Owner’s manual Please read this manual carefully before operating your device. MODEL: PC389P / PC389S ENGLISH You can print easily the photo via Bluetooth® The actual device may differ from the image.
Safety information CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK) NO USERSERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
CAUTION concerning the Power Cord The Power Plug is the disconnecting device. In case of an emergency, the Power Plug must remain readily accessible. Check the specification page of this owner’s manual to be certain of the current requirements. Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire.
WARNING: yy The flash may turn on in dark places. -- Do not use a flash too close to a person’s eyes. It may temporarily affect your eyesight. Be especially careful when taking photos of infants and young children. -- Do not take a photo towards a person driving a bicycle or car, or riding a horse because the flash may distract the operator. It may cause traffic accidents.
CAUTION: yy The apparatus should not be exposed to water (dripping or splashing) and objects filled with liquids, such as vases, shouldn’t be placed on the apparatus. yy Place the product on a sturdy, level surface. yy Minimum distance around the apparatus for sufficient ventilation, no less than 5 cm. (1.97 inches) yy Do not wet your Pocket Photo. Do not drop or shock your Pocket Photo. Also, do not put it in a place where sand is likely to get in.
,,Note Device operating temperature When operating in cold weather, the device may not print. Bring it inside from the cold and give about 10 minutes to adjust to the specified operating temperature (5 °C - 35 °C (41 °F - 95 °F)). Then try printing again. (For the appropriate use, it is recommended not to operate it outdoors in winter.) >>Caution CAUTION when using this product in environments of low humidity yy It may cause static electricity in environments of low humidity.
Contents Safety information . . . . . . . . . . . . . . . . . . . . . . . 2 STEP 1 Getting Started . . . . . . . . . . . . . . . . . . 8 Supplied items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . 8 STEP 2 Inserting Photo Cartridge . . . . . . . . . 9 About photo cartridge . . . . . . . . . . . . . . . . . . . . 11 STEP 3 Power On / Off . . . . . . . . . . . . .
STEP 1 Getting Started Product Overview Lens cover switch USB port (Type C) for recharging Supplied items *Reset hole LED indicator Flash Shutter LG Pocket Photo Printer (Power) button Simple manual (Reprint) button Paper exit slot Lens View finder *Reset hole: If you need to reset, press in the hole. USB cable (Type C) Strap yy Depending on the model or region, supplied items may differ. (ex. USB cable, strap etc.
STEP 2 Inserting Photo Insertion part of Photo cartridge Cartridge Strap hole 1. Slide the cover button sideways to open the bottom cover. Cover button 2. Unpack the photo cartridge you bought.
As shown in the following picture, lightly knock the photo cartridge in the direction of the arrow 2 or 3 times to align the paper to the back and put it in the Pocket Photo. 3. Insert the photo cartridge with the color ribbon facing forward as shown in the following image and close the cover. Photo Papers with White side up, Black side down. 10 4. Press the cover to close it completely.
Note on Photo Cartrigde yy Do not touch the color ribbon and the photo paper when inserting the cartridge. yy Do not touch the inside of the Insertion part of Photo cartridge (print head). There is a risk of burns. yy When opening the bottom cover, your hand or finger may get caught in the paper exit slot. yy If there is foreign substance on the inside of the Insertion part of Photo cartridge (print head), wipe it off with a cotton bud or a soft cloth.
Note on Photo cartridge Use exclusive Cartridge for LG Pocket Photo. yy Using photo cartridge from other company may result in malfunction, paper jam or low quality. yy Do not damage or bend the cartridge. yy Do not expose to direct sunlight or moisture. Do not allow the Pocket Photo to overheat. yy Do not disassemble or modify the photo cartridge. yy Using a soiled cartridge may result in malfunction. yy Once unpacked, the cartridge may begin to curl up or discolor after a period of time.
STEP 3 Power On / Off >>Caution Moving a Pocket Photo from a cold place to a warm place can cause dew on the inside / outside and print quality may deteriorate. Allow the dew to dry sufficiently before using the device. ,,Note yy When turning the device on, LED indicator flashes for 3 seconds, then printing is available. yy For more information, see “About LED indicator”. Press (power) button for 2 seconds to turn on or off.
STEP 4 Checking battery status When you disconnect the Pocket Photo from the charging cable, you can check the battery charge status via the LED indicators . If the power of the unit is turned on, you can check the charging status by pressing 1 (Power) button. The LED indicators will change depending on the 인쇄 준비battery charging status.
