LP133WH2 Liquid Crystal Display Product Specification SPECIFICATION FOR APPROVAL ( ) Preliminary Specification ( ) Final Specification 13.3” HD TFT LCD Title Forte BUYER SUPPLIER *MODEL MODEL Suffix LG Display Co., Ltd. LP133WH2 TLA2 *When you obtain standard approval, please use the above model name without suffix APPROVED BY SIGNATURE APPROVED BY SIGNATURE K. J. KWON / S.Manager / REVIEWED BY G. J. Han / Manager / PREPARED BY / C. Y. Kim / Engineer S. C.
LP133WH2 Liquid Crystal Display Product Specification Contents No ITEM Page COVER CONTENTS 1 RECORD OF REVISIONS 2 1 GENERAL DESCRIPTION 3 2 ABSOLUTE MAXIMUM RATINGS 4 3 ELECTRICAL SPECIFICATIONS 3-1 ELECTRICAL CHARACTREISTICS 5 3-2 INTERFACE CONNECTIONS 6 3-3 SIGNAL TIMING SPECIFICATIONS 8 3-4 SIGNAL TIMING WAVEFORMS 8 3-5 COLOR INPUT DATA REFERNECE 9 3-6 POWER SEQUENCE 10 4 OPTICAL SFECIFICATIONS 11 5 MECHANICAL CHARACTERISTICS 15 6 RELIABLITY 18 7 INTERNATIONAL
LP133WH2 Liquid Crystal Display Product Specification RECORD OF REVISIONS Revision No Revision Date 0.0 Ver. 0.0 18. Sep. 2008 Page - Description First Draft 9, Dec.
LP133WH2 Liquid Crystal Display Product Specification 1. General Description The LP133WH2 is a Color Active Matrix Liquid Crystal Display with an integral LED backlight system. The matrix employs a-Si Thin Film Transistor as the active element. It is a transmissive type display operating in the normally white mode. This TFT-LCD has 13.3 inches diagonally measured active display area with WXGA resolution(1366 horizontal by 768 vertical pixel array).
LP133WH2 Liquid Crystal Display Product Specification 2. Absolute Maximum Ratings The following are maximum values which, if exceeded, may cause faulty operation or damage to the unit. Table 1. ABSOLUTE MAXIMUM RATINGS Values Parameter Symbol Min Max Units Notes Power Input Voltage VCC -0.3 4.0 Vdc at 25 ± 5°C Operating Temperature TOP 0 50 °C 1 Storage Temperature HST -20 60 °C 1 Operating Ambient Humidity HOP 10 90 %RH 1 Storage Humidity HST 10 90 %RH 1 Note : 1.
LP133WH2 Liquid Crystal Display Product Specification 3. Electrical Specifications 3-1. Electrical Characteristics The LP33WH2 requires two power inputs. The first logic is employed to power the LCD electronics and to drive the TFT array and liquid crystal. The second backlight is the input about LED BL.with LED Driver. Table 2. ELECTRICAL CHARACTERISTICS Values Parameter Symbol Min Typ Max Unit Notes LOGIC : Power Supply Input Voltage VCC 3.0 3.3 3.
LP133WH2 Liquid Crystal Display Product Specification 3-2. Interface Connections This LCD employs two interface connections, a 40 pin connector is used for the module electronics interface and the other connector is used for the integral backlight system. The electronics interface connector is a model UJU 20455-040E manufactured by UJU. Table 3.
LP133WH2 Liquid Crystal Display Product Specification 3-3. LVDS Signal Timing Specifications 3-3-1. DC Specification Symb ol Min Max Unit Notes LVDS Differential Voltage |VID| 100 600 mV - LVDS Common mode Voltage VCM 0.6 1.8 V - LVDS Input Voltage Range VIN 0.3 2.1 V - Description 3-3-2.
LP133WH2 Liquid Crystal Display Product Specification < Clock skew margin between channel > Freq. Fmax ' ' DFOUFS %&7 Fcenter Fmin '.0% Time < Spread Spectrum > 3-3-3.
LP133WH2 Liquid Crystal Display Product Specification 3-4. Signal Timing Specifications This is the signal timing required at the input of the User connector. All of the interface signal timing should be satisfied with the following specifications and specifications of LVDS Tx/Rx for its proper operation. Table 4. TIMING TABLE *5&. 4ZNCPM DCLK Hsync .J 6OJU 72.
LP133WH2 Liquid Crystal Display Product Specification 3-6. Color Input Data Reference The brightness of each primary color (red,green and blue) is based on the 6-bit gray scale data input for the color ; the higher the binary input, the brighter the color. The table below provides a reference for color versus data input. Table 5. COLOR DATA REFERENCE Input Color Data RED Color GREEN MSB R5 Black Red Green Basic Blue Color Cyan Magenta Yellow White RED (00) RED (01) RED GREEN BLUE Ver. 0.
LP133WH2 Liquid Crystal Display Product Specification 3-7. Power Sequence 90% 90% Power Supply Input VCC 10% 0V 10% T1T2 Interface Signal, Vi LVDS T5 T6 Valid Data T7 0V T4 T3 LED input Voltage VLED T11 T8 0V Valid Data Dimming control signal Of LED BL PWM 0V (Low) T9 LED on/off control Signal LED_EN T10 0V (Off) Table 6. POWER SEQUENCE TABLE Value Parameter Units Min. Typ. Max. T1 0.
