OWNER’S MANUAL Hybrid Digital Video Recorder Please read this manual carefully before operating your set and retain it for future reference. MODELS LE5016/LE5008 Series LE4016/LE4008 Series P/NO : MFL60560470 1012 (V1.
Safety Information 1 Safety Information 1 Safety Information CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
Safety Information LG Electronics hereby declares that this/these product(s) is/are in compliance with the essential requirements and other relevant provisions of Directive 2004/108/EC, 2006/95/EC, and 2009/125/ EC. LG Electronics Service Europe B.V. Veluwezoom 15, 1327 AE Almere. The Netherlands (Tel : +31-(0)36-547-8888) Disposal of your old appliance 1. When this crossed-out wheeled bin symbol is attached to a product it means the product is covered by the European Directive 2002/96/EC. 2.
Safety Information Safety warnings and Cautions 1 Safety Information The following are warnings and cautions for the safety of the users and for the prevention of any property damage. Please read the following carefully. WARNING • Turn off the system before installation. Do not plug in several electric devices to the same outlet. -- • -• This may cause fire, over heating or electric shock.
Safety Information 5 CAUTION Please beware of the following precautions before installing the DVR. Avoid positioning the product in any place where the unit may come into contact with moisture, dust, or soot. • Avoid placing in direct sunlight or near heating appliances. • Keep the product away from electric sparks or magnetic substances. • Do not place any conductive material through the ventilation grills. • Keep the system turned off before installation.
Contents Contents 3 4 5 Properties 27 Network 28 Network Streaming 28 DDNS 28 Date/Time Safety Information 29 NTP 29 Controller 3 29 Update 30 Backup 1 IMPORTANT SAFETY INSTRUCTIONS 2 31 7 Device settings Preparation 31 Camera 31 PTZ 8 32 IP Camera ATM/POS Introduction 8 Features 32 8 Accessories 33 9 11 12 Front Panel Rear Panel Remote Control 3 6 Configuration menu System settings 27 1 2 26 27 33 Storage Display settings 33 OSD 33 Sequence 34
Contents 43 44 44 Panic Recording Instant Playback Search and Playback 44 Date and Time Search 44 Event Search 45 Bookmark Search 45 ATM/POS Search 46 Export Search 47 78 81 7 Recording Time Table (250GB HDD) Specifications 1 2 Functions Available During Playback 5 LG Network Client Program 48 48 48 48 Introduction Recommended PC Requirements Before install the program Getting Started 48 Install the LG Network Client on your PC 48 Starting the LG Network Client 49 LG Network Cl
Preparation 2 Preparation 2 Preparation Introduction Model LE5016D (16 Channel) is used for the description, operation and details provided in this operating guide. Features • Automatic backup by schedule. • Image authentication (Watermark). • Three USB 2.0 ports for backup interface. • Setup configuration export/import with USB memory stick. • Easy system S/W update with USB memory stick. • Clients S/W can manage max 100 DVR servers.
Preparation 9 Front Panel Front of the LE5016/LE4016 series a c b d e f g h i j k 2 Preparation l m n o p q o r s t Front of the LE5008/LE4008 series a l a b c b m d n e f o p g h i q o r j k s t 1 (Power): Turns DVR on or off. Press and hold for more than 2 seconds to turn on or off. Indicator • NET: Lights when the network is connected. • HDD: Blinks when the HDD is accessed. • ALARM: Lights when the alarm out is in progress.
Preparation • 2 Sub-functions Preparation Button number Function Description 3/4 FOCUS / FOCUS + 5 OSD Accesses or removes the System Control Bar (OSD). 6 INFO Displays or removes system information. 7/8 IRIS - / IRIS + 9 ALM.OFF 10/0 LOG Displays or removes the System Log List. 11 SET Registers the PTZ camera’s preset position. 12 CLEAR Deletes a memorized preset position. 13 COPY Copies the recording data to an external device.
Preparation 11 Rear Panel Rear of the LE5016/LE4016 series a b c 2 Preparation d e f g h i Rear of the LE5008/LE4008 series a d e f g h j kl b i j m n o p q n k p l m c o a VIDEO INPUT: Connect the camera’s video output to these BNC connectors. b LOOP OUT: The signal from VIDEO INPUT connector is looped out to this connector. q c Power Cord Inlet (AC IN): Connect the power plug. d RS-485 Terminals: Connect RS-485 compatible cameras.
Preparation Remote Control Button POWER (1) LOCK Description Turns DVR on or off. Displays the lock menu to change user type or disable system operation. 2 ID Preparation MAIN Displays or removes the screen setup menu for MAIN monitor. SPOT Displays or removes the screen setup menu for SPOT monitor. ALM.OFF OSD Set the appropriate DVR system ID to operate via the IR Remote Controller when using the multiple DVR.
Installation 13 3 Installation Connections Precautions 3 Depending on the camera and other equipment there are various ways to connect the unit. Please refer to the camera manual or manuals for other devices as necessary for additional connection information. • Be sure to switch off the camera before installation and connection. Basic Connection Overview Connect the coaxial-type cameras Connect the Monitor, DVR, VCR, or others. Connect ATM/POS unit. For audio amplifier Connect power cord.