>>Caution Battery charging time: 2.5 hours , Charging time may vary depending on the type of adapter and charging environment. Checking the charging status with LED indicators front of Pocket Photo. : Power-off : Charging : Full charge yy yy Handle with care during charging to prevent electric shock. on yy Do not place near heating appliance. yy Do not disassemble or deform. yy Do not “shock” the Pocket Photo. yy 0 % : Blinks quickly and turns off. yy Avoid too high or low temperature or humidity.
,,Note yy You can connect the device to PC using a Smart phone USB cable (Type C), but charging time can be longer. yy The operating time on battery may vary depending on the battery status, operational status and environment conditions. yy When the battery is discharged, printing is available after charging it for more than 10 minutes. (Fully charge to print in a row) 16 STEP 5 Installing App Installing App for Android phone From Play Store (Android market) Search for “LG Pocket Photo”.
App Setting Set the options in [ Mode]. Bluetooth® Setting] / [Print Connection yy Bluetooth: When you turn on Bluetooth in the Pocket Photo app, the Bluetooth on your Android phone turns on. yy Shake & Print: When you turn on Shake & Print mode, select the desired photo from the main screen of the Pocket Photo app and then shake your smartphone to print. See “Help” for details For more information about the App, touch [Help] on the [ Setting].
Installing App for iPhone From App Store Search for “LG Pocket Photo”. Using QR code You can enter the App Store by scanning the QR code on the product box. Setting Bluetooth of iPhone 1. On your iPhone’s home screen, touch [Settings]. 2. Touch “Bluetooth” and touch the slider to turn Bluetooth [On]. 3. To connect your Pocket Photo device to the iPhone, turn on your device and make sure it is discoverable mode. 4. When you find the device, touch the model name of Pocket Photo on the screen.
See “Help” for details For more information about the App, touch [Help] on the [ Setting]. STEP 6 Printing Photo Printing using Android phone Bluetooth® Printing using Bluetooth ( ) Bluetooth® Preparation: Turn the device on, and start printing with the LED indicator turning on. 1. Run LG Pocket Photo App on Android phone. 2. Select a photo to print, and touch [ Pocket Photo App. ] (Print) on 3. [Device Connection] window appears.
>>Caution yy Check the power of the Pocket Photo, when your device can not search for Bluetooth device. yy A photo file of less than 10 MB can be printed in case of Android. yy Setting screen may differ depending on the phone manufacturer. yy When connecting to the other company’s smartphone, some functions may be limited depending on conditions. 6. If you want to print a photo you took again, press [ ] (Reprint) button on the top of Pocket Photo.
Setting Pocket Photo App of Android phone 1. Run LG Pocket Photo App on Android phone. 2. Go to [ Setting]. (To check [Device information], set the smartphone Bluetooth to [On]) in the [Print Connection Mode]). 3. Touch [Device Information]. You can check device condition, battery status, total printed photos, MAC address and firmware version. You can change setting of printing method and Automatic device power off in [Print setting]. yy Printing Method: You can set the printing method of photo.
,,Note yy If you change the time of Automatic Device Power Off, the maximum number of prints can be changed due to battery consumption. yy It is recommended to keep the default settings of the device. Printing using iPhone Printing using Bluetooth ( ) Bluetooth® Preparation: Turn the device on, and start printing with the LED indicator turning on. 1. Run LG Pocket Photo App on iPhone. 2. Select a photo to print, and touch [ Pocket Photo App. ] (Print) on 3. Touch [Print the photo] on the print window.
Setting iPhone Pocket Photo App You can check device condition, battery status, total printed photos, MAC address and firmware version. 1. Run LG Pocket Photo App on iPhone. (To check [Device information], set the iPhone Bluetooth to [On]). 2. You can check the device information by touching [Device Information] on the [ Setting] 4. If you want to print a photo you took again, press [ ] (Reprint) button on the top of Pocket Photo.
You can change the settings for the printing method and Automatic device power off in [Print setting]. ,,Note yy Printing Method: You can set the printing method of photo. yy If you change the time of Automatic Device Power Off, the maximum number of prints can be changed due to battery consumption. -- Paper Full: Prints without white space. (The edge of the image may be cut off.) yy It is recommended to keep the default settings of the device. -- Image Full: Prints an image as a whole.
