Please read this manual carefully before operating your set. Retain it for future reference. Record model number and serial number of the set. See the label attached on the bottom of the set and quote this information to your dealer when you require service.
LCD PROJECTOR Warning This is a class B product. interference, in which In case domestic environment this a the user may be required product may cause radio adequate measures. to take FCC NOTICE ? A Class B This digital device equipment has been device, pursuant tested and found to comply with the limits for to Part 15 of the FCC Rules. These limits are a Class B designed to digital provide reasonable protection against harmful interference in a residential installation.
CONTENTS INTRODUCTION Instructions ..................................................................4 Safety Names of parts .....................................................................12 INSTALLATION AND COMPOSITION Installation Instructions .........................................................18 Composition..........................................................................20 Turning on the Projector .......................................................
Safety Instructions Γ Please take note of the Γ Safety Instructions are safety NOTES Γ After reading in two forms given WARNING instructions to as prevent any potential accident The violation of this instruction may it in the keep projector. detailed below. The violation of this instruction may this manual, misuse of the or place that the cause user serious cause light injuries always can and injuries or contact damage even to the death. projector. easily.
INTRODUCIN Indoor Installation-NOTES Do not be - place the projector exposed to dust. This may cause a where it might When installing the projector on a table, place it near the edge. fire hazard ! This may - or Only - use the projector on a level and sta- ble surface. - adult and to the R operation. fall projector. suitable stand. use a Ensure jector.
Safety Instructions Outdoor Installation-NOTES In the If using a receiver (VCR, Digital Top Box), do not place an antenna in vicinity of power case Set of connecting a receiver (VCR, Digital Top Box), contact your service centre to erect an antenna as this lines. - Set work should be carried This may out cause an electric shock. - by skilled This may personnel. cause an electric shock.
INTRODUCIN Power-NOTES Never touch the power hand - This may cause an plug with a Hold the wet pull aged. you electric shock hazard ! - Prevent dust pins - or collecting on the power This may cause a This may Do not plug outlet. plug is when plug firmly unplugging. If the cord the cord may be damcause a fire hazard ! plug when the power cord or the damaged or the connecting part of the power outlet is loose.
Instructions Safety Using-WARNING Do not place anything containing liquid flowerpot, on top of the projector such as cup, cosmetics or candle. - This may cause a In of case projector shock impact damage to the unplug it from or switch it off and the mains outlet and contact your service center. fire hazard ! - This may fire cause a or an electric shock hazard ! R R Do not allow any objects to fall into the projector.
INTRODUCIN Using-WARNING Do not touch metal parts during or operation since the vents and Don't look directly onto the lens when the is in use. Eye damage may occur! after projector cover soon lamp will remain very hot! K R K Never touch the wall outlet when there is leakage of gas, open the windows and ventilate. -Itcancauseafireoraburnbyaspark. Using-NOTES Do not drop the projector or allow Do not impact shock. - place heavy objects on top of pro- jector.
Instructions Safety Using-NOTES Do not touch the lens of the projector. It is delicate and easily damaged. Do not use any sharp tools on the tor as this will damage the casing. R R Cleaning-WARNING Do not use water while cleaning In the the pro- This may projector cause or an damage event of smoke or a strange smell from the projector, switch it off unplug it from the jector - unlikely to the , wall outlet and contact your dealer or service centre. electric shock hazard.
INTRODUCIN Cleaning-NOTES Unplug before ers or - this product cleaning. Do an not use liquid clean- aerosol cleaners. This may the from the wall outlet cause Projector damage Contact the Service Center once a clean the internal parts of the - Accumulated dust to year to projector. can cause mechanical failure. or cause electric shock hazard ! R Others-WARNING Do not attempt to service the yourself.
Names of parts Main * Body The LCD projector is manufactured using high-precision technology. You may, however, see on the Projector tiny black points and/or bright points (red, blue, or green). This can be a normal result of the manufacturing process and does not always indicate a malfunction.
