PLASMA TV OWNER'S MANUAL Please read this manual carefully before operating your set. Retain it for future reference. Record model number and serial number of the set. See the label attached on the back mation to your dealer when you Model number : Serial number : P/NO : 3828VA0468A (RF043B, cover require and quote this infor- service.
Safety Warnings Instructions Safety Safety Use the set at the - lower than the altitude of 6562 feet place (2000m) get the best quality of picture and to sound. W WARNING Do not place the sources such This may - Do not or any set in direct heat cause a use registers, sunlight or stove and near heat so on. damp place such as likely to get wet.
Safety Warnings * Safety instructions have two kinds of WARNING NOTES information, and each meaning of it is as below. The violation of this instruction may cause serious The violation of this instruction may cause light injuries injuries and even damage or death. of the product. Take care of under danger that may happen specific condition. NOTES Never touch the power - This may cause an plug with wet hand. a Ensure the power cord doesn't trail like a heater.
Contents Contents Contents Time Menu Safety Warnings SafetyInstructions.......................2~3 Introduction RemoteControlKeyFunctions................6 LocationandFunctionofControls . . . . . . . . . . .7~8 Options SettingtheClock.........................24 SettingtheOn/OffTimer...................24 AutoSleep..............................24 SleepTimer.............................24 Special Menu Options ChildLock..............................
Introduction Introduction What is a Plasma Display ? If voltage is inputted to gas in glass panels, ultraviolet rays is outputted and fused with a fluorescent light is emitted. A Plasma Display is a next generation flat Display using this phenomenon. 160° Wide - A Plasma angle substance. At this moment, range of vision Display provides than 160° more angle range of vision so that you get can without distortion from any picture a direction.
Introduction Remote Control Control - - When Functions Key using the remote control aim it at the remote control sensor of the set. maybe a defect in consecutive operation of remote control in specified brightness according There's MUTE off. Switches the sound Selects the POWER switches the set off to standby. on or MULTIMEDIA RGB or DVI modes. from standby. MUTE on on from standby or POWER Component, switches the set to this set feature.
Introduction Location and Function of of Controls Controls ON/OFF TV/AV MENU VOL PR VOL PR or TV/AV MENU Main Power Button MENU Displays on screen menus one by one. Exits the current menu. Memorizes menu changes. Remote Control Sensor TV/AV Button Selects the RGB or played, Power Standby Indicator Illuminates red in standby mode, Illuminates green when the set is turned on TV, AV, Component, DVI modes. If OSD is disselects menu item.
Introduction Location and Function of of Controls Controls AV2 S-VIDEO VIDEO L/MON 8 AUDIO R AC INPUT COMPONENT REMOTE RS-232C INPUT CONTROL (CONTROL/SERVICE) AUDIO INPUT DVI INPUT INPUT 2 MONITOR OUTPUT COMPONENT INPUT 1 A/V INPUT1 R VIDEO 1 2 Antenna RGB INPUT 3 L AUDIO R S-VIDEO L/MOND AUDIO VIDEO 4 5 6 1. CONTROL LOCK / REMOTE CONTROL 6. ANTENNA INPUT 2. RS-232C 7. POWER CORD SOCKET INPUT(CONTROL/SERVICE) Connect to the RS-232C port on a PORT PC.
Installation External V iewing Setups Equipment Viewing Setups Antenna Connection - Be careful for the bronze wire not to be bended in Apartments (connecting to wall antenna connecting to antenna input port.
Installation External Watching After - V iewing Setups Equipment Viewing Setups Cable TV subscribing for a local cable TV station and For further information of cable - TV, installing a converter you can watch cable TV. contact the local cable TV station. < Back panel of the set To watch cable TV > 1. Use the TV/AV button select AV1 or on the remote control to AV2. 2. Tune to cable service provided channels using the cable box.
Installation DVD Watching How to connect < Back panel of the set > Connect DVD video outputs to Y, PB, PR of COMPONENT INPUT and audio outputs to Audio sockets of AUDIO INPUT. How to use 1. Turn on the DVD 2. Use TV/AV player, and insert a DVD. MULTIMEDIA button or on the remote AC control to select Refer to the Component 1 or Component 2. DVD player's manual for operating COMPONENT COMPONENT A/V INPUT1 INPUT 1 R instructions.
Installation External Connecting - - - - - V iewing Setups Equipment Viewing Setups PC To enjoy vivid picture and sound, connect a PC to the set. Avoid keeping a fixed image on the set's screen for a long period of time. The fixed image may become permanently imprinted on the screen; use a screen saver when possible. Connect PC to the RGB INPUT(PC INPUT) or DVI INPUT(DIGITAL RGB INPUT) port of the set; change the resolution output of PC accordingly.
