Owner's Manual

ManualsBrandsLG ManualsSecurity CamerasLPT-OS551HQ

Dome Camera

Owner’s Manual

MODEL: LPT-OS551HQ

LPT-OS553HQ

Before installing and using the camera, please read this owner's

manual carefully and retain for future reference.

LPT-OS553HQ_ENG_6602 7/19/07 2:08 PM Page 1

Summary of content (32 pages)

PAGE 1
LPT-OS553HQ_ENG_6602 7/19/07 2:08 PM Page 1 Dome Camera Owner’s Manual MODEL: LPT-OS551HQ LPT-OS553HQ Before installing and using the camera, please read this owner's manual carefully and retain for future reference.
PAGE 2
LPT-OS553HQ_ENG_6602 7/19/07 2:08 PM Page 2 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
PAGE 3
LPT-OS553HQ_ENG_6602 7/19/07 2:08 PM Page 3 IMPORTANT SAFETY INSTRUCTIONS CAUTION: PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS IN THIS OWNER’S MANUAL. AND THOSE MARKED ON THE PRODUCT. RETAIN THIS BOOKLET FOR FUTURE REFERENCE. This product has been designed and manufactured to assure personal safety. Improper use can result in electric shock or fire hazard. The safeguards incorporated in this product will protect you if you observe the following procedures for installation, use, and servicing.
PAGE 4
LPT-OS553HQ_ENG_6602 7/19/07 2:08 PM Page 4 Introduction Contents About Dome Camera Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-7 The dome cameras are designed for installation in an indoor/outdoor video surveillance system. IMPORTANT SAFETY INSTRUCTIONS . . . . . . . .3 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 About Dome Camera . . . . . . . . . . . . . . . . . . . .4 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 5
LPT-OS553HQ_ENG_6602 x x x x 7/19/07 2:08 PM Page 5 Pattern Function A routine of manual operations can be stored for 5 minutes at the maximum and reproduced repetitively. The Panning, Tilting and Zoom controls are available for recording the pattern. Note: The available total time of pattern differs depending on camera’s operation. When the time is over, the pattern setup will automatically stop. Privacy Mask Privacy zone feature enables users to veil unwanted zones.
PAGE 6
LPT-OS553HQ_ENG_6602 7/19/07 2:08 PM Page 6 Safety Precautions 6 x Do not attempt to disassemble the camera To prevent electric shock,do not remove screws or covers. There are no user serviceable parts inside. Ask a qualified service personnel for servicing. x Avoid the camera with direct sunlight Do not aim the camera at bright objects.Whether the camera is in use or not, never face it with direct sunlight or other extremely bright objects. Otherwise blooming or smear may be caused.
PAGE 7
LPT-OS553HQ_ENG_6602 7/19/07 2:08 PM Page 7 Identification of Camera 4 5 1 6 7 2 “A” 8 3 1 Camera mounting bracket 2 Dome camera body 3 Dome cover 4 Power cable (DC 12V) 5 Video output cable with BNC connector Connects with the video connector of the monitor. 6 Data Communication Port (RJ45) - RS-485 and Alarm Input 7 Data Communication Port (RJ45) - RS-485 and Alarm Input 8 Fall Prevention Wire Be sure to hook the fall prevention wire into an bracket.
PAGE 8
LPT-OS553HQ_ENG_6602 7/19/07 2:08 PM Page 8 Installation Precautions • The following steps of installation and connection work should be done by qualified service personnel or system installers and should conform to all local codes. • Be sure to switch the camera off before installation and connection. • Do not install the camera near the air outlet of an air conditioner. • Do not touch the dome cover’s window.
PAGE 9
LPT-OS553HQ_ENG_6602 7/19/07 2:08 PM Page 9 Pendant mount (Optional) Wall mount (Optional) ■ How to install “A” Pipe threads should be clean and rust free. Use a sealer (such as Teflon™ tape or silicone sealer) on the threads. Add thread sealing tape Reference: Specifications of LG Standard pipe. Note: Do not remove the block (A) to keep the gap (B) between the camera body and installation bracket.
PAGE 10
LPT-OS553HQ_ENG_6602 7/19/07 2:08 PM Page 10 Setting the Switch Switch position (SW101) The DIP switch of the camera is two 4-bit switches and employs RS-485 communication mode as basic use. Switch settings are read into the camera when the power is turned on. Make sure to turn it off, then turn it back after changing the switch settings.
PAGE 11