INTRODUCIN Rear Connecting Connecting Part A-RGB1 A-RGB2/D-RGB RS-232C Audio A-RGB1 A-RGB2/D-RGB RS-232C Audio K Rear remote control sensor Kensington Security System Connector (Refer to page 21) 13
Names of parts Control Control Panel , Selects Button menus and items in the MENU OK/ MENU Button Selects or closes menus. OK/Α Button menus. Checks saves VOL present mode and the change of functions. VOL VOLUME Button Adjusts volume level and functions of INPUT SELECT Button Switches to A-RGB1, A-RGB2, D-RGB, Video, S-Video, Component mode. INPUT SELECT PATTERN When pressing button, the focus POWER Button POWER 14 menus.
INTRODUCIN Remote Control Control POWER POWER Button KEYSTONE APC Button(Refer Button(Refer AUTO TRACKING to to Button(Refer to KEYSTONE INPUT SELECT APC STILL AUTO TRACKING BLANK INPUT SELECT Button p.49) p.53) STILL p.54) ARC Button(Refer to p.51) SWAP Button(Refer to p.47) ARC Button(Refer BLANK Button(Refer p.38, 47) to p.42) SUB INPUT SUB INPUT SWAP to Button(Refer to p.46) TWIN PICTURE TWIN PICTURE MENU MUTE MENU Button Button(Refer to p.
Names of parts Status Projector Status * Lamp Indicator, operation projector. Indicators indicator and temperature indicator at the top of the projector show the user the operating of the Lamp Indicator Temperature indicator Operation indicator R Red Initializing hardware after the main power applied. Standby. Green On operation.(Turn on the lamp) Orange(flashing) Projector lamp is cooling as power out(2 minutes) Orange Operation Lamp Indicator Off Power off.
INTRODUCIN Accessories POWER KEYSTONE INPUT SELECT APC STILL AUTO TRACKING BLANK ARC SUB INPUT SWAP TWIN PICTURE MENU VOL MUTE OK VIDEO COMPONENT ZOOM- ZOOM+ VOL A-RGB1 1.5V 1.5V Batteries 2 Remote Control Computer Audio Cable Audio/Video Cable Power Cord (size AAA) DVI Cable Cable SCART to RCA jack (option) ON 123456789 MAC Desktop Adaptor Optional * * Portable Bag Operating guide Extras Contact your dealer to purchase these items.
Installation Instructions * Don't place the projector in the following Provide proper ventilation for this conditions. It may cause malfunction or product damage. projector. The projector is equipped with ventilation holes(intake) on the bottom and ventilation holes(exhaust) on the front. do not block or place anything near these holes, or internal heat build-up may occur, causing picture degradation or damage to the projector.
Do not obstruct the slots and and create a openings of the This may projector. cause overheating fire hazard. R The LCD projector You may, however, is manufactured see tiny black continuously appear on the LCD ufacturing process and does not using high-precision technology. points and/or bright points (red, blue, or green) that projector Screen. This is a normal result of the manindicate a malfunction. To display DTV programmes, it is necessary to connect and connect it to the projector.
Composition Basic 1. 22. of of the Operation Operation Place the projector on a Place the projector the correct distance from the sturdy and horizontal surface with the PC determines the actual size of the 3. 3 or AV source. The distance between the screen. projector and the screen projector so that the lens is set at a right angle to the screen. If the projector is not set at a right angle, image will be crooked.
INSTALOD COMPSITN Using Security System System Using Kensington Security The has projector Security system a 'Kensington' Security System cable as Connector on the back panel. Connect the 'Kensington' below. For the detailed installation and use of the Kensington Security System, refer to the user's guide Kensington Security System set. And for further information, contact http://www.kensington.
Turning 1 Connect power cord 2 Remove the lens 3 on the Projector correctly. cover of the projector. Press the POWER button on the remote control of the lamp.) or top cover.(Green operation indicator flashes during cooling It will take about 1 minute to warm An display the picture after power on because the projector lamp has to up. image Select the Leave the will appear after the operation indicator light up(Green). source mode with the INPUT SELECT button.
Turning 1 off the Press the POWER button Projector on the top cover or remote control. on the top cover or remote control INSTALOD COMPSITN Power Off? Please Press 2 3 Key Again. Press the POWER button If the operation indicator LED is operation indicator LED until the If the or on to cut off the power. orange and blinking, do not disconnect the mains is lit up constantly (orange). indicator LED is orange and the remote control will not operate.
