Installation Instructions For Fully Integrated Freezer MF 1851 / MF 2451 / MF 3051 / MF 3651 7085 859-00
Important Please Read and Follow these Instructions These instructions contain Danger, Warning and Caution notes. This information is important for safe and efficient installation and operation. Always read and comply with all Danger, Warning and Caution notes! DANGER! Danger indicates a hazard which will cause serious injury or death if precautions are not followed. WARNING! Warning indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
Safety Disposal of Old Appliance DANGER! Risk of child entrapment. Child entrapment and suffocation are not problems of the past. Junked or abandoned refrigerators are still dangerous – even if they will sit for “just a few days.” If you are getting rid of your old refrigerator, please follow these instructions to help prevent accidents. Before you discard old appliances: • Take off the doors. • Leave the shelves in place so that children may not easily climb inside.
Planning Information Appliance Dimensions MF 1851 MF 3051 MF 2451 MF 3651 Stated minimum height dimensions include when the levelled feet are fully inserted. Width will increase by 1/4" (6.5 mm) when mounting strips are installed.
Planning Information Door Swing Clearance MF 1851 (top view) MF 2451 Inset installation style A = 8 1/4" (210 mm) B = 1/2" (12.5 mm) C = 19 7/8" (505 mm) Inset installation style A = 10 3/4" (273 mm) B = 1/2" (12.5 mm) C = 25 7/8" (658 mm) Frameless installation style A = 8 1/2" (216 mm) B = 1/2" (12.5 mm) C = 20 3/8" (517 mm) Frameless installation style A = 11" (279 mm) B = 1/2" (12.5 mm) C = 26 3/8" (670 mm) MF 3051 MF 3651 Inset installation style A = 13 1/4" (337 mm) B = 1/2" (12.
Planning Information Cabinet Opening Dimensions Continous toe kick Individual toe kick A Cabinet depth frameless installation style = 25" (635 mm) Cabinet depth inset installation style = 25" (635 mm) plus panel thickness B This is the point where the power cord exits from the appliance rear. 3/4" (19 mm) from the left and 5" (127 mm) from the floor. Free length of the power cord is 98" (2.5 m).
Planning Information Continous toe kick Individual toe kick A Cabinet depth frameless installation style = 25" (635 mm) Cabinet depth inset installation style = 25" (635 mm) plus panel thickness B This is the point where the power cord exits from the appliance rear. 3/4" (19 mm) from the left and 5" (127 mm) from the floor. Free length of the power cord is 98" (2.5 m). IMPORTANT The power plug must be easily accessible so that the appliance can be disconnected from the mains quickly in an emergency.
Planning Information Panel Dimensions 18" recess Inset installation style H = 79 7/8" (2029 mm) W = 17 3/4" (451 mm) Frameless installation style H = 80" (2032 mm) plus overlapping of the panel on the top W = 18" (457 mm) plus overlapping of the panel on both sides Minimum panel thickness = 5/8" (16 mm) * Maximum panel thickness = 1" (25 mm) Maximum panel weight = 55 lbs (25 kg) 24" recess Inset installation style H = 79 7/8" (2029 mm) W = 23 3/4" (603 mm) Frameless installation style H = 80" (2032 mm) plu
Planning Information 30" recess Inset installation style H = 79 7/8" (2029 mm) W = 29 3/4" (756 mm) Frameless installation style H = 80" (2032 mm) plus overlapping of the panel on the top W = 30" (762 mm) plus overlapping of the panel on both sides Minimum panel thickness = 5/8" (16 mm) * Maximum panel thickness = 1" (25 mm) Maximum panel weight = 77 lbs (35 kg) 36" recess Inset installation style H = 79 7/8" (2029 mm) W = 35 3/4" (908 mm) Frameless installation style H = 80" (2032 mm) plus overlapping of
Unpacking Unpacking Tx™ 20 1. Cut the straps and remove them. Tx™ 20 2. Press in the lug, tear or cut the carton on the edge and remove it. 3. Remove all styrofoam packing material from the sides and top. 7. Remove the safety transportation brackets and anti tipping device. Remove the packed cover strips and support strips from the appliance rear. 4. Remove the box with mounting parts. 5. Remove the ventilation grille. WARNING! Risk of injury and damage.
Unpacking Alternative possibility: Tilt the appliance slightly sideways. Cut off the marked area from the pallet. or Slide a two-wheeled cart between the appliance and packaging. Restrain the appliance to the cart with straps. Tilt the appliance onto the cart. Place the appliance carefully on the floor.
Standard Accessories Standard Accessories Depth adjustment aid 4 pcs. Door rack 3 pcs. Ventilation grille Top cover for the door panel attachment bracket anti tipping device 30 pcs. Retaining screws for installation 20 pcs. 8 pcs. 2 pcs. M6 x 12 Tx™ 15 Tx™ 15 16 pcs. Tx™ 15 Tx™ 20 20 pcs. Tx™ 10 SmartDeviceBox Includes component for Smartphone Connectivity DO NOT DISCARD! Forward to appliance user! TorxTM keys Panel support 10 pcs.
