Use and Care Manual

u
Unscrew the bearing pin
Fig. 12 (42) , with disc
Fig. 12 (43) and positioning foot Fig. 12 (44) , in an
upwards direction.
u
Lift off plug Fig. 12 (41) .
u
Unscrew Fig. 12 (46) bearing bracket Fig. 12 (45) .
u
Completely unscrew the grub screw Fig. 12 (60) and
screw it into the opposite side of the bearing bracket
until it is externally flush with the bearing bracket.
u
Unscrew bearing part Fig. 12 (48) , turn it 180° and
tighten Fig. 12 (49) it to the inside.
u
Insert plug Fig. 12 (41) back into the other hole.
u
Carefully lift off the cover on the handle side Fig. 12 (47)
and move it to the opposite side.
u
Using a cordless screwdriver if necessary, again
secure the bearing bracket Fig. 12 (45) on the new hinge
side tightly (to 4 Nm).
u
Screw complete bearing pin Fig. 12 (42) , with disc and
positioning foot, back into place again.
u
Tighten grub screw Fig. 12 (60) .
4.3.7 Swapping the handles
For both the upper and lower door:
Fig. 13
u
Pull plugs Fig. 13 (50) out of the door bearing bushes
and move them to the other side.
u
Detach the door handle Fig. 13 (52) , plug Fig. 13 (53) and
pressure plates* Fig. 13 (54) and move them to the
opposite side.
u
When fitting the pressure plates on the opposite side,
make sure they engage correctly.*
4.3.8 Fitting the lower door
u
Position the lower door from above onto the lower
bearing pins
Fig. 12 (42) .
u
Close the door.
u
Place the plastic cap Fig. 11 (33) back onto the center
bearing bracket Fig. 11 (31) .
u
Insert the center bearing pin Fig. 11 (32) on the new
hinge side through the center bearing bracket
Fig. 11 (31) into the lower door.
u
Place disc Fig. 11 (34) onto the center bearing pin
Fig. 11 (32) .
4.3.9 Fitting the lower soft stop damper
Fig. 14
u
Loosen cover
Fig. 14 (26) from the panel Fig. 14 (20) and
insert on the other side.
u
With the hinge of the soft stop unit facing the door
hinge side, engage the soft stop unit (A) and swivel
inwards (B)
w
The holes on the left and right must lie exactly above
each other
u
Tighten soft stop unit (2 x Torx® 15) Fig. 14 (25) .
Fig. 15
u
Hook panel Fig. 15 (20) into the damper bracket such
that the detent hooks are pointing forwards and the
front side is facing the appliance.
u
Pull damper bracket Fig. 15 (24) towards bearing
bracket and insert bolt Fig. 15 (23) from above such that
the square is resting in the recess.
u
Position cover Fig. 15 (21) and snap in.
w
Check that the cover is positioned correctly such that
the door can close properly and the bolt is secured
u
Remove locking device Fig. 15 (22) by twisting it.
u
Snap panel Fig. 15 (20) into place on the door.
u
Close the lower door.
4.3.10 Fitting the upper door
u
Place the upper door onto the center bearing pin
Fig. 11 (32) .
u
Insert the upper bearing bracket Fig. 8 (12) on the new
hinge side into the door.
u
Tighten the upper bearing bracket (to 4 Nm)(2 x Torx®
25) Fig. 8 (13) . Make preliminary holes (optional) or use
a cordless screwdriver.
Start-up
* Depending on model and options 9