Use and Care Manual

NOTICE
Leakage water may damage the system!
u
Do not install this system on hot water lines. The
maximum operating temperature of the water in this
system is 100 °F (37.7 °C).
u
This system MUST be installed and used in compli-
ance with federal and local installation regulations.
u
Do not install under water hammer conditions. A water
hammer arrestor must be used to prevent water
hammering. If you are unsure how to check these
conditions, consult a professional installer.
u
Do not install with a water pressure greater than 90 psi
(6.2 bar). If your water pressure exceeds 80 psi, install
a pressure limiting valve. If you are unsure how to
check the water pressure, consult a professional
installer.
u
Protect against frost; if temperatures below 33 °F
(0.6 °C) are expected, remove the filter.
u
When used as indicated, the disposable filter
cartridges must be replaced every 6 months or when-
ever you notice a considerable decrease in the flow
rate.
q
Disconnect the appliance from the mains.
q
Close off the main water supply if the appliance has
already been connected to the tap.
q
Position appliance in front of the recess.
Fig. 36
u
Slice open the water hose Fig. 36 (7) located behind the
appliance both in front of and behind the connector
Fig. 36 (8) (90° to direction of hose).
When doing so, make sure the hose does not become
kinked and the cross-section of the hose remains round.
u
Connect the supplied exten-
sion hoses
Fig. 37 (1) to the
appliance hoses Fig. 37 (7) :
Slide the appliance hoses
into the connectors as far as
they will go (approx. 25/32 ''
(20 mm)).
Fig. 37
u
Pull the tray
Fig. 38 (4) out
until it catches.
u
Secure the module with 4
screws Fig. 38 (5) through
the recesses in the front
and directly through the
module in the back.
Fig. 38
u
Shorten hoses if necessary (90° to direc-
tion of hose). The hoses should be long
enough to allow the appliance to be
pulled out of the recess even when it is
connected to the water filter.
Make sure the hoses do not become kinked and the
cross-section of the hose remains round.
u
On the thin hose measure the inser-
tion depth (E) of 21/32 '' (17 mm) and
make a mark.
u
On the thick hose measure the inser-
tion depth (E) of 25/32 '' (20 mm) and
make a mark.
u
Insert the hoses
Fig. 39 (1) into
the water filter module as far
as they will go (i.e. to the mark
you made) past the point of
resistance.
Fig. 39
Note
u
If you need to disassemble the unit: Push back the dark
grey ring on the connector and hold it in this position.
While still holding the ring back, briefly push the hose
into the connector, then pull it out.
u
Insert the power cable into the socket (see 4.10) .
u
Connect appliance to the water supply (see 4.5) .
u
Make sure the filter is leak-tight and no water is coming
out.
u
Place the tray cover
Fig. 41 (3) into position.
Fig. 40
Fig. 41
u
Remove the film from the water filter
Fig. 41 (6) .
u
Insert the water filter Fig. 41 (6) and turn it approximately
100° to the right until it locks into position.
u
Place the cover on the filter Fig. 41 (2) .
u
Slide the tray in.
u
Write the date of the next filter replacement on the
supplied adhesive label Fig. 41 (9) and affix it to the
module.
Note
New water filters may contain particulate matter.
u
Do not consume or use ice cubes produced within 72
hours after replacing the filter.
w
The water filter is now ready for use.
Start-up
16 * Depending on model and options