Operating the Projector Focus and Position of of the Screen Screen When an image appears on Image the screen, check if it is in focus and fits well to the screen. R Zoom To To ring Focus ring adjust the focus of the image, rotate the focus ring which is the outer ring on the lens. adjust the size of the image, rotate the zoom ring which is the inner ring on the lens. To raise or by pushing lower the image on the screen, adjuster button as below.
Selecting 1 mode INSTALOD COMPSITN Press the INPUT SELECT button. select Φ 2 source A-RGB1 OK Γ Each press of the VOLUME (Φ, Γ) button changes the display as below.
Connecting to a * You can a * You can use * projector to computer of VGA, SVGA, XGA and SXGA output. ARC function for the RGB signals of the Aspect Ration 4:3. (For HD wide input signals, you cannot ARC function.) Fundamentally, HD use * connect the Desktop PC wide Refer to page 63 for the input signal is not included in the Spec, so the set may supported pc graphic card displays of the projector. not support HD signal perfectly.
Connecting to a Notebook PC CONETI a A-RGB2/D-RGB RS-232C Audio K b < a. How to connect > Connect computer cable to A-RGB1 of the * If you set your computer, such as a notebook projector. type IBM PC/AT compatible, to output the signal to both the display of your computer and the external monitor, the picture of the external monitor may not appear properly. In such cases, set the output mode of your computer to output the signal only to the external monitor.
Connecting * You must use the Macintosh Desktop PC to a Macintosh desktop adaptor to connect the projector to a Macintosh PC. a A-RGB2/D-RGB RS-232C Audio K ON b 123456789 c d < How to connect a. b. > Connect computer cable to A-RGB1 of the Set the adjusting you want to use projector. number and letter of the Macintosh and connect the adaptor c. Connect the computer cable to the Macintosh d.
How to use use the Macintosh Adjusting desktop desktop adaptor letter CONETI ON 123456789 Adjusting a. How to use set 1 Usually adjusting the b. number Notes for 6 to OFF status and 7 ~ 9 to ON status of the ~ adjusting numbers. And select (Refer to page 30.) letter which is correct to the Macintosh and the monitor. Connecting to the Macintosh PowerBook If you get problems when connecting it to the status and restart the Macintosh PowerBook.
Connecting to a Macintosh Desktop PC of MAC desktop with type of MAC and output Adjusting letters of desktop adaptor in accordance with type of output spec. spec. output 12￥RGB 13￥x14￥RGB 15￥Portrait VGA SVGA SVGA 16￥Color 19￥Color 19￥Color 2Page Mono 21￥Color NTSC PAL resolution 512x384 640x480 640x870 640x480 800x600 800x600 832x624 1024x768 1024x768 1150x870 1152x870 NTSC PAL horizontal frequency(KHz) vertical frequency(Hz) 24.5 35 68.8 31 35 50 60 68.7 68.7 15.
to a Macintosh PowerBook Connecting a CONETI A-RGB2/D-RGB RS-232C Audio K ON b 123456789 c d < How to connect > a. Connect computer cable to A-RGB1 of the b. Set the adjusting projector. number and letter of the Macintosh you want to use and connect the adaptor c. Connect the computer cable to the Macintosh d. Connect the audio cable of PC (LINE desktop adaptor in accordance (Refer to page 29 30) to the Macintosh. with the resolution ~ desktop adaptor.
to a wireless transmitter Connecting ? ? ? When the wireless transmitter with external connecting connecting ports (Video - yellow, Audio(L) - equipments, white, Audio(R) -red). If you have a mono VCR, connect the audio cable from the VCR to the AV AV transmitter. See the wireless transmitter-receiver (option) match the colors of operating guide input of the wireless for installation and connection etc.
to a wireless receiver Connecting ? When connecting the wireless receiver with external equipment, jacks: Video-yellow, Left Audio-white), Right Audio-Red. (option) match the colors of connecting a CH4 CH3 CH2 CH1 AV INPUT 12V DC INPUT c b POWER SELECT INPUT VOL PATTERN MENU VOL OK/ S-Video Video Audio DC 12V OUT Component (DVD/DTV) AC Y
to a Video Source Connecting * You can connect a VTR, a camcorder, a LDP or any other compatible POWER video image source to the projector. INPUT SELECT VOL MENU PATTERN VOL S-Video Video Audio DC 12V OUT Component (DVD/DTV) Y PB OK/ PR AC IN R a S VIDEO AUDIO VO OUT IN b a. Connect the AV input jacks of the projector to the output jacks of the A/V source with A/V cables.