LP133WH2 Liquid Crystal Display Product Specification 4. Optical Specification Optical characteristics are determined after the unit has been ‘ON’ and stable for approximately 20 minutes in a dark environment at 25°C. The values specified are at an approximate distance 50cm from the LCD surface at a viewing angle of Φ and Θ equal to 0°. FIG. 1 presents additional information concerning the measurement equipment and method. FIG.
LP133WH2 Liquid Crystal Display Product Specification Note) 1. Contrast Ratio(CR) is defined mathematically as Surface Luminance with all white pixels Contrast Ratio = Surface Luminance with all black pixels 2. Surface luminance is the average of 5 point across the LCD surface 50cm from the surface with all pixels displaying white. For more information see FIG 1. LWH= Average(L1,L2, … L5) 3.
LP133WH2 Liquid Crystal Display Product Specification FIG. 2 Luminance H C A L6 D L8 L7 H,V : ACTIVE AREA A : H/4 mm B : V/4 mm C : 10 mm D : 10 mm POINTS : 13 POINTS L3 V B L2 L1 L9 L10 Center Point L4 L5 L12 L11 L13 FIG. 3 Response Time The response time is defined as the following figure and shall be measured by switching the input signal for “black” and “white”.
LP133WH2 Liquid Crystal Display Product Specification 5. Mechanical Characteristics The contents provide general mechanical characteristics for the model LP133WH2. In addition the figures in the next page are detailed mechanical drawing of the LCD. Outline Dimension Horizontal 306.2 ± 0.50mm Vertical 177.6 ± 0.50mm Depth 3.5mm(Max.) Horizontal 296.62 mm Vertical 168.17 mm Horizontal 293.42mm Vertical 164.97 mm Bezel Area Active Display Area Weight Surface Treatment Ver. 0.0 300g(Max.
LP133WH2 Liquid Crystal Display Product Specification Ver. 0.0 Note) Unit:[mm], General tolerance: ± 0.5mm 9, Dec.
LP133WH2 Liquid Crystal Display Product Specification Ver. 0.0 Note) Unit:[mm], General tolerance: ± 0.5mm 9, Dec.
LP133WH2 Liquid Crystal Display Product Specification 6. Reliability Environment test condition No. Conditions Test Item 1 High temperature storage test Ta= 60°C, 240h 2 Low temperature storage test Ta= -20°C, 240h 3 High temperature operation test Ta= 50°C, 50%RH, 240h 4 Low temperature operation test Ta= 0°C, 240h 5 Vibration test (non-operating) Sine wave, 5 ~ 150Hz, 1.5G, 0.
LP133WH2 Liquid Crystal Display Product Specification 7. International Standards 7-1. Safety a) UL 60950-1:2003, First Edition, Underwriters Laboratories, Inc., Standard for Safety of Information Technology Equipment. 7-2. EMC a) ANSI C63.4 “Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and Electrical Equipment in the Range of 9kHZ to 40GHz.
LP133WH2 Liquid Crystal Display Product Specification 8. Packing 8-1. Designation of Lot Mark a) Lot Mark A B C D E F G H A,B,C : SIZE(INCH) E : MONTH I J K L M D : YEAR F ~ M : SERIAL NO. Note 1. YEAR Year 2001 2002 2003 2004 2005 2006 2007 2008 2009 2010 Mark 1 2 3 4 5 6 7 8 9 0 Month Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec Mark 1 2 3 4 5 6 7 8 9 A B C 2. MONTH b) Location of Lot Mark Serial No. is printed on the label.
LP133WH2 Liquid Crystal Display Product Specification 9. PRECAUTIONS Please pay attention to the followings when you use this TFT LCD module. 9-1. MOUNTING PRECAUTIONS (1) You must mount a module using holes arranged in four corners or four sides. (2) You should consider the mounting structure so that uneven force (ex. Twisted stress) is not applied to the module. And the case on which a module is mounted should have sufficient strength so that external force is not transmitted directly to the module.
LP133WH2 Liquid Crystal Display Product Specification 9-3. ELECTROSTATIC DISCHARGE CONTROL Since a module is composed of electronic circuits, it is not strong to electrostatic discharge. Make certain that treatment persons are connected to ground through wrist band etc. And don’t touch interface pin directly. 9-4. PRECAUTIONS FOR STRONG LIGHT EXPOSURE Strong light exposure causes degradation of polarizer and color filter. 9-5.
LP133WH2 Liquid Crystal Display Product Specification APPENDIX A. Enhanced Extended Display Identification Data (EEDIDTM) 1/3 TBD Ver. 0.0 9, Dec.
LP133WH2 Liquid Crystal Display Product Specification APPENDIX A. Enhanced Extended Display Identification Data (EEDIDTM) 2/3 TBD Ver. 0.0 9, Dec.
LP133WH2 Liquid Crystal Display Product Specification APPENDIX A. Enhanced Extended Display Identification Data (EEDIDTM) 3/3 TBD Ver. 0.0 9, Dec.