Installation Displayable Monitor RGB / DVI mode Resolution RGB / DVI mode Horizontal Vertical Frequency(KHz) Frequency(Hz) 31.468 70.09 37.861 85.08 31.469 70.08 640x350 848x480 852x480 800x600 832x624 Resolution Horizontal Vertical Frequency(KHz) Frequency(Hz) 31.468 70.09 37.861 85.08 31.469 70.08 640x350 720x400 640x480 Specification Specification 720x400 37.927 85.03 37.927 85.03 31.469 59.94 31.469 59.94 35.000 66.66 35.000 66.66 37.861 72.80 37.861 72.
Installation Accessories MUTE POWER TV/AV MULTIMEDA LIST ARC I/II MENU PR OK VOL VOL PR 123 456 7 PSM 89 SSM 0 SPLIT ZOOM PP/DW REVEAL SLEEP PIP PR+ TEXT/ ? LG TV WIN.SIZE PIP PR- 1.5V POSITION HOLD 1.
Installation Installation ? The set ? Install this set ? This set is can Options Options be installed in different ways such as on a wall, or on a desktop etc. only in a location where adequate ventilation is available. designed so that it can be mounted either Wall Mount: Horizontal Installation ? ? The set can be installed on a wall as on a or vertically. Desktop shown above. (For further information, refer to the optional 'Wall Mounting Bracket Installation and Setup Guide'.
Operation Turning Turning When - using Turning on the remote the set just 1. Connect power cord 2. Press the the Set Set on on control, aim it on sensor on correctly. the set on or the set. At this moment, the set is switched to press the POWER, TV/AV, MULTIMEDIA, PR remote control and then the set will switch Turning on 1. If the set the set was Press the ? 2. If the set Press the ? (power cord is still turned off with the ON/OFF button was the set.
Operation Channel Channel Menu Auto - Options Options Programme Tuning All stations that be received are stored by 1. Press the MENU button and then use Δ / can this method. It is recommended that you use auto programme during installation of this set. 2. Press the Γ button and then Δ button to select the STATION Ε menu. STATION 4.
Operation Channel Channel Menu Fine - Tuning Normally 1. Options Options fine Repeat tuning is only necessary if the 'Manual programme 2. Press the Γ button and then Δ 3. Press the Φ / Γ reception tuning' steps / Ε is poor. 1 to 2. button to fine tune for the best picture Auto programme Manual programme PICTURE Programme and sound. edit Favourite programme SOUND 4. Press the OK button. 5. STATION button to select Fine.
Operation Edit Programme - This function enables you to delete or skip the stored programmes. Also you can move gramme numbers or copy a blank station data into the selected programme number. 1. Press the MENU button and then use Δ / Ε button to select the STATION 2. Press the Γ button and then Δ / Ε button to select Programme edit. 3. Press the Γ button to display the Programme edit some stations to other pro- menu. Programme 0- menu.
Operation Picture Menu PSM - - Options Options (Picture Status Memory) This function adjusts the set to the best picture appearance. adjusting picture options (contrast, brightness, colour, sharpness automatically changed to User. When is and tint (NTSC input only)) manually, PSM 1. Press the PSM button Each press of the PSM button ? changes You ? Picture the - - You can screen display as shown below.
Operation sRGB - (RGB[PC], DVI[PC] When the set the was equal image mode only) connected to external equipment with sRGB function, It's adjusted a colour difference to 1. Press the MENU button and then button to select the PICTURE use Δ / Ε 2. Press the Γ button and then use Δ / Ε 3. Press the Γ button and then use menu. button to select sRGB. STATION PSM PICTURE CSM sRGB SOUND Δ / Ε button to select On or Off. TIME 4. Repeatedly display each other.
Operation Sound Sound Menu SSM - - Options Options (Sound Status Memory) This function lets you enjoy the best sound without any special adjustment because the set automatically selects the appropriate sound option based on the program content. When adjusting sound options (treble and bass) manually, SSM is automatically changed to User. 1. Press the SSM button. 2. Press the SSM button to select your desired sound.
Operation Stereo / Dual - When tion Reception programme is selected, the sound information for the station appears after the programme number and sta- a name disappear. On Screen Display Press the I/II button to received broadcast state. Broadcast On Mono MONO Stereo STEREO Dual DUAL I screen Display Mono Sound Selection In stereo if the stereo reception I/II button twice. In signal is weak, you can switch to mono by pressing the reception the depth of sound is improved.
