oo | ® Page 9 Thursday, June 9, 2022 1:51 PM INSTALLATION 9 INSTALLATION Before Installing Installation Overview Please read the following installation instructions first after purchasing this washer or transporting it to anther location. © Choosing the Proper Location @ Unpacking and Removing Shipping Material © Connecting the Inlet Hoses @ Connecting the Drain Hose @ Leveling the Washer @ Final Installation Check OY £4 WARNING Moving or installation of the appliance requires two or more people.
Page 10 Thursday, June 9, 2022 1:51 PM 10 INSTALLATION | ® 4b WARNING « Certain internal parts are Intentionally not grounded and may present a risk of electric shock only during servicing. Service personnel Do not contact the following parts while the appliance is energized: pump, valve, motor, control board. Tools Leaded Pliers @ Flat-Blade Screwdriver @® Level Choosing the Proper Location Check the following requirements for the install location before installing the washer.
© | ® Page 11 Thursday, June 9, 2022 1:51 PM el] INSTALLATION 11 Dimensions and Clearances 174" (0.5 cm) Stacking or Pedestal Installation The washer can be stacked under a dryer or on top of a pedestal or pedestal washer. A ~B Gide Dimensions and Clearances 33 1/4" 1/2" (196.8 cm) n|lm|o|n|w|> 144" (0.5 cm) NOTE Refer to the Instructions packaged with the optional pedestal kit before stacking appliance on pedestal.
Page 12 Thursday, June 9, 2022 1:51 PM 12 INSTALLATION | ® the washer. Install the caps In the holes left by the bolt assemblies. 4) CAUTION Once removed, save the bolt assemblies for future use. To prevent damage to Internal components, do not transport the washer without reinstalling the shipping bolts. Failure to remove shipping bolts and retainers may cause severe vibration and noise, which can lead to permanent damage to the washer.
| ® Page 13 Thursday, June 9, 2022 1:51 PM | ® INSTALLATION 13 * Let the water drain into a bucket, and check the water temperature to make sure you've connected the hoses to the correct faucets. 4 Awash the inlet hoses to the back of the washer. + Attach the hot water inlet hose to the hot water inlet on the back of the washer. Attach the cold water Inlet hose to the cold water inlet on the back of the washer. « Tighten the fittings securely.
| ® Page 14 Thursday, June 9, 2022 1:51 PM 14 INSTALLATION el] hoses with the provided tle strap @ (ribbed side on inside), Using the Laundry Tub to Drain 1 Clip the end of the hose into the elbow bracket. Connect the elbow bracket @ within 4 inches (10 cm) of the end of the drain hose. If the drain hose is extended more than 4 inches (10 cm) beyond the end of the elbow bracket, mold or microorganisms could spread to the inside of the washer.
| ® Page 15 Thursday, June 9, 2022 1:51 PM | ® INSTALLATION 15 2 Adjust the leveling feet. » Turn all 4 leveling feet in one direction to raise the washer or the other direction to lower it, Ep, cons a 3 Check the level again. Push or rock the top edges of the washer gently to make sure the washer does not rock. If the washer rocks, readjust the leveling feet. 4 Tighten the lockouts @ » Turn the lockouts counterclockwise and tighten them when the washer is level.
Page 16 Thursday, June 9, 2022 1:51 PM 16 INSTALLATION el] 4b WARNING « Do not use an adapter or extension cord. Dong 50 may result in serious injury, fire, electric shock, or death. For best performance, plug the appliance into its own individual outlet. This helps prevent overloading house wiring circuits which could cause a fire hazard from overheated wires. If necessary, use a new, UL-listed extension cord with a 3-prong {grounding} plug rated at no less than the branch circuit.
