OWNER'S MANUAL Color Video Camera Please read this manual carefully before operating your set and retain it for future reference.
CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
• Caution: Danger of explosion if battery is incorrectly replaced. Replaced only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions. • Holes in metal, through which insulated wires pass, shall have smooth well rounded surfaces or shall be provided with brushings.
Disposal of your old appliance 1. When this crossed-out wheeled bin symbol is attached to a product it means the product is covered by the European Directive 2002/96/EC. 2. All electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities. 3. The correct disposal of your old appliance will help prevent potential negative consequences for the environment and human health.
Important Safety Instructions 1. Read these instructions. and the point where they exit from the apparatus. 2. Keep these instructions. 3. Heed all warnings. 11. Only use attachments/accessories specified by the manufacturer. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. 8.
Cautions for Safe Operation Power Supply LS521P-B1/LS521N-B1: use a cloth dampened with a small quantity of neutral detergent then wipe dry. • This camera must always be operated a AC 24 V or DC 12 V Certified/Listed, class 2 power supply only. LS521P-C: Avoid the use of volatile solvents such as thinners, alcohol, benzene and insecticides. They may damage the surface finish and/or impair the operation of the camera. This camera must always be operated a AC 230 V.
Contents Features.................................................................. 8 Camera Identification Settings.................................23 Exposure Settings..........................................................24 Part Names and Functions.................................... 9 Connections......................................................... 12 White Balance settings................................................27 Day/Night Setting......................................................
Features This Color Video Camera is designed for installation in an video surveillance system. This manual contains instructions on how to install and manage the Color Video Camera in your video surveillance system. Should you require any technical assistance, please contact authorized service center. • High resolution and high sensitivity with a 6 mm Super HAD CCD II. • 650 TV lines of horizontal resolution. • Day & Night function. • C/CS Mount. • Line Lock when using AC 24 V.
Part Names and Functions a b c d e f c Camera installation bracket The bracket can be fixed at the top or bottom of the camera. d Lens iris output connector (LENS) This 4- pin connector is used to send the Iris control signal and power supply to an auto-iris type lens. e Setup menu control buttons Use these buttons to set the menu options. f ALC Lens Setting Switch a Lens mount cap • DC: When you attach an Auto Iris lens requiring the DC control signal, please put this switch in the DC position.
Part Names and Functions g Power input terminal LS521N-B1 / LS521P-B1 g h i j Supplies AC 24 V or DC 12 V from an external power source. h GND i Power indicator Lights when the camera is powered. j Video output connector (BNC type) Supplies analog video signal (composite) to the connected device such as a DVR or monitor.
Part Names and Functions g Power input cable (AC 230 V) LS521P-C g h i h GND j i Power indicator Lights when the camera is powered. j Video output connector (BNC type) Supplies analog video signal (composite) to the connected device such as a DVR or monitor.
Connections Precautions • Be sure to switch off the unit before installation and connection. • A qualified service person, complying with all applicable codes, should perform all required hardware installation. • Do not expose the power and connection cable to moisture, which may cause damage to the unit.
Connections Connecting Display device 3. The video signal connection between the camera and the monitor. Note: Connect to the DC 12 V / AC 24 V UL Listed, Class 2 Power Supply only on the unit. Just make sure that the DC power tips are connected with (+) and (-) matched correctly. Mismatch can be the cause of failure or malfunction. Connecting Power Source LS521P-B1/LS521N-B1 Connect power, using the method listed below: 1. Remove the insulation on the power cable as illustrated. (a) 2.
Connections Mounting the Lens LS521P-C Insert the plug of the power cord into a wall outlet. The POWER indicator will light. 1. Remove the lens mount cap from the camera. 2. Install the auto-iris lens. 2-1. CS mount type lens Carefully align the lens mount with the camera opening, then turn the lens slowly to install it. 2-2.