Connecting * The to a DVD output jacks (Y, PB, PR) of the DVD might be labelled as Y, Pb, Pr / Y, B-Y, R-Y / Y, Cb, Cr according to the equipment. POWER CONETI INPUT SELECT VOL MENU PATTERN VOL S-Video Video Audio DC 12V OUT Component (DVD/DTV) OK/ AC IN b R a (R) AUDIO (L) > Component (DVD/DTV) ports (Y, PB, PR) of the projector to the Video output ports (Y, PB, of the DVD. b. Connect the Audio port of the c.
to a D-TV Connecting * * * Set-Top Box To receive D-TV programmes, it is necessary to purchase a D-TV receiver (Set-Top Box) and connect it to the projector. Please refer to the owner's manual of the D-TV Set-Top Box for the connection between LCD projector and D-TV Set-Top Box. Use a D-TV receiver with DTV 720p/1080i mode.
Function * If there is * This checking input signal present, the Menu will not operating guide explains operation of A-RGB1 no 1 Press the MENU button to 2 Press the Δ, Ε button to select Each press will display cycle through a menu on the be displayed on mainly. the screen. mode screen. a menu. the different menus as shown below.
Using Still 1 function Press the STILL button. * You can freeze the input image. 2 38 To exit Pause, press any button * The STILL function would release
Selecting language 1 Press the MENU button and then use Δ / Ε button to select the English Language ARC Flip Flip 16:9 Horizontal Vertical Menu 2 3 Press the OK (Α) button and then Press the VOLUME (Φ, Γ) use menu. exit move OK Δ / Ε button to select button to select the language On-Screen-Display(OSD) is marked in the selected language menu display, press the MENU button. [Language] you want to from this item. SPECIAL FUNCTIOS use. point.
Checking lamp 1 Press the MENU button and then use V H time Δ / Ε button to select the menu. 0 Keystone Keystone 0 Zoom Blank Blue Image Set ID 1 Lamp Time Menu exit 0Hr move The used lamp time is displayed. When projector lamp is reaching the end of its red and the 40 the life(over 1500 hours), Lamp" on screen. the lamp indicator will be turned projector display "Replace "Replace the Lamp" is displayed for 10 seconds from the first power on.
Manual Color * 1 You can adjust red, green, or Temperature Control blue to any color temperature you Press the MENU button and then use Δ / Ε button to select the Twin Picture Color Temp. Color Temp. Color Temp. Menu 2 Press the OK (Α) button and then use 0 G 0 B 0 move Twin Picture R 0 Color G 0 B 0 Use the VOLUME The adjustment To exit the (Φ, Γ) range of menu button to make prev. move SPECIAL FUNCTIOS color. adjust appropriate adjustments. [Color Temp.
Using * This function may be effective if you need to or 1 2 get attention of the audience during presentations, meetings briefings. Press the BLANK button. * The * You screen can turns off to choose the a background background color and sound also turns off. color. Refer to page 43. Press any button to cancel the blank function. * 42 Blank function On exiting the blank status sound is also restored.
Blank Selecting 1 color color Image Press the MENU button and then use V H Δ / Ε button to select the Keystone Keystone menu. 0 0 Zoom Blank Image Blue Set ID 1 Lamp Time Menu 2 3 Press the OK (Α) button and then Press the VOLUME Background To exit menu (Φ, Γ) color will be display, 0Hr exit OK move Δ / Ε button to select use [Blank Image] button to select the color you want to changed SPECIAL FUNCTIOS item. use.