Operation T ime Menu Setting the Clock If current time - Options Options setting is erased by a power 1. Press the MENU button and then use Δ ton on failure, if TV is unplugged or if the set is turned off with the ON/OFF but- the set, reset the clock. / Ε button to select the TIME menu. STATION Clock Γ -- : -- Off time PICTURE 2. Press the Γ button and then use Δ / Ε button to select Clock. 3. Press the Γ button and then use Δ / Ε button to adjust the hour. 4.
Operation Menu Special Special Options Options Child Lock The set - be set up can so that it only can be used with the remote control. 1. Press the MENU button and then Δ / Ε button to select the SPECIAL menu. STATION Language Child lock 2. Press the Γ button and then Δ / Ε button to select Child lock. 3. Press the Γ button and then Δ / Ε button to select On PICTURE Off Low power SOUND or ΓOn ISM Method Set ID Off. Demo TIME 4.
Operation Special Special Menu Options Options Low Power - This is the function to reduce the power 1. Press the MENU button and then consumption use Δ / Ε of the set. button to select the SPECIAL menu. STATION Language Child lock 2. Press the Γ button and then 3. Press the Γ button and then button to select Low power. use Δ / Ε use Δ / Ε button to select On or PICTURE ISM Method SOUND Set ID Low power Off. ΓOn Off Demo TIME 4.
Operation Screen Screen Menu Auto - Options Options mode adjustment (RGB [PC] Automatically adjusts picture position 1. Press the MENU button and then only) and minimizes / Ε use Δ image shaking. button to select the SCREEN menu. STATION Auto config. Γ To set Γ Φ ARC 2. Press the button and then Γ use Δ / Ε button to select Auto config.. PICTURE Manual SOUND 3. Press the Γ button to start Auto ? When Auto ? If the Position config.. config. Reset TIME config.
Operation Screen Screen Menu Manual - - mode Configure (RGB [PC] If the isn't clear after auto picture phase manually. To correct the screen Options Options only) adjustment and especially that characters are still trembling, adjust the picture size, adjust Clock. 1. Press the MENU button and then Δ / Ε button to select the SCREEN menu. STATION Auto config. ARC 2. Press the Γ button and then Δ / Ε button to select Manual config.. PICTURE Manual SOUND 3.
Operation Luminance Noise Reduction - - You can select On (option) Off to reduce the picture following mode: Component 480i/576i. or noise which may appear on the screen during watching the TV. This function works in the TV, AV1, AV2 or 1. Press the MENU button and then use Δ / Ε button to select the SCREEN menu. STATION Screen adj. ARC 2. Press the Γ button and then use Δ / Ε 3. Press the Γ button and then use Δ / button to select YNR.
Operation PIP - - (Picture-in-Picture) (Picture-in-Picture) Feature PIP lets you view 2 different inputs (sources) on your set screen at the It's not available to use this function in TELETEXT mode. Watching time. PIP Press the PIP/DW button to show the sub ? same Each press of PIP/DW button changes picture. the screen display as shown below. PIP DW1 DW2 Off Selection for Sub Picture Programme Press the PIP PR + /- button to select a Moving programme for the sub picture.
Operation eletext (option) Teletext T (option) - Teletext TOP (or text) is an optional function, therefore only the set with the teletext system can receive the teletext broadcast. - - Teletext is a free service broadcast by most TV stations which gives up-to-the-minute television programmes, share prices and many other topics. The teletext decoder of this set can support the SIMPLE, TOP and FASTEXT consists of TEXT are information on news, weather, systems.
Operation FASTEXT The teletext pages are colour coded along the bottom of the pressing the corresponding coloured button. screen and are selected by Page selection 1. Press the 2. You button to select the index page. are colour coded i select the pages which coloured buttons. 3. 4. can the bottom line with the along Corresponding to the SIMPLE text mode, you can select a page by entering digit page number with the NUMBER buttons in FASTEXT mode.
Miscellaneous External Control Control Device Setup - Connect the RS-232C input jack to an external externally. control device (such as a computer or an A/V control system) and control the set's functions How to connect external control ? Connect the serial ? RS-232C connection cables ? The set remote control and front computer or Back panel to the RS-232C jack on the supplied with the set. panel controls (except main power) will Monitor back panel.
Miscellaneous Set ID - - Use this function to specify a set ID number. Mapping 1'. See page 38. Refer to 'Real Data 1. Press the MENU button and then use the Δ button to select the SPECIAL / Ε menu. STATION Language Child lock 2. Press the Γ button and then 3. Press the Γ button and then use Δ / Ε use button to select Set ID. Φ / Γ button to adjust PICTURE ISM Method SOUND Set ID Low power Set ID to choose the desired Γ 1 Demo TIME monitor ID number. SPECIAL ? 4.