LPT-OS553HQ_ENG_6602 7/19/07 2:08 PM Page 11 BAUD RATE The table for the camera ID setting (OFF OFF OFF OFF) 9,600 BPS (OFF OFF OFF ON) 1,200 BPS (OFF OFF ON OFF) 2,400 BPS (OFF OFF ON ON) 4,800 BPS (OFF ON OFF OFF) 19,200 BPS (OFF ON OFF ON) 38,400 BPS (OFF ON ON OFF) 57,600 BPS (OFF ON ON ON) 115,200 BPS ID 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 Switch position (SW104) ON 1
PAGE 12
LPT-OS553HQ_ENG_6602 ID 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 12 SW1 ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON 7/19/07 SW2 OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OF
PAGE 13
LPT-OS553HQ_ENG_6602 ID 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 SW1 ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON SW2 ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF
PAGE 14
LPT-OS553HQ_ENG_6602 7/19/07 2:08 PM Page 14 Connections Connection Preview DC 12V Video output BNC plug data port Ethernet cable data port Ethernet cable Precautions RS-485 Connection • Use the cable that is described below for RS-485 site communication. • Shielded, twisted pair cable • Low impedance • Wire gauge size is thicker than AWG #22 (0.33 mm2). • The connections should be made by qualified service personnel or system installers in accordance with all local codes.
PAGE 15
LPT-OS553HQ_ENG_6602 7/19/07 2:08 PM Page 15 ALARM IN Connections An 8-pin harness are supplied with the camera as standard accessories. Connect external sensors to this connector. Input specifications are low-active, non-voltage contact (ON when active) or open collector (Low when active). • Auto mode: Change the observe position to a sensor that senses a touch or shock then return to the position that previously observed. . (Set the Duration Time of Alarm Input function to “1 to 255”.
PAGE 16
LPT-OS553HQ_ENG_6602 7/19/07 2:08 PM Page 16 Alarm Input function Listed below are the camera actions of alarm input function by different function status in each mode Function status 16 Manual mode Auto mode While observe a specific position. Change the observe position to the alarmed position then keep observe the alarmed position. Change the observe position to the alarmed position then return to the position that previously observed. While operating Preset Tour function.
PAGE 17
LPT-OS553HQ_ENG_6602 7/19/07 2:08 PM Page 17 System Connection Note: When any peripheral is turned off and turned on again, the camera is also turned off and turned back on. Caution: Connect the supplied termination adapter to the final camera’s data port to prevent the RS-485 communication error.
PAGE 18
LPT-OS553HQ_ENG_6602 7/19/07 2:08 PM Page 18 Setup Menu Setup Menu Overview Setup menus are shown in the table below. You can adapt the camera to your requirements by setting up the respective items in these menus. These menus are described on the following pages for reference. Switches and keys on the controller are used in the setup operations.
PAGE 19
LPT-OS553HQ_ENG_6602 7/19/07 2:08 PM Page 19 Setting Camera Menu The buttons on the connected controller are used for setup. LCC-K1000 Controller (Optional) OSD button FOCUS FOCUS MODE FOCUS DIST ZOOM START ZOOM END ZOOM SPEED ZTRK MODE INITIAL SET RETURN PUSH AUTO 50CM x1 x54 QUICK AUTO ON 4. Use ZOOM (In/Out) to select a submenu option. 5. Use FOCUS (Near/Far) to select a value. CLR (CLEAR) button Arrow buttons SEL (SELECT) button ZOOM buttons FOCUS buttons 6.
PAGE 20
LPT-OS553HQ_ENG_6602 7/19/07 2:08 PM Page 20 Camera Identification Setting Only displays the camera’s ID. Use the internal 8 bit-DIP switch if you want to set ID. • Camera ID 0 can control all of camera independent of camera ID number. MENU CAMERA ID 0 FOCUS SET AWB SET AE MODE AE LEVEL SPECIAL SET MOTION DET F OSD DISP P MASKING EXIT Focus Settings To avoid AF error or out of Focus,initialization of LENS system by using the "Remote Reset" command of Controller is highly recommended.
PAGE 21
LPT-OS553HQ_ENG_6602 7/19/07 2:08 PM Page 21 Zoom Start setting Zoom Speed setting Selects a zoom start position. Selects a zoom speed. Select [ZOOM START] option on the [FOCUS] menu, then select a zoom’s start position. (x1 - x26) Select [ZOOM SPEED] option on the [FOCUS] menu, then select a zoom speed.
PAGE 22