Using Flip Flip * Horizontal Function This function 1 Horizontal / Vertical function reverses the Use this function when projected image horizontally. Press the MENU button and then use Δ / Ε button to select the button and then exit move English 16:9 Flip Horizontal Flip Vertical Menu 44 OK(Α) button to see OK Δ / Ε button to select use Language Press the menu. 16:9 ARC 3 image.
Vertical Flip Vertical * This function * When you the projected image vertically. projector upside down from the ceiling reverses hang horizontally. 1 Function the Press the MENU button and then use (Α) button and then use exit move OK(Α) button to see menu. OK Δ / Ε button to select [Flip Horizontal] item.
Twin Picture function How to use twin picture TWIN PICTURE Press the TWIN PICTURE button to select desired with Twin Picture1 Twin Picture 2 Twin Picture Twin Picture 1 Input can use this function select of the sub by using : Off the MENU button. Press the SUB INPUT button to select the select 46 Off picture SUB INPUT Φ : Twin Picture 2 Twin Picture You picture. A-RGB1 OK Γ input source of sub picture.
Changing the picture of main and sub Press the SWAP button in twin picture picture mode. SWAP Using STILL A-RGB2 Video Video A-RGB2 Still function in twin picture Press the STILL button in twin Main Still Off Sub Still Off exit You can picture mode. SPECIAL FUNCTIOS mode. select cancel this function directly by selecting [Off] in menu. The STILL function is cancelled when changing the input signal.
Adjusting * 1 display screen If the image size does not fit the screen in accordance with the input source, set the position of the image by selecting Horizontal / Vertical position.
function Using Keystone * * 1 Use this function when the is not at a right angle to the can't get the best projector angle of and the projection, image is a because it Press the KEYSTONE button. V Keystone 0 H Keystone 0 exit 2 screen trapezoid shape. Only use the Keystone function when you may cause a blazing fire of the screen. adjust Press the Δ / Ε button to select [V Keystone] or [H Keystone] item.
Using * 1 Zoom function This function works Press the ZOOM in RGB mode. only or - ZOOM + button. 0/20 ZOOM- 2 Press the ZOOM or - ZOOM+ ZOOM + button to adjust the zoom 15/20 ZOOM- 3 4 20/20 ZOOM+ Move to the position you want to Ε button. ZOOM- see the enlarged screen ZOOM+ by moving press the VOLUME Δ, Press the OK (Α) or * * * R ARC button to exit the zoom function. This function doesn't work in Video, S-Video, Component mode.
Using ARC * You can select 16:9 picture function format only with an HD mode. input (720p,1080i) Press the ARC button. 1 Each press of the button changes < ARC the display as below.
Adjusting 1 Video Press the MENU button and move < the Δ / Ε button up > < Twin menu.
APC (Auto (Auto Picture Control) Control) * Use APC to set the * This function will not work in RGB mode. 1 projector for the picture appearance. Press the APC button. APC 2 best ΦUserΓ Each press of the APC button changes the screen as shown below. VIDEO User Clear * You also Soft this function by using (Video/S-Video/Component mode) can use the MENU button.
Using Tracking function Auto Tracking Tracking Function * Auto Tracking This function Function you of getting the best video quality by automatically adjusting the difference synchronization of the image. Auto Tracking function works in Analog RGB(A-RGB1, A-RGB2) input only. 1 assures Press the AUTO TRACKING button. Auto * 2 of horizontal size and Image positioning and synchronization Adjust [Clock] or [Phase] in ter picture quality in accordance are automatically adjusted.
Clock Clock / Phase Function * Clock Function This function * adjusts the horizontal width of the projected image to get the image to fit on the screen size. Phase Function This function is for the detailed * It's available to 1 adjustment of the clock function. adjust [Clock], [Phase] in Analog RGB mode only.
External control device setup * Connect the RS-232C input jack to an external control device (such as a computer or an A/V control system) Projector's functions externally. When you connect a control(RS-232C) cable to this projector, use a control cable with a ferrite core attached. If you do not do this, this projector will not conform to mandatory CISPR22(EN55022) standards. and control the * SET ID ? 1 Use this function to specify projector Press the MENU button and then use V H ID number.