Connections 2-2 2-1 lens iris output connector Pin layout for the lens iris output connector. 2-1 2-2 3. No. DC type lenses VIDEO type lenses Connect the lens plug to the lens iris output connector (LENS) on the side of the camera. 1 Damping - Vcc (+9 V) 2 Damping + Not used When using lenses from other makers, the plug shape may not correspond to the terminal on the camera.
Connections Concerning Auto-Iris Lenses Rewire the lens iris plug 1. Cut off the plug of the lens cable, cut off approximately 8 mm of the insulation, and then strip approximately 2 mm of the ends of the cable sheaths. 8mm 2mm DC type auto-iris lens A lens without driver circuit that operates only on a DC power source. In general, this type of lens is referred to as DC type coil lens. (Set the ALC Lens Setting Switch to the DC position.
Connections VIDEO type auto-iris lens A lens with amplifier circuit that operates on video signal and DC power source. In general, this type of lens is referred to as EE amplifier type lens. ALC and LEVEL volume level controls are available on the lens for iris adjustments. (Set the ALC Lens Setting Switch to the VIDEO position.
Connections Note: If using a camera mounting bracket, select a location that is strong enough to bear the full weight of the camera and the mounting bracket for long periods, and install the camera and mounting bracket securely. 3. Tighten the flange-back fixing screws. Note: The object may be out of focus when using a source of near-infrared light than using the visible light. Mounting the camera The mounting bracket can be secured on either the top or bottom of the camera.
Menu Operation OSD Menu control buttons BUTTON Description UP button Used to move upper direction on the menu screen. Use this button to select an item or adjust the parameters. DOWN button Used to move lower direction on the menu screen. Use this button to select an item or adjust the parameters. This camera utilizes an on-screen user MENU. To set items on the menu, use the following buttons. RIGHT button LEFT button Moves the cursor to the right. Used to increment the value selected in the menu.
Menu Operation OSD Menu Overview Main Menu The following table shows the list of menu items and options. You can adapt the camera to your requirements by setting up the respective items in these menus. Sub Menu Contents CAMERA ID - OFF, 1 to 255 BACKLIGHT OFF/BLC/HSBLC BRIGHTNESS 0 to 100 AGC OFF/LOW/MIDDLE/ HIGH SHUTTER X512, ... , x2, AUTO, OFF, A.FLK, 1/160, ...
Menu Operation Main Menu Sub Menu Contents ZONE NUMBER MOTION DET ON ZONE STATE ON/OFF HEIGHT 12 to 100 WIDTH 16 to 100 MOVE Y 6 to 94 MOVE X 8 to 92 SENSITIVITY 0 to 100 EXIT RET/TOP/END OFF 3D-DNR Main Menu AREA1 to AREA4 OFF - LOW - MIDDLE - HIGH - Sub Menu Contents OFF PRIVACY ON MASK NUMBER AREA1 to AREA8 DISPLAY ON/OFF COLOR GRAY, WHITE, BLACK HEIGHT 4 to 100 WIDTH 4 to 100 MOVE Y 2 to 98 MOVE X 2 to 98 EXIT RET/TOP/END 21
Menu Operation Main Menu Sub Menu Contents Main Menu OFF D-ZOOM D-EFFECT SPECIAL 22 ZOOM PAN TILT EXIT ON OFF/ V-FLIP/ MIRROR/ ROTATE SHARPNESS 0 to 68 STABILIZER OFF/ ON COLOR OFF/ ON SYNC INT / LL USER TITLE OFF/ ON LANGUAGE ENG/RUS (The supported language can be different depending on the model.
Menu Operation General Operation 1. • • Press [SET] button. The setup menu screen appears on the monitor. TOP: Return to the CAMERA SETTING menu screen. END: Exit the setup menu. Camera Identification Settings You can use the camera identification (CAMERA ID) to assign a number to the camera. 2. Use [UP] or [DOWN] button to select an option then press [SET] button. Submenu appears on the monitor. 3. Use [UP] or [DOWN] button to select a submenu option. 4.
