LED TV LV30** AAA X4 X2 (M4 x L16) (M4 x L16) 32LV30** 43LV30** www.lg.
1 2-A 2-B 32LV30** L R 3 43LV30** L R
ANTENNA/ CABLE IN HDMI IN USB IN H/P OUT MCIA CARD SLOT Satellite IN
PCMCIA CARD SLOT COMPONENT IN VIDEO/Y PB PR L/MONO AUDIO R AV IN VIDEO/Y PB PR L/MONO AUDIO R
COMPONENT IN VIDEO/Y PB VIDEO AV IN PR L/MONO AUDIO R AUDIO VIDEO/Y PB PR L/MONO AUDIO R VIDEO L/MONO AUDIO R
HDMI-DVI IN RGB IN RGB IN HDMI IN VIDEO/Y PB PR L/MONO AUDIO R AUDIO OUT VIDEO/Y PB DVI OUT PR L/MONO AUDIO R AUDIO OUT RGB OUT
1 2 3 4
0 1 2 A E D B G F A C B C D E F F G 32LV300C-ZB 732 478 181.1 438 77.8 5.1 5.0 32LV300C-ZA 728 475 181.1 436 77.8 5.0 4.9 43LV300C-ZA 970 624 220.4 569 77.8 8.4 8.
OWNER’S MANUAL Safety and Reference LED TV* * LG LED TV applies LCD screen with LED backlights. Please read this manual carefully before operating your set and retain it for future reference. www.lg.com Copyright © 2017 LG Electronics Inc. All Rights Reserved.
Warning! Safety instructions ENGLISH CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL. This symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
• Make sure the power cord is connected securely to the power plug on the TV. • Install the product where no radio wave occurs. • There should be enough distance between an outside antenna and power lines to keep the former from touching the latter even when the antenna falls. This may cause an electric shock. • Do not install the product on places such as unstable shelves or inclined surfaces. Also avoid places where there is vibration or where the product cannot be fully supported.
ENGLISH • Please follow the installation instructions below to prevent the product from overheating. -- The distance between the product and the wall should be more than 10 cm. -- Do not install the product in a place with no ventilation (e.g., on a bookshelf or in a cupboard). -- Do not install the product on a carpet or cushion. -- Make sure the air vent is not blocked by a tablecloth or curtain. This may result in fire.
Lifting and moving the TV Please note the following advice to prevent the TV from being scratched or damaged and for safe transportation regardless of its type and size. ENGLISH • Use a certified cable with the HDMI logo attached. • If you do not use a certified HDMI cable, the screen may not display or a connection error may occur.
Using the button (Depending on model) ENGLISH You can simply operate the TV functions, using the button. Mounting on a table 1 Lift and tilt the TV into its upright position on a table. • Leave a 10 cm (minimum) space from the wall for proper ventilation. 10 cm 10 cm 10 cm 10 cm 10 cm 2 Connect the power cord to a wall outlet. • Do not place the TV near or on sources of heat, as this may result in fire or other damage. • Do not apply foreign substances (oils, lubricants, etc.
Securing the TV to a wall Mounting on a wall (This feature is not available for all models.) 10 cm 10 cm 10 cm • Make sure that children do not climb on or hang on the TV. • Use a platform or cabinet that is strong and large enough to support the TV securely. • Brackets, bolts and ropes are not provided. You can obtain additional accessories from your local dealer. ENGLISH 1 Insert and tighten the eye-bolts, or TV brackets and bolts on the back of the TV.
• Remove the stand before installing the TV on a wall mount by performing the stand attachment in reverse. ENGLISH • When installing the wall mounting bracket, it is recommended to cover the stand hole using tape, in order to prevent the influx of dust and insects. (Depending on model) How to use Dual Lock™ (Only when the item of the following form is provided) (This feature is not available for all models.) Fix the set-top box to the TV and use it when you want to.
Connections (notifications) Satellite dish connection (Only satellite models) Connect the TV to a satellite dish to a satellite socket with a satellite RF cable (75 Ω). Available external devices are: HD receivers, DVD players, VCRs, audio systems, USB storage devices, PC, gaming devices, and other external devices. (Depending on model) • The external device connection may differ from the model. • Connect external devices to the TV regardless of the order of the TV port.
Remote control Network setup Wired network connection ENGLISH (Depending on model) This TV can be connected to a Pro:Centric server via the LAN port. After making the physical connection, the TV needs to be set up for network communication. Connect the LAN port of the Modem or Router from Pro:Centric server to the LAN port on the TV. (Some buttons and services may not be provided depending on models or regions.) The descriptions in this manual are based on the buttons on the remote control.
Licenses Supported licenses may differ by model. For more information about licenses, visit www.lg.com. ENGLISH (POWER) Turns the TV on or off. Selects Radio, TV and DTV programme. Recalls your preferred subtitle in digital mode. Audio descriptions function will be enabled. Resizes an image. (INPUT) Changes the input source. Number buttons Enters numbers. Accesses the saved programme list. Returns to the previously viewed programme. Adjusts the volume level. Accesses your favourite programme list.
Troubleshooting ENGLISH The software version can be updated for improvement in performance. Customer needs to ensure the compatibility of customer’s equipment with LGE software. If needed, please consult with LGE and upload revised software version according to the guidance provided by LGE. Cannot control the TV with the remote control. • Check the remote control sensor on the product and try again. • Check if there is any obstacle between the product and the remote control.
Specifications CI Module Size (W x H x D) 0 °C to 40 °C Operating Humidity Less than 80 % Storage Temperature -20 °C to 60 °C Storage Humidity Less than 85 % ENGLISH Environment condition 100.0 mm x 55.0 mm x 5.
