Installation Instructions Combined fridge-freezer for integrated use, door-on-door HC 10..
General safety information Contents 1 General safety information........................... 2 2 Transporting the appliance........................... 2 3 Setting up the device..................................... 2 4 Appliance dimensions................................... 4 5 Recess dimensions....................................... 4 6 Cabinet door................................................... 5 7 Air circulation in the kitchen cabinet........... 7 8 Reversing the door...........
Setting up the device WARNING Risk of fire due to refrigerant. The refrigerant contained within the appliance is environmentally friendly, but flammable. Leaking refrigerant can ignite. u Do not damage the pipes of the refrigerant circuit. WARNING Danger of fire and damage! u Do not place devices that give off heat, e.g. microwaves, toasters, etc. on the appliance.
Appliance dimensions 4 Appliance dimensions Fig. 2 Fig. 1 in. mm in. mm F 69 3/4 — 70 3/8 1772 — 1788 A 22 in. 559 mm G 22 — 22 3/4 560 — 578 B 21 7/16 in. 544 mm H C 69 11/16 in. 1770 mm min. 21 5/8, recom- min. 550, recommended 22 mended 560 D 27 3/8 in. 695 mm J min. 19 11/16 min. 500 E 5/8 in. 15 mm K min. 1 5/8 min. 40 L max. 3/4 max.
Cabinet door u Align the cabinets with a spirit level and a try square. If necessary level them by putting something underneath them. u Ensure that the floor and the side panels of the cabinet are at right angles to each other. 6 Cabinet door - Two doors are required for the kitchen cabinet: a top one for the fridge section and a bottom one for the freezer section. - The doors must be at least 5/8 in. (16 mm) and no more than 3/4 in. (19 mm) thick.
Cabinet door Fig. 3 The height of the freezer door is 24-24/32 in. (629 mm). u In order to cover the bottom section of the appliance: extend the plate height to 27-3/8 in. (695 mm). The thickness of the floor plate is normally 3/4 in. (19 mm). u In order to cover the front of the floor plate Fig. 3 (a): extend the plate height to 27-3/8 in. + 3/4 in. = 28-1/8 in. (695 mm + 19 mm = 714 mm). If no cabinet doors have yet been fitted the gap between the freezer section door Fig.
Air circulation in the kitchen cabinet u Total height of the cupboard (i.e. 70-3/8 in. (1788 mm)) plus thickness of the cover and floor plate (normally 3/4 in. (19 mm)) minus the height of the freezer cabinet door leaf (xxx in. (xxx mm)) as calculated above and minus the gap width (approximately 1/8 in. (3 mm)): 70-3/8 in. + 3/4 in. + 3/4 in. - xxx in. - 1/8 in. = 71-3/4 in. - xxx in. (1788 mm + 19 mm + 19 mm - xxx mm - 3 mm = 1823 mm - xxx mm) 7 Air circulation in the kitchen cabinet Fig.
Reversing the door Ventilation from underneath through the floor of the kitchen cabinet can be set up with the supplied ventilation grid Fig. 7 (3) or an air vent with at least a 31 in2 (200 cm2) cross section area. If you use the supplied ventilation grid Fig. 7 (1) please proceed as follows: Only undo the screw. Don't take it out. Check the screws and if necessary tighten them. Required tool: Fig. 8 Fig. 7 u Cut a hole 17-23/32 in. (450 mm) wide and 2-7/32 in.
Reversing the door Fig. 11 u Undo the screws on the hinges but do not remove them. Fig. 10 u Remove covers.
Reversing the door Fig. 12 CAUTION Hinges are spring-loaded and can cause pinching injuries! u Leave hinges open. u Removing the door: Push the door forward and then out, unhook it and put it to one side. Fig. 13 u Swap the hinges.
Reversing the door Fig. 16 * u Re-attaching the soft stop mechanism: Screw in the ball studs (1), tighten the retainer (2) and attach the soft stop dampers into the ball studs.* Fig. 14 u Swap the fixing bracket to the opposite side. Fig. 17 Fig. 15 u Check all screws and retighten if necessary. u Fit all covers except for the top left and the top right. Only fit the top covers after installing the appliance into the cabinet again.
Water connection* 9 Water connection* WARNING Electrical Shock Hazard! u Do not make the water connection while the appliance is connected to an electrical outlet. u Disconnect the water supply before connecting the water lines for the IceMaker. u The connection to the water supply may only be made by a trained and licensed plumber. WARNING Poisoning Hazard! u The water quality must comply with the drinking water regulations for the geographical area where the appliance is located.
Installing the appliance in the recess. The following accessories are available from Customer Services for installing the appliance in a recess: Set to fit divided cabinet fronts Set with covers for top hinges There is the risk of injury when doing this. Obey the safety instructions. Fig. 19 u Affix the water supply Fig. 19 (7) to the housing, if necessary, using the locking element Fig. 19 (10). Before fitting into the cabinet: u Check the whole water system for leaks.