LPT-OS553HQ_ENG_6602 7/19/07 2:08 PM Page 22 White Balance Control Settings You can set the white balance options using the [AWB] menu. General Operation 1. Move the cursor to [AWB SET] on the [MENU] screen MENU CAMERA ID 0 FOCUS SET AWB SET AE MODE AE LEVEL SPECIAL SET MOTION DET F OSD DISP P MASKING EXIT 2. Press the right key and the AWB setting menu appears. AWB WBC MODE AUTO RED ADJUST NOT USED BLUE ADJUST NOT USED INITIAL SET ON RETURN 3. Move the cursor to the desired option. 4.
PAGE 23
LPT-OS553HQ_ENG_6602 7/19/07 2:08 PM Page 23 Exposure Settings You can set the exposure options using the [AE] menu. General Operation 1. Move the cursor to [AE] on the [MENU] screen MENU CAMERA ID 0 FOCUS SET AWB SET AE MODE AE LEVEL SPECIAL SET MOTION DET F OSD DISP P MASKING EXIT 2. Press the right key and the exposure setting menu appears.
PAGE 24
LPT-OS553HQ_ENG_6602 7/19/07 2:08 PM Page 24 Automatic Gain Control (AGC) setting Backlight Setting If the images are too dark, change the maximum [AGC] value to make the images lighter. This option is available only when [AE MODE] is set to [SLOW MAN] or [SHUT MAN]. Improves an image that is darkened because of backlighting. Select [AGC ADJUST] option on the [AE] menu, then select a value.
PAGE 25
LPT-OS553HQ_ENG_6602 7/19/07 2:08 PM Page 25 Electronic Sensitive setting Shutter Speed Setting The electronic sensitivity enhancement function varies the shutter speed to increase the sensitivity in low light conditions. You can select a shutter speed from among AUTO, 1/120, 1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/10000, 1/20000 and 1/50000 seconds. This option is available only when [AE MODE] is set to [AUTO] and [FLICKERLESS] option is set to [OFF].
PAGE 26
LPT-OS553HQ_ENG_6602 7/19/07 2:08 PM Page 26 Auto Exposure Level Settings You can set the auto exposure options using the [AE LEVEL] menu. General Operation 1. Move the cursor to [AE LEVEL] on the [MENU] screen MENU CAMERA ID 0 FOCUS SET AWB SET AE MODE AE LEVEL SPECIAL SET MOTION DET F OSD DISP P MASKING EXIT 2. Press the right key and the auto exposure level setting menu appears.
PAGE 27
LPT-OS553HQ_ENG_6602 7/19/07 2:08 PM Page 27 Special Settings You can set the special options using the [SPECIAL] menu. General Operation 1. Move the cursor to [SPECIAL SET] on the [MENU] screen MENU CAMERA ID 0 FOCUS SET AWB SET AE MODE AE LEVEL SPECIAL SET MOTION DET F OSD DISP P MASKING EXIT 2. Press the right key and the [SPECIAL] setting menu appears. User Title Setting You can name the camera independently. 1. Move the cursor to [USER TITLE] on the [SPECIAL] menu. Arrow mark appears. 2.
PAGE 28
LPT-OS553HQ_ENG_6602 7/19/07 2:08 PM Page 28 Color Setting Digital Effect Setting You can switch the displayed picture to grayscale or color. You cannot set a Digital Effect option. Select [COLOR] option on the [SPECIAL] menu, then select an option (ON or OFF). Set to [ON] to display the picture with color. Set to [OFF] to display the picture with grayscale.
PAGE 29
LPT-OS553HQ_ENG_6602 7/19/07 2:08 PM Page 29 Motion Detection Setting The motion detection detects the moving objects in the scene by monitoring changes in brightness level. You can select the level of sensitivity for motion detection. When this camera is connected to a compatible intelligent CCTV system, the camera transmits an alarm signal by multiplexing it with the video signal. 1.
PAGE 30
LPT-OS553HQ_ENG_6602 7/19/07 2:08 PM Page 30 Privacy Masking Settings Using the LCC-K1000 or controller with Multix protocol for Privacy Zone Setting. This function is aiming at the protection of personal privacy, selecting a screen part black not to be displayed in the screen. Up to 8 zones can be registered. Submenus are provided for zone number selection and parameter setting. To register a new privacy zone using the LCC-K1000 1. Press the Set Up button then select the [PRIVACY ZONE] icon. 5.
PAGE 31
LPT-OS553HQ_ENG_6602 7/19/07 2:08 PM Page 31 Reference Specifications Signal System NTSC (High Resolution) Pick-Up Device PAL (High Resolution) 1/4” EX-view HAD CCD Total Pixels No. 410K S/N Ratio 470K More Than 50 dB Horizontal Resolution More Than 520 TV Lines Lens X 27 Zoom (F 1.5(W), F 3.8(T) f=3.25-88.0 mm) Shooting Distance Tele (1.2m), Wide (0.01 m) On Screen Display On/Off Minimum Illumination 1 Lux (F1.5, normal shutter) 0.
PAGE 32
LPT-OS553HQ_ENG_6602 7/19/07 P/NO : MFL40426602 2:08 PM Page 32