard installation accessory 9900304 9900344 Top Ventilation Grille 80" Top Ventilation Grille 84" Optional installation accessory 2x9900298 Handles Trim Kit for framed panels. Made of stainless steel Diameter: 3/4" (18mm) Length: Diameter: 3/4" (18 mm) Length: 71-3/4" (1822 mm) Optional installation accessory 2x9900728 Handles for Overlay Panels. Made of stainless steel.
Built In Models 24" and 48" Door Swing Clearance, Overlay appliances, Door hinges left 90° Scale 1:1 33
Built In Models 24" and 48" Door Swing Clearance, Overlay appliances, Door hinges right 90° 34 Scale 1:1
Built In Models 24" and 48" Door Swing Clearance, Overlay appliances, Door hinges left 110° Scale 1:1 35
Built In Models 24" and 48" Door Swing Clearance, Overlay appliances, Door hinges right 110° 36 Scale 1:1
Built In Models 24" and 48" Accessories for Stainless steel Kits may be necessary to complete this unit's installation or to apply it in a different manner than its original intent. If a kit is necessary, contact your Liebherr retailer or distributor.
Built In Models 24" and 48" Door Swing Clearance, Stainless steel appliances, Door hinges left 90° 38 Scale 1:1
Built In Models 24" and 48" Door Swing Clearance, Stainless steel appliances, Door hinges right 90° Scale 1:1 39
Built In Models 24" and 48" Door Swing Clearance, Stainless steel appliances, Door hinges left 110° 40 Scale 1:1
Built In Models 24" and 48" Door Swing Clearance, Stainless steel appliances, Door hinges right 110° Scale 1:1 41
Design Guide 2009
