WD-1374(6)F(H)B WD-1274(6)F(H)B WD-1174(6)F(H)B WD-1074(6)F(H)B WD-8074F(H)B
P roduct Feature 40% n Jumbo drum LG’s jumbo drum can wash about 40% more load than conventional washing machines. A bigger drum improves the wash performance. n More economical by Intelligent Wash System Intelligent Wash System detects the amount of load and water temperature, and then determines the optimum water level and washing time to minimize energy and water consumption.
W arnings READ ALL INSTRUCTIONS BEFORE USE WARNING! ! For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric shock, or to prevent property damage, personal injury, or loss of life. IMPORTANT SAFETY INSTRUCTIONS WARNING : To reduce the risk of fire, electric shock, or injury to persons when using the washer, follow basic precautions, including the following: • Do not install or store the washer where it will be exposed to the weather.
S pecification Power plug If the supply cord is damaged, it must be replaced by the manufacturer or its service agents or a similarly qualified person in order to avoid a hazard. Drawer (For detergent and fabric softener) Control panel Drain hose Door Drum Lower cover Adjustable feet Drain pump filter Lower cover cap Drain plug : Front loading washing machine : 220-240V~, 50Hz : 600mm(W) 600mm(D) 850mm(H) : 63kg : 7.
I nstallation Install or store where it will not be exposed to temperatures below freezing or exposed to the weather. Properly ground washer to conform with all governing codes and ordinances. The base opening must not be obstructed by carpeting when the washing machine is installed on a carpeted floor. n Transit bolts The appliance is fitted with transit bolts to prevent internal damage during transport. n Removing transit bolts 1.
I nstallation n Installation place requirement Level floor : Allowable slope under entire washer is 1˚ Power outlet : Must be within 1.5 meters of either side of location of washer. Do not overload the outlet with more than one appliance. Additional Clearance : For wall, door and floor modeling is required. (10cm : rear /2cm:right & left side) Drain Hose Washer Laundry Tub approx. 2cm Do not place or store laundry products on top of washer at any times. They can damage the finish or controls.
I nstallation n Electrical connection 1. Do not use an extension cord or double adapter. 2. If the supply cord is damaged, it must be replaced by the manufacturer or its service agents or similarly qualified person in order to avoid a hazard. 3. Always unplug the machine and turn off the water supply after use. 4. Connect the machine to an earthed socket in accordance with current wiring regulations. 5. The appliance must be positioned so that the plug is easily accessible.
nstallation I n Installation of drain hose ca. 100 cm min. 60 cm max. 100 cm ca. 145 cm • When installing the drain hose sink, secure it tightly with a string. ca. 105 cm • Proper securing the drain hose will protect the floor from damage due to water leakage. Laundry tub ca. 100 cm Hose Retainer max. 100 cm ca. 105 cm min. 60 cm ca. 145 cm max. 100cm min. 60cm Tie strap max. 100cm min. 60cm • The drain hose should not be placed higher than 100 cm above the floor.
I nstallation n Level adjustment 1. Adjustable the washing machine properly prevents excessive noise and vibration. Install the appliance on a solid and level floor surface, preferably in a corner of the room. Adjustable feet Higher 2. If the floor is uneven, adjust the adjustable feet as required. (do not insert pieces of wood etc. under the feet) Make sure that all four feet are stable and resting on the floor and then check that the appliance is perfectly level.
C are before washing n Caring before washing 1. Care Labels Look for a care label on your clothes. This will tell you about the fabric content of your garment and how it should be washed. 2. Sorting To get the best results, Sort clothes into loads that can be washed with the same wash cycle. Water temperature and spin speed and different fabrics need to be washed in different ways. Always sort dark colors from pale colors and whites.
A dding detergent n Adding detergent and fabric softener 1. The Dispenser Drawer 3. Detergent dosage MAX • The detergent should be used according to the instruction of the detergent manufacture. max • If too much detergent is used more than the recommended amount, too many suds can occur and this will decrease the washing result or cause heavy load to the motor. (Causing a malfunction) • Use powder detergent only for the front loading washer.
F unction n Recommended courses according to the laundry type Fabric Proper Load Water in Liter Energy in kWh Time in Minutes First check if Pre Wash laundry is machine 95˚C Eco washable. (60˚C, 50˚C, Rinse+ (white cotton, linen 40˚C) Bio towel and sheets...) Rapid Rating 85 2.74 158 Coloureds Color fast gaments Pre Wash (shirts, night dresses, Eco 40˚C pajamas...)and Rinse+ (50˚C, 60˚C, lightly soiled white Cold, 30˚C) Bio cotton(underwear...) Rapid Rating 75 0.
H ow to use washer 1. For use in the initial programme (Coloureds) 2. Manual Selecting • Press the Power button to start. • Press the Power button to start. • Press the Start/Pause button. • Select the conditions which you want to use, by pressing each button. For selecting the each conditions, please refer to the page41~page45 • Initial condition - Wash : Only main wash - Rinse : 3 times - Spin : 800 rpm - Water temperature : 40˚C - Program : Coloureds 40 • Press the Start/Pause button.