Blocking Mounting the anti tipping device in cabinets deeper than 24" Figure 1- 2 To ensure the compressor mounting plate reaches the anti tipping bracket in cabinets deeper than 24", a wooden spacer must be mounted between the appliance back and the wall. The anti tipping bracket will be fastened to the floor downwards and to the spacer backwards. WARNING! Be sure the wooden spacer is fastened securely to the floor.
Blocking for Safety Mounting the anti tipping device on concrete floors - Figure 4 - 5 Secure the appliance in place so it does not tip forward when the fully stocked door is opened. The anti tipping bracket is provided with the appliance. 1. Mark the center line of the appliance on the back wall. Align the anti tipping bracket center to this line. Wall WARNING! Be sure that there is no plumbing or electrical wiring located in this area which screws or drills could damage. 2.
Installation Safety Instructions and Warnings for Water Connection • Do not install the water connection while the appliance is connected to an electrical outlet. Appliance Installation Move the appliance towards the final position and leave enough space to work behind. • The connection to the water supply may only be made by a trained and licensed plumber. WARNING! Connect to potable water supply only. Water Connection Requirements • The water pressure must be in the range of 40-90 psi (2.8-6.2 bar).
Installation Insert the water filter as far as it will go with the front knobs in a horizontal position and turn clockwise until it snaps in. Remove the mounting strip from the attachment bracket, turn 180° and insert into the attachment bracket as far as it will go. Route the power cord towards the electrical outlet. Route the water line towards the water shut-off valve. IMPORTANT Complete the installation before switching on the device. Remove the tapes.
Installation Mounting the depth adjustment aid into the cover strips Align the appliance in depth. X = Recess front to appliance housing front (not cover strip) Inset 7/8" (22 mm) panel X = 2 5/ 8" (66 mm) Inset 3/4" (19 mm) panel X = 2 1/2" (63 mm) Inset 5/8" (16 mm) panel X = 2 3 / 8" (60 mm) Frameless X = 1 3 /4" (44 mm) or with the depth adjustment aid: The surface of the depth adjustment aid must be flush with the surface of the recess.
Installation Remove the transit supports using the Torx 25 key. Mount the ventilation grille with the grille segments tilted down. DANGER! Remove the depth adjustment aid before fastening the appliance in the recess. Risk of death or serious injury due to appliance tipping. Do not open the appliance door before the height adjustment is finished and the anti tipping bracket supports the appliance. Tx™ 15 Turn clockwise to raise the appliance.
Installation Push the mounting strip upwards. The bottom edge of the mounting strip must be aligned with the top edge of the adjacent cabinet door. Position the attachment bracket in the middle of the door panel, align horizontally and secure to the door panel using eight 4 x 14 screws. Inset installation style Frameless installation style Tx™ 15 IMPORTANT Risk of damaging the panel. Do not undershoot the minimum panel thickness (shaker style).
Installation Position the panel support strips with the top lug in the cut of the top attachment bracket. Align the strips parallel to the side edge of the panel and screw into place with ten 4 x 14 screws. IMPORTANT If the door has to be limited to a 90° opening angle, it must be done before the panel is mounted onto the appliance door. See chapter "Important Note for Changing over Door Hinges or Limiting the Hinges to a 90° Opening Angle" on page 24. Open the appliance door.
Installation Align the panel in its depth at the bottom. Align the panel in its vertical position if necessary. Loosen the screws, align the panel and tighten the screws. Use the Torx 20 key provided. Loosen the hex nuts and turn the adusting bolts with the Torx 15 key provided. Maximum adjustment: 15 mm (5/8") Align the panel horizontally with the long holes in the attachment bracket. Fasten the panel through the bottom attachment bracket with two screws 4 x 14. Tighten the hex nuts.
Installation Insert the panel supports into the support strips between panel and appliance door and screw into place with two screws M6 x 12 each. Hook the door cover strips at the front of the supports and snap in at the back.
Installation Adjust the brackets to the thickness of the toe kick panel. Click cover into place. Remove the backing foil and affix the toe kick panel. Check that there is no gap between the appliance air divider and the door air divider. IMPORTANT There will be a gap if the ventilation grille is fitted incorrectly.
Installation Please note in case of removing appliance from the recess If the appliance has to be removed from the recess again, please make sure you take account of the following. Insert the door racks. 1. Unload the appliance. 2. Disconnect the appliance from the power source. 3. Remove the mounted front panel from the appliance door. 4. Lower the appliance using the height adjustment unit. Insert the hooks of the rack into the openings of the clip-in strip at the desired height and push down.
Installation 25
For Service in the U.S. Liebherr Service Center Toll Free: 1-866-LIEBHER or 1-866-543-2437 Email: Service-appliances.us@liebherr.com PlusOne Solutions, Inc. 3501 Quadrangle Blvd, Suite 120 Orlando, FL 32817 For Service in Canada Liebherr Service Center Toll Free: 1-888-LIEBHER or 1-888-543-2437 www.euro-parts.ca EURO-PARTS CANADA 39822 Belgrave Road Belgrave, Ontario, N0G 1E0 Phone: (519) 357-3320 Fax: (519) 357-1326 *708585900* w w w. l i e b h e r r - a p p l i a n c e s .