Menu Operation Exposure Settings You can set the exposure options using the EXPOSURE menu. 1. Select [EXPOSURE] option on the [CAMERA SETTING] menu. 2. Use [LEFT] or [RIGHT] button to select a mode (ALCy ELC). 3. Press [SET] button and the EXPOSURE menu appears. BACKLIGHT setting Use BACKLIGHT option to view the object clearly in backlight conditions. 1. Select [BACKLIGHT] option. 2. Use [LEFT] or [RIGHT] button to select a mode then press [SET].
Menu Operation • HSBLC: Use for masking brightness of the specific area to view the subject more clearly. The HSBLC mode is automatically activated only in low luminance scene. AREA SETTING: Use [LEFT] or [RIGHT] button to select a area then use [UP] or [DOWN] button to select a ON or OFF. Press [SET] to exit the Area setting menu. > GRAY SCALE: Use [LEFT] or [RIGHT] button to select a gray scale. (GRAYyD.GRAYyBLACK). > USER SCALE: Use [LEFT] or [RIGHT] button to select a bright level.
Menu Operation AGC (Automatic Gain Control) setting SHUTTER (Shutter Speed) setting If the images are too dark, change the maximum [AGC] value to make the images brighter. Select the desired shutter speed for camera exposure. You can change the shutter speed to higher speed to capture fast-moving subjects, though the image becomes darker. 1. Select [AGC] option. 2. Use [LEFT] or [RIGHT] button to select a mode. (OFFy LOWyMIDDLEyHIGH) 26 1. Select [SHUTTER] option. 2.
Menu Operation SENS-UP setting Note: If pictures are not clear due to darkness, this SENS-UP operation would increase the sensitivity of picture. If you set to one of the SHUTTER options except AUTO on the [SHUTTER] menu or [AGC] to [OFF], the [SENS-UP] setting is not available and [---] mark is displayed. White Balance settings 1. Use [UP] or [DOWN] button to select [SENS-UP] option. 2. Use [LEFT] or [RIGHT] button to select mode.
Menu Operation 1. Select [WHITE BAL] option. 2. Use [LEFT] or [RIGHT] button to select a mode then press [SET]. • ATW (Auto-Tracing White Balance): The color temperature range for the proper white balance is approximately 1 700 K to 11 000 K. Proper white balance may not be obtained under the following conditions: > > > • AWCbPUSH: If you select the AWCbPUSH mode, you will be able to set up the White Balance automatically using [SET] button. • MANUAL: You can set the white balance options manually.
Menu Operation 1. Select [DAY/NIGHT] option. 2. Use [LEFT] or [RIGHT] button to select mode for day/ night function. • AUTO: You will be able to change the Day/Night mode automatically. Motion Detection Setting The motion detection detects the moving objects in the scene by monitoring changes in brightness level. You can select the level of sensitivity for motion detection to 4 zone.
Menu Operation 5. 6. Use [UP] or [DOWN] to select an option then use [LEFT] or [RIGHT] button to adjust the option. • HEIGHT: Enlarge or decrease the vertical size of the mask. • WIDTH: Enlarge or decrease the horizontal size of the mask. • MOVE Y: Moves vertical position of the mask. • MOVE X: Moves horizontal position of the mask. Use [SENSITIVITY] option to obtain the optimum detection level. 3D-DNR Setting 1. Select [3D-DNR] option.
Menu Operation Privacy Setting This function is aiming at the protection of personal privacy, selecting a screen part black not to be displayed in the screen. Up to 8 zones can be registered. WHITE or BLACK on the COLOR option. 6. Use [UP] or [DOWN] to select an option then use [LEFT] or [RIGHT] button to adjust the option. • HEIGHT: Enlarge or decrease the vertical size of the mask. • WIDTH: Enlarge or decrease the horizontal size of the mask. • MOVE Y: Moves vertical position of the mask.