H ow to use washer (1) (2) (1) Button : Option (2) Button : Spin (3) Button : Temp. (3) (4) (5) (6) (7) (4) Child Lock (5) Button : Time Delay (6) Button : Rapid Option • By pressing the Option button, the Option function can be selected. - Bio - Rinse+ - Eco - Pre Wash (8) (9) (7) Button : Start/Pause (8) Dial : Program (9) Button : Power 3. Eco • By selecting Eco function, the water temperature is reduced and washing time is lengthened. So you can economize in your consumption of energy.
H ow to use washer Spin [WD-8074F(H)B] [WD-1074(6)F(H)B] [WD-1274(6)F(H)B] [WD-1374(6)F(H)B] [WD-1174(6)F(H)B] • By pressing the Spin button, the spin speed can be chosen. 1. Spin selection • Spin speed is available according to the program as follows.
H ow to use washer Water Temp. • WD-1374(6)F(H)B - Whites / Coloureds 800U 1100U 1300U Rinse HoldU No SpinU 400U 600 - Synthetic 800U 1100U Rinse HoldU No SpinU 400U 600 - Delicate 400U 600U 800U Rinse HoldU No Spin - Wool / Hand Wash 400U 600U 800U 1100U Rinse HoldU No Spin 2. No spin • If no spin is selected, the washer stops after draining water. If lamp turns on, that function has been selected. 3.
H ow to use washer Child Lock Time Delay Time Left If you want to lock all the buttons to prevent operation by a child or infirm persons, this function can be used. 1. Child Lock • Child Lock can be set by pressing the Temp. button and Time Delay button simultaneously. Time Left • When child lock is set, all buttons are inoperable. • To deactivate Child Lock system, press Temp. and Time Delay button simultaneously again. Time Left 1.
H ow to use washer Start/Pause Rapid • By pressing the Rapid button, Rapid function is selected. 1. Rapid 1. Start • Rapid function reduces the whole time including the washing and rinsing time about by half an hour. • Rapid is available in Whites, Coloureds program. If lamp turns on, that function has been selected. • This Start/Pause button is used to start wash cycle or pause the cycles. Program 2. Pause • If temporary stop of wash cycle is needed, press the Start/Pause button.
H ow to use washer Display 3. Completion of washing • When washing cycle is completed, “ ” is displayed on the “Multi display”. 1. Special function display • When child lock is selected, the “ ” is displayed. • When time delay is selected, it shows the remaining times to finish the selected program. 2. Self diagnose display • If the washer has a trouble, the trouble type is displayed. “ ” : Sensing water pressure error “ ” : Problem of overfilling water “ ” : Door is not closed “ ” : Over load in moter.
M aintenance ❋ Before cleaning the washer interior, unplug the electrical power cord to avoid electrical shock to avoid electrical shock hazards. n The water inlet filter -" " error message will blink on the control panel when water does not enter the detergent drawer. - If your water is very hard or contains traces of lime deposit, the water inlet filter may become clogged. It is therefore a good idea to clean it from time to time. 1. Turn off the water tap. 2. Unscrew the water inlet hose. 3.
M aintenance n Dispenser drawer ❋ After a while detergents and fabric softeners leave a deposit in the drawer. • It should be cleaned from time to time with a jet of running water. • If necessary it can be removed completely from the machine by pressing the catch downward and by pulling it out. MAX • To facilitate cleaning, the upper part of the fabric softener compartment can be removed.
M aintenance n Cleaning your washer 1. Exterior Proper care of your washer can extend its life. The outside of the machine can be cleaned with warm water and a neutral non abrasive household detergent. Immediately wipe off any spills. Wipe with damp cloth. Try not to hit surface with sharp objects. ❋ IMPORTANT: Do not use methylated spirit, diluents or similar products. 2. Interior Dry around the washer door opening, flexible gasket and door glass.
roubleshooting guide T ❋ This washing machine is equipped with automatic safety functions which detect and diagnose faults at an early stage and react appropriately When the machine does not function properly or does not function at all, check the following points before you call the Service Department. Symptom Possible Cause Solution Rattling and clanking noise • Foreign objects such as coins or safety pins maybe in drum or pump. Stop washer and check drum and drain filter.
T roubleshooting guide Symptom Washer does not start Possible Cause • Electrical power cord may not be plugged in or connection may be loose. Make sure plug fits tightly in wall outlet. • House fuse blown, circuit breaker tripped,or a power outage has occurred. Reset circuit breaker or replace fuse. Do not increase fuse capacity. If problem is a circuit overload, have it corrected by a qualified electrician. Turn on water supply tap. • Water supply tap is not turned on.
roubleshooting guide T Symptom Possible Cause Solution • Water supply is not adequate in area • Water supply taps are not completely open. • Water inlet hose are kinked. • The filter of the inlet hose clogged. Check another tap in the house. Fully open tap. • Drain hose is kinked or clogged. • The drain filter is clogged. Clean and straighten the drain hose. Clean the drain filter. • Load is too small. • Load is out of balance. • The appliance has an imbalance detection and correction system.
Warranty conditions for washing machine 1. The warranty period begins on the purchase date and is valid for 12 months. Begin of warranty period is proven if, the buyer submits purchase receipt together with the warranty card, filled in and signed by the seller. The serial number of the product must agree with the number entered onto the warranty card. 2.
54
P/No.