Using the edit mode You can use the editing functions of the Pocket Photo app to decorate your pictures with text, brushes (drawing tools), frames, and more. You can also calibrate your photos through various filter modes. ,,Note If you want to change the text of a photo in the editing function, the font applied is the same as when you change the font of your smartphone. (The Pocket Photo app does not support font changes.
yy The Bluetooth searching and transferring may fail depending on its environment. Check the Bluetooth condition on your phone and try again. yy If pairing multiple smartphones, re-pairing may occur. yy If you print continuously, the print time may be delayed. (takes about 1-2 minutes) -- Print time may vary depending on the surrounding environment. yy Only the last photo taken with the camera or printed with the app can be reprinted. When the power is turned off or reset, the reprint function is disabled.
yy The printing quality may differ depending on the original image (When too dark or dim). Use the image after correcting it using Pocket Photo App. Checking where to buy paper 1. To check where to buy paper, go to [ setting]. 2. After touching [Where to buy paper], select a country. yy During the print cycle, the photo paper will repeatedly come out and go back in about 5 times through the ejection port.
Updating the device You can update the device by pairing smart phone to the latest software to enhance the products operation and /or add new features. ,,Note yy During the device update procedure, do not turn off the power or press Reset button. 1. Connect the device and smart phone via Bluetooth. yy This device cannot be updated to previous version. 2. Run the Pocket Photo App and then, touch [Device information] on the [ setting].
STEP 7 Taking photos and instant printing 3. Hold the Pocket Photo, confirm the desired composition of the final image by using view finder. (It is recommended that you use the viewfinder eyepiece within 10 mm. (0.39 inches)) Taking photos 1. Press (power) button for 2 seconds to turn on. 2. Open the lens cover by lowering the lens cover switch. Optimal distance for taking photo is approximately between 0.5 m and 1.5m. (1.64 ft ~ 4.92 ft) The subject may shake when taking pictures.
(Reprint) button Shutter Note on taking photo yy Be careful not to touch the lens surface when you take the photo. yy Use a blower, cotton bud or soft cloth to remove dirt on the lens or view finder. View finder 4. To take a photo, press Shutter button for 2 seconds. Then the Pocket Photo prints a photo you took with a shutter sound. ※ When you are in a dark area, the flash may turn on when taking photos. 5.
,,Note yy Only the last photo shot with the camera or the last printed image with the app can be reprinted. You can not use reprint function when the power is turned off or reset. yy During the print cycle, the photo paper will repeatedly come out and go back in about 5 times through the ejection port. Please wait and do not pull out the photo by hand until it is finally released, (printing complete). yy The flash has an effective range of between 0.7 m and 1.8 m. (2.3 ft ~ 5.
Printing black-and-white photo If you switch your Pocket Photo to black-and-white shooting mode, you can print the photo in black and white when taking photos. 1. Press (power) button to turn on. 2. Close the lens cover by raising the lens cover switch. 32 >>Caution yy You can not switch to black-and-white shooting mode, if you do not have a photo cartridge in Pocket Photo. And you can not switch to black-and-white shooting mode while printing.
3. Press Shutter button for 5 seconds. The LED will light up in white and switch to black-and-white shooting mode. ,,Note yy When printing via the Pocket Photo app, the camera prints in color even if it is set to blackand-white shooting mode. yy After switching to black-and-white shooting mode, Black-and-white shooting mode is still operated even when the Pocket Photo is turned off and on. 4. Open the lens cover by lowering the lens cover switch. 5.
Using a strap Wind (Attach) the strap as shown in the below image to prevent dropping the Pocket Photo when you are carrying it or when taking a photo. Checking Label In case there are more than a LG Pocket Photo device, check MAC address on the product label to choose one you want to use. ,,Note yy Wind the strap around your wrist, never wrap around your neck. yy Use caution not to block paper exit slot with the strap. yy It is recommended to use the supplied strap only. 34 1.
About LED Indicator The LED indicators shows the device condition. Product label. : LED On 프린트 대기/ 켜짐 (흰색) : LED Blinks : LED Off 전원을 켤때/ 2. You can find the product label. 깜박임 Section (흰색) 전원 꺼짐 LED color Condition off 프린트 대기/ 켜짐 (흰색) 충전 중 Description To print, turn on the device. Power 전원을 켤때/ 깜박임 (흰색) 충전 완료 Turning on/ Blinks Blinks until ready after turning on.