Menu Operation Special Menu Settings This menu lets you adjust and set up D-ZOOM, D-EFFECT, SHARPNESS, STABILIZER, COLOR, SYNC, USER TITLE, LANGUAGE function by yourself in the SPECIAL menu. 1. Select [SPECIAL] option. 2. Press [SET] button and the SPECIAL menu appears. Setting the D-ZOOM (Digital Zoom ) level You can select the digital zoom level. 32 1. Select [D-ZOOM] option on the [SPECIAL] menu. 2. Use [LEFT] or [RIGHT] button to select a [ON] then press [SET] the DIGITAL ZOOM menu appears.
Menu Operation Setting the D-EFFECT (Digital effect) Setting the SHARPNESS effect You can select the digital effect. The degree to which the boundary of the two portions is clearly distinguished. 1. Select [D-EFFECT] option on the [SPECIAL] menu. 2. Use [LEFT] or [RIGHT] button to select a digital effect. • V-FLIP: Flip the picture vertically. • MIRROR: Turn on the mirror effect. • ROTATE: Rotate the picture. (180°) • OFF: Turn off the digital effect. 1.
Menu Operation Stabilizer setting Setting the COLOR effect The image stabilizer function minimizes the appearance of shaky images caused by low-frequency vibration. You can switch the displayed picture to gray scale or color. This function is useful for outdoor surveillance. Select [STABILIZER] option and set to ON or OFF. 1. 2. Note: If you set the [STABILIZER] to ON, the Digital zoom is set to [x1.1] automatically. 34 Select [COLOR] option on the [SPECIAL] menu.
Menu Operation Setting the SYNC (Synchronization) The SYNC function is available only with AC power source. 1. Select [SYNC] option on the [SPECIAL] menu. 2. Use [LEFT] or [RIGHT] button to select [INT] or [LL] (Line Lock). • INT: Selects for using the internal synchronization. • LL (Line Lock): Selects for the operation of multi cameras because it synchronizes the camera phase by using the external signal (AC power signal). 2-1. Select [LL] mode and press [SET]. 2-2.
Menu Operation 2. Use [LEFT] or [RIGHT] button to select a [ON] then press [SET]. The USER TITLE menu appears. Language Setting Select the viewer language for the camera setup menu and OSD information display. A 3. Use [UP], [DOWN], [LEFT] or [RIGHT] button to select a character or number then press [SET] button. • CLR: Clear all entered characters and numbers. • POS: Move the USER TITLE position on the screen using the arrow buttons. • END: Confirm your selection or exit the setting.
Menu Operation Reset Settings 4. 1. • CAMERA REBOOT: To reboot the camera system. • FACTORY RESET: To reset the camera setting to factory setting, select [FACTORY RESET] option. Press [SET] button to confirm your selection. Select [RESET] option. 2. Press [SET] button and the RESET menu appears. 3. Use [UP] or [DOWN] to select option.
Specification ITEM LS521N-B1 Signal System NTSC Total/Effective Pixels 410 000 Pixels / 380 000 Pixels LS521P-B1 470 000 Pixels / 440 000 Pixels Pick-up Device 6 mm SUPER HAD CCD II Lens C/CS Mount Lens Signal Process XDI-S2 Synchronization System Internal / Line Lock Scanning Frequency (H) 15.734 kHz Scanning Frequency (V) 59.94 Hz(VD) 15.625 kHz 50 Hz(VD) Resolution More than 650 TV Lines S/N Ratio More than 50 dB (AGC Off, F1.
Specification ITEM LS521N-B1 LS521P-B1 Iris Control LS521P-C DC/VIDEO Day & Night Digital Day & Night Gain Control OFF/LOW/MIDDLE/HIGH Exposure ALC/ELC Shutter Speed White Balance Power Source 1/60 to 1/90 000 1/50 to 1/90 000 ATW/ AWCbPUSH /MANUAL DC 12 V / AC 24 V AC 230 V Power Consumption 4.4 W Operation Temperature -10 ˚C to 50 ˚C (Humidity: 0 % RH to 80 % RH) Storage Temperature -20 ˚C to 60 ˚C (Humidity: 0 % RH to 85 % RH) Weight Dimension (W x H x D) 380 g 472 g 67.4 x 61.
AB28