How to connect external control ? ? Connect the serial port of the PC to the RS-232C RS-232C cable is not supplied with the projector. A-RGB1 jack equipment on the projector back panel. A-RGB2/D-RGB RS-232C Audio K ? Use the RS232C cable to control the RXD 2 3 TXD 3 2 RXD GND 5 5 DTR 4 4 DTR DSR 6 6 DSR RTS 7 7 RTS CTS 8 8 CTS Male Female (-) (-) Baud Rate : Data 19200 Length : 8 Parity : none ?Stopbit:1bit ? Fig.1).
Command Reference List Command1 Command2-1 Command2-2 k 0 0 00~63 00, 01 k 0 1 00~63 00~05 00~05 01. Power Select 02. Input 03. Aspect SET ID Data(Hexa) Data(Hexa) Ratio k 0 2 00~63 04. Screen Mute k 0 3 00~63 00, 01 05. Sub k 0 4 00~63 00~05 06. Contrast k 3 0 00~63 00~64 07. k 3 1 00~63 00~64 08. Color k 3 2 00~63 00~64 09. Tint k 3 3 00~63 00~64 10. k 3 4 00~63 00~64 11. Color R k 3 6 00~63 00~64 12.
01. Power (Command2-1:0, Command2-2:0) To control Power On/Off of the 03. To Projector.
9. Tint 06. Contrast To adjust (Command2-1:3, Command2-2:0) screen To (Command2-1:3, Command2-2:3) adjust Data [k][3][0][][SetID][ ][Data][Cr] * * * * Min:00~Max:64 Refer to 'Real data Always screen tint. [k][3][3][ ][SetID][ ][Data][Cr] Transmission Data the Transmission contrast. mapping That is, marks with two-place Hexadecimal writing and read data is also marked with Hexadecimal value. mapping2'. marks data value with Hexadecimal.
11. Color R Adjustment (Command2-1:3, Command2-2:6) To adjust red in color 14. Color Temp. R (Command2-1:3, Command2-2:9) Adjust temperature. Transmission Data * Data Min:00~Max:64 Refer to 'Real data Always temperature R of LCD part. [k][3][9][ ][SetID][ ][Data][Cr] [k][3][6][][SetID][][Data][Cr] * the color Transmission mapping * 1'. * marks data value with Hexadecimal. Min:00~Max:64 Refer to 'Real data mapping 1'. marks data value with Hexadecimal.
17. Twin Picture Mode Select 20. OSD Lock mode (Command2-1:4, Command2-2:1) To control the twin (Command2-1:9, Command2-2:0) This function picture. Transmission on [k][4][1][][SetID][ ][Data][Cr] Data 00:FULL 01:TWIN1 00:FULL 01:TWIN1 02:TWIN2 Keypad that Keypad and only Power button works with "OSD Lock On".
* The projector displays the best image quality at a resolution of 1280x720 pixels. display other resolution images, the projector compresses or expands it to 1280x720. The following table lists the display formats supported by the projector. To 640X350 70.090Hz 31.468kHz 640X350 85.080Hz 37.861kHz 640X400 70.090Hz 31.468kHz 640X400 85.080Hz 37.861kHz 720X400 70.082Hz 31.469kHz 720X400 85.039Hz 37.927kHz 640X480 59.940Hz 31.469kHz 640X480 66.667Hz 35.00kHz 640X480 72.800Hz 37.
* The needs little maintenance. You should projector the on screen. keep the lens clean because any dirt You will also need to clean the air filter attached at the bottom of the because a clogged air filter prevents proper ventilation that is necessary overheating. If any parts need to be replaced, contact your dealer. jector, always turn the power off and unplug the projector first.
Specifications MODEL LCD RL-JA20 size panel 0.87 inches resolution screen 1280(Horizontal) size x 720(Vertical)pixel 1.01~5.08m(40~200 inches) remote control distance 12m speaker system 3W horizontal / vertical ratio 16:9(horizontal:vertical) ratio 1:1.3 compatibility NTSC/PAL/SECAM/NTSC4.43/PAL-M/PAL-N zoom Video Power AC 100 height 240V~50/60Hz 294.1mm(including front foot) breadth 359.7mm length 115.5mm(including lens) weight 4.
P/NO : 3828VA0360B a (373-026H)