Miscellaneous 01. Power 04. Screen Mute (Command Γ To control Power On/Off of the Monitor. Γ To select mute on/off. Transmission Transmission 2 (Command : a) [k][a][ ][Set ID][ ][Data][Cr] Data 0 d) : [k][d][ ][Set ID][ ][Data][Cr] Power Off : screen 2 1:PowerOn Data 0 : Screen mute off 1 : Screen mute (Picture on) (Picture off) on Ack Ack [a][ ][Set ID][ ][OK][Data][x] [d][ ][Set ID][ ][OK][Data][x] Γ To show Power On/Off. Transmission 05.
Miscellaneous 09. Colour You can 2 (Command Γ To adjust the also screen adjust i) : 14.PIP/DW(Command2:n) Γ To control the PIP (Picture In picture)/DW. colour. colour in the PICTURE You menu. on Transmission the PIP/DW button menu. [k][n][ ][Set ID][ ][Data][Cr] Min:0~Max:64 * using in the PIP/DW or Transmission [k][i][ ][Set ID][ ][Data][Cr] Data also control the PIP/DW can the remote control Refer to 'Real data mapping 1'. See page 38.
Miscellaneous 17. Treble (Command 2 22. Green :r) Γ To adjust treble. You can also adjust menu. w) Transmission [k][w][ ][Set ID][ ][Data][Cr] [k][r][ ][Set ID][ ][Data][Cr] Data Min:0~Max:64 * : Γ To adjust green in colour temperature. treble in the SOUND Transmission Data 2 Adjustment (Command Refer to 'Real data Min:0~Max:3C Refer to 'Real data * mapping 1'. See page 38. Ack 3'. See page 38. mapping Ack [w][ ][Set ID][ ][OK][Data][x] [r][ ][Set ID][ ][OK][Data][x] 23.
Miscellaneous Data 26. ISM Method (Command 1 : j, Command 2 Γ To control the ISM method. You Method in SPECIAL : Min:0~Max:14(1Eor20) Refer to 'Real data mapping * p) 1'. Ack also can adjust ISM [t][ ][Set ID][ ][OK][Data][x] menu. Transmission 31. Auto Configure (Command 1 : j, [j][p][ ][Set ID][ ][Data][Cr] Data 0 : 1 : Normal Mode 2 : White Wash 3 : Orbiter Command 2 : u) Γ To adjust picture position and minimize image shaking Inversion automatically.
Miscellaneous IR Code Code (NEC (NEC Format) How to connect Γ Connect your wired remote control to the Remote Control Remote Control IR Code port on the Monitor. (NEC Format) Γ Output waveform Single pulse, modulated with 37.
Miscellaneous Code 00H Note PR+ (Δ) (Ε) VOL+ (Γ) VOL- (Φ) R/C Button PR- R/C Button 08H POWER R/C Button C4H POWER ON Discrete IR Code C5H POWER OFF Discrete IR 09H MUTE R/C Button 10H Number 11H Number 12H Number 13H Number 14H Number 15H Number 16H Number 17H Number 18H Number 19H Number 0BH TV/AV R/C Button 98H MULTIMEDIA R/C Button BFH COMPONENT1 Discrete IR Code D4H COMPONENT2 Discrete IR Code C6H DVI Discrete IR Code D5H RGB Discrete IR Code 0
Miscellaneous Notes Owner's Manual 41
Miscellaneous Checklist Checklist Troubleshooting Troubleshooting No picture & ? Check whether the set is turned ? Power cord inserted into wall outlet? on. No sound ? another was ? Sound muted? Press MUTE button. Check to causing ? The remote control see to p.6) No new batteries. as the (Refer to image is muted p.6) during the startup process of picture has not appeared Please contact your service centre, if the minutes.
Miscellaneous Product Specifications MODEL Width RT-42PX10/11/H RT-42PX20/H (inches / mm) 48.4 / 1210 Height (inches / mm) 27.6 / 701 Depth (inches / mm) 3.8/96 Weight (pounds Power / 66 / 29.9 kg) AC100-240V, 50/60Hz requirement Resolution 852 Colour x 480 1024 (Dot) 32 MODEL 104°F (0 40°C) RT-50PX20/H / mm) 55.1 / 1400 Height (inches / mm) 32.3 / 821 Depth (inches / mm) 3.9/99 / 115 / 52.