HDMI/DVI-DTV supported mode ENGLISH Resolution Horizontal Frequency (kHz) Vertical Frequency (Hz) 640 x 480 31.46 31.50 59.94 60.00 720 x 480 31.469 31.50 59.94 60.00 720 x 576 31.250 1,280 x 720 1,920 x 1,080 640 x 350 720 x 400 640 x 480 800 x 600 1,024 x 768 1,152 x 864 1,360 x 768 1,280 x 1,024 (FHD only) 1,920 x 1,080 (FHD only) 14 Component ports on the TV Y PB PR Y PB PR Y B-Y R-Y 50.00 Y Cb Cr 37.50 45.00 44.96 50.00 60.00 59.94 Y Pb Pr 28.125 33.75 33.72 56.
Supported video formats • File type: MP3 [Bit rate] 32 Kbps ~ 320 Kbps [Sample freq.] 16 kHz ~ 48 kHz [Support] MPEG-1, MPEG-2, Layer2, Layer3 • File Type: AAC [Bit rate] Free Format [Sample freq.] 8 kHz ~ 48 kHz [Support] ADIF, ADTS • File Type: M4A [Bit rate] Free Format [Sample freq.] 8 kHz ~ 48 kHz [Support] MPEG-4 • File Type: WAV [Bit rate] 64 kbps ~ 1.5 Mbps [Sample freq.] 8 kHz ~ 48 kHz [Support] LPCM [Bit depth] 8 bit / 16 bit / 24 bit • File Type: WMA [Bit rate] 128 Kbps ~ 320 Kbps [Sample freq.
Supported photo formats ENGLISH • Category: 2D (jpeg, jpg, jpe) [Available file type] SOF0: Baseline, SOF1: Extend Sequential, SOF2: Progressive [Photo size] Minimum: 64 (W) x 64 (H), Maximum (Normal Type): 15,360 (W) x 8,640 (H), Maximum (Progressive Type): 1,920 (W) x 1,440 (H) • Category: BMP [Photo size] Minimum: 64 (W) x 64 (H), Maximum: 9,600 (W) x 6,400 (H) • Category: PNG [Available file type] Interlace, Non-Interlace [Photo size] Minimum: 64 (W) x 64 (H), Maximum (Interlace): 1,200 (W) x 800 (H),
Record the model number and serial number of the TV. Refer to the label on the back cover and quote this information to your dealer when requiring any service.
IR CODES • This feature is not available for all models.
EXTERNAL CONTROL DEVICE SETUP Type of Connector: D-Sub 9-Pin Male 1 5 ENGLISH RS-232C Setup • Image shown may differ from your TV. Connect the RS-232C (serial port) input jack to an external control device (such as a computer or an A/V control system) to control the product’s functions externally. Connect the serial port of the control device to the RS-232C jack on the product back panel. • RS-232C connection cables are not supplied with the product.
RS-232C Configurations Command Reference List (Depending on model) 7-Wire Configurations (Standard RS-232C cable) RXD TXD GND DTR DSR RTS CTS PC 2 3 5 4 6 7 8 TV 3 2 5 6 4 8 7 D-Sub 9 D-Sub 9 TXD RXD GND DSR DTR CTS RTS 3-Wire Configurations (Not standard) RXD TXD GND DTR DSR RTS CTS PC 2 3 5 4 6 7 8 TV 3 2 5 6 4 7 8 D-Sub 9 D-Sub 9 TXD RXD GND DTR DSR RTS CTS COMMAND2 DATA (Hexadecimal) 01. Power 02. Aspect Ratio 03. Screen Mute 04. Volume Mute 05.
Transmission / Receiving Protocol (Depending on Model) ENGLISH Transmission [Command1][Command2][ ][Set ID][ ][Data][Cr] [Command 1]: First command to control the TV. (j, k, m or x) [Command 2]: Second command to control the TV. [Set ID]: You can adjust the set ID to choose desired monitor ID number in option menu. Adjustment range is 1 to 99. When selecting Set ID ‘0’, every connected set is controlled.
03. Screen Mute (Command: k d) ►To ► select screen mute on/off. 05. Volume Control (Command: k f) ►To ► adjust volume. You can also adjust volume with the volume buttons on remote control.
08. Colour (Command: k i) ►To ► adjust the screen Colour. You can also adjust colour in the PICTURE menu. ENGLISH Transmission [k][i][ ][Set ID][ ][Data][Cr] * Refer to “Real data mapping” 09. Tint (Command: k j) ►To ► adjust the screen tint. You can also adjust tint in the PICTURE menu. Transmission [k][j][ ][Set ID][ ][Data][Cr] * If you are not using the remote control, use this mode. When main power is on/off, external control lock is released.
15. Energy Saving (Command: j q) ►To ► reduce the power consumption of the TV. You can also adjust Energy Saving in PICTURE menu.
Channel data range Min: 00 Max: 270F (0 to 9,999) ENGLISH Ack [a][ ][Set ID][ ][OK/NG][Data][x] 19. Programme Add/Skip (Command: m b) ►To ► set skip status for the current Programme. Data Structure MSB LSB 0 01: Add 20. Key (Command: m c) ►To ► send IR remote key code. Transmission [m][c][ ][Set ID][ ][Data][Cr] 0 0 IR CODES 21.
* Real data mapping 00: Step 0 Step 10 (Set ID 10) F: 10: Step 15 (Set ID 15) Step 16 (Set ID 16) 64: Step 100 6E: Step 110 73: 74: Step 115 Step 116 CF: Step 199 FE: FF: Step 254 Step 255 ENGLISH A: 9