Installing the appliance in the recess. Fig. 22 If the depth of the unit is less than 21-3/4 in. (553 mm) remove the spacers on the back of the appliance in order to be able to push the appliance completely into the recess. Removing the spacers may cause the appliance to use more energy as this reduces the ventilation cross-section. u Undo the screw and remove the spacers. Fig. 23 u Remove the top left cover and screw the fixing bracket in loosely. Fig.
Installing the appliance in the recess. With 5/8 in. (16 mm) thick cabinet side panels: u clip spacers on all hinges. u Remove the top left cover and screw the fixing bracket in loosely. Fig. 28 The width of the equalizer trim is 22 1/2 in. (572 mm). With a 22 in. (560 mm) wide recess: u cut the equalizer trim on both sides with a knife to fit the groove. With a recess width of between 22 in. (560 mm) and 22 1/2 in. (572 mm): u cut the equalizer trim on the hinge side with a knife to fit the groove.
Installing the appliance in the recess. u Fit the equalizer trim to the top of the appliance. If the hinge is on the left, slide the equalizer trim into the right hook. If the hinge is on the right, slide the equalizer trim into the left hook. Fig. 30 u Fasten the bottom left fixing bracket so that it does not protrude beyond the side panel. u Clip the stop onto the bracket. Fig. 31 u Fit the strip: place at the top under the bracket and stick to the side panel. The strip must not be shortened.
Installing the appliance in the recess. Fig. 33 u If necessary align the appliance using the adjusting feet. Fig. 32 u Push the appliance in until the handle side above the bracket and below the stop meets the front of the cabinet side panel. With 5/8 in. (16 mm)thick cabinet side panels the spacers on the hinge side must abut at the same time. With 5/8 in. (16 mm)thick cabinet side panels align the front edges of the hinges so that they are flush with the front of the cabinet side panel. Fig.
Installing the appliance in the recess. Fig. 35 u To fix the appliance in the recess: first hinge side up, then down, then in the middle. Then handle side down and finally handle side up. Fig. 36 u Remove the stop from the bracket on the handle side and dispose of it. Re-attach cover. u Re-attach the cover on the hinge side. u Break the stop at the bottom of the handle side off and dispose of it. Fitting the cover.
Installing the appliance in the recess. Fig. 39 u Undo the counter nuts and remove the crosspiece. Fig. 37 u Supporting the appliance at the bottom at the back: Insert the handle into the stabilization rail and push the stabilization rail into the appliance floor. Remove the handle and do the same with the second stabilization rail. Carry out the steps below for both doors: Fig. 38 u Close the door. u Check the default setting of 5/16 in. (8 mm). u Raise fitting aids to unit door height.
Installing the appliance in the recess. Fig. 42 u Remove the fitting aids, turn round and insert into the adjacent opening. Fig. 45 Fig. 43 u Align the unit door in the X and Y direction using the adjusting bolts. u Tighten the lock nuts. u Clip the cover on the crosspiece on the handle side. Fig. 46 Fig. 44 u Check the gap between the door and the surrounding unit doors u Attach the unit door and loosely screw the lock nuts onto the adjusting bolts.
Installing the appliance in the recess. Fig. 50 u Clip the top cover on. Fig. 47 u Align the front edge of the spring steel bracket parallel to the unit door edge and screw the bracket down tightly. Fig. 48 u Aligning the unit door in the Z direction: Undo the adjusting screw on the crosspiece and the screw on the spring steel bracket then move the door. Fig. 51 u Put the cover onto the spring steel bracket, fasten at the front, swivel towards the back and let it engage at the top and bottom. Fig.
Disposal of packaging 12 Connecting the appliance WARNING Electrical shock hazard! u Start-up should only take place once the appliance has been installed according to these instructions. u Electrically ground appliance. u Do not ground to a gas pipe. u Check with a qualified electrician if you are not sure the appliance is properly grounded. u Do not have a fuse in the neutral or grounding circuit. u Do not use an extension cord, power bar or a multiple socket adapter.
Connecting the appliance * Depending on model and options 23
For Service in the U.S.: Liebherr Service Center Toll Free: 1-866-LIEBHER or 1-866-543-2437 Service-appliances.us@liebherr.com PlusOne Solutions, Inc. 3501 Quadrangle Blvd, Suite 120 Orlando, FL 32817 For Service in Canada: Liebherr Service Center Toll Free: 1-888-LIEBHER or 1-888-543-2437 www.euro-parts.ca EURO-PARTS CANADA 39822 Belgrave Road Belgrave, Ontario, N0G 1E0 Phone: (519) 357-3320 Fax: (519) 357-1326 www.liebherr-appliances.com Part No.