인쇄 중 Section 프린트 켜짐 (흰색) 프린트 켜짐 (흰색) 전원을 깜박임 프린트 (흰색) 켜짐 전원을 (흰색) 깜박임 (흰색) 대기/ LED color Condition Description Waiting/ On Waits for printing. Device turns itself off, if it is left unused for a while. 대기/ 켤때/ 대기/ 켤때/ 전원 꺼짐 전원을 켤때/ 깜박임 전원 꺼짐 (흰색) Power 충전 중 전원 꺼짐 충전 중 충전 완료 충전 중 충전 완료 충전 완료 Charging Full charge Battery is charging Battery is fully charged.
용지 부족 커버 열림 용지 걸림 에러 Section LED color Condition 인쇄 준비 업데이트 프로그램 읽는 중 인쇄 중 Printing/On 배터리 30% 이상(흰색)/ 5장 이상 출력 가능 배터리 30% 미만 Normal 프린트 불가 operation (3회 깜박임) 배터리 부족 =>확인 후 삭제 Continuous printing during charging / Blinks (Red Green) Description Printing (While continuous printing, battery temperature is overheated. Wait for a while.) While continuous printing, the temperature inside the Pocket Photo will rise.
Section LED color Condition No paper, Paper jam/ Blinks 용지 부족 커버 열림 용지 걸림 에러 Error 리프린트할 출력물 없음 (3회) 리프린트할 출력물 없음 (3회) 고온/저온 (사용자 해결 불가) 업데이트 38 Description Insert the photo cartridge then try again. Turn down the lens cover Closed the lens switch when cover/ Blinks you take a photo. You will need to print at least Reprint button one photo is disabled./ after turning Blinks on the Pocket Photo. Specifications Paper size 63 mm x 94 mm (2.5 inches x 3.
Paper Feeding Out Automatic Flash Auto (White LED) LED indicator Image file type/ size PNG, JPEG (Baseline) / less than 10 MB (Progressive JPEG is not supported.) Power / Waiting / Bluetooth transmitting / Charging / Error / Condition of printer/ Update / Black-and-White shooting mode setting Communication Bluetooth 4.
yy Your phone may be incompatible with the device depending on its manufacturer, environment or (Android or iOS) operating system. yy Design and specifications are subject to change without prior notice. yy All other product and brand names are trademarks or registered trademarks of their respective owners. 40 Troubleshooting Symptom No power Bluetooth paring does not work well. Cause / Solution The battery is discharged. Be sure the device is connected to charger or PC properly when charging.
The paper is jammed before printing. The paper is jammed during printing. 1. Turn the device off and on again then the paper will be ejected automatically. 2. If above solution does not work, open the cover. Then insert the photo cartridge again. At first remove the photo cartridge, and then gently pull the remaining photo paper out of the Insertion part of Photo cartridge. At this time, be careful not to touch the inside of the Insertion part of Photo cartridge. The printed photo has lines.
White space When print mode is set to appears at the edge [Image Full] , white space may of the paper. appear if the aspect ratio of the paper and your image is not the same. When print mode is set to [Paper Full] , the edge of the image can be cut off or white space at the edge of the paper may appear. Quality of printed In case you magnify an image photo is too low. using [ ] menu in the App, the quality of the printed photo may be reduced. Turn off the Pocket Photo and insert the new photo cartridge.
The printed photo is out of focus by taking photo. The picture is blurred. The photo you printed is too dark by taking photo. Take a photo with a distance of at least 0.5 m (1.64 ft) between you and your subject. Clean the lens. When you take a photo, press the shutter button slowly after holding the Pocket Photo with both hands. Also hold your elbows close to your body. Do not press onto or fold the photo paper. Do not block the paper exit slot with your finger.
Paper Jam Solution Paper Jam Solution Do not pull the paper out. Turn the device off and on again, the paper will be ejected automatically. yy If there are foreign substance or dust on the inside of the Insertion part of Photo cartridge (print head), printed photo may has lines. In that case, wipe the foreign substance off using the head of a cotton bud or a soft cloth and then try again. Refer to “Troubleshooting” to clean the part. 1.
2. Gently pull the remaining photo paper out of the Insertion part of Photo cartridge.