Installation Connecting Camera VGA Monitor connection Connect the video output of your camera to the unit, using a standard 75 Ω video coaxial cable with BNC connector. Connect the VGA jacks on the rear of the unit to the corresponding input jacks on the TV or monitor using the VGA cable. Camera connection VGA Monitor connection 3 Installation Connecting Display device This unit can be outputted simultaneously from the VGA and MAIN OUT jack.
Installation Connecting USB device USB device connection 15 Connecting ATM/POS Connect the ATM/POS unit to the ATM/POS port. ATM/POS device connection 3 Installation USB Memory device Insert the memory device into the USB port. The system automatically recognizes the device. Using a USB memory device the system software can be easily upgraded. NOTE • USB External device -- Connect the external device to the USB port. (Example: External HDD or other external storage).
Installation Connecting Network Connecting the PTZ device You can control and monitor the system via network. With the remote control (monitoring), you can change the system configuration or monitors the image via network. After the installation, check the network settings for the remote control and monitoring work. Connecting the PTZ serial communication lines to the RS-485 terminal.
Installation Connecting LKD1000 controller Connecting the LKD1000 controller to control the DVR. (Refer to the manuals of the LKD1000 controller for more details.). The LKD1000 controller have to be connected to the 2 (DATA 2) port as shown illustration. If you connect the LKD1000 controller to the 1 (DATA 1) port, the LKD1000 controller will not be activated.
Installation Alarm Output Connect the alarm device to the alarm output. Alarm signal output at an event occurrence. HDD INSTALLATION Note for Hard Disk Drive Alarm output connection The internal hard disk drive (HDD) is a fragile piece of equipment. Please follow the guidelines below when using the DVR to protect against possible HDD failure. We recommend that you back up your important recordings onto an external backup device in order to prevent accidental loss.
Installation 7. Connect the SATA cable to the SATA connector on the main board. 19 System Operation 8. Assemble the top case. 9. Fix the screws. 10. When you turn the power of the unit on, the new HDD is detected and formatted automatically. 1. Turn on the unit. System booting will commence. The LG logo image will be displayed on the main monitor during the system booting. Replacing the Hard Disk Drive 2. When the booting is complet the live window will be displayed.
Installation General Explanation of the Live Screen on the Main Monitor d Displays the current date and time. Displays the setup menu. Main Monitor Screen ab c f System Control Bar e f Displays the search menu. Displays the PTZ remote control window. 3 Installation Displays the screen division selection window for the main monitor. Displays the screen division selection window for the spot monitor. Displays the lock menu to change the user type or disable system operation.
Installation You can capture and save the current image in JPEG file format. You should connect the external device to save the capture image. Selecting the Main Monitor screen mode 1. Playback the recorded data. 1. Press MAIN or click the 2. Pause the playback at a desired point during playback. 3. Click this button. The device selection window is displayed. 21 You can select the live screen mode to display a full, 4-split, 6-split, 8-split, 9-split or 16-split screens on the main monitor.
Installation Selecting the Spot Monitor screen mode PTZ Camera Control You can select the live screen mode to full or 4-split screens on the spot monitor. You can control the cameras connected via the data port of RS-485 terminal. You must set the configuration between the PTZ camera and the DVR. 1. Press SPOT or Click the icon in the system control bar. Screen mode select menu of spot monitor is displayed on the main monitor. 2. Select screen mode. Selected Spot Channel Channel Buttons 1.
Installation To Register Preset Positions Setup for PTZ Cameras 1. Move the camera to a point you wish by using the , , , buttons. You can adapt the camera to your requirements by setting up the respective items in menus. 3. Select the preset number you wish to register. 1. Click the icon. The setup menu appears in the selected window of the main monitor. 4. Press ENTER or click the 2. Use 2. Press SET or click the 23 icon. icon. , The position and its number are memorized.
Installation Viewing System Information To view system information: 1. Press the INFO button or click the icon in the system NOTE Refer to the following system log list. No.
Installation Export the recorded data NOTE This unit can manually copy recorded images and audio from builtin HDD to the external recording devices. • Check the export device before you proceed. 1. Press COPY or click the • You can also use the COPY button on the front panel for export function. • You can export the recorded data only in the live mode. • If you use the external device, the external device has to be formatted on this unit. icon in the system control bar.
Installation Configuration menu Setting the Menu Using the Front Panel Buttons or Remote Control Buttons Front Panel The features and options of the DVR are configured through the menu. The operations of this unit can be set via a menu displayed on the main monitor. You can select and set the operational conditions by using the buttons on the front panel and the remote control or using a Mouse connected to the unit.
Installation System settings 27 Network Properties 3 DHCP: Select this option when a DHCP server is installed on the network to allow IP address assignment. With this setting, the IP address is assigned automatically. • IP Address: Enter the IP address. • DVR Name: Enter the DVR name using up to 20 characters. • Subnet Mask: Enter the subnet mask address. • Language: Select a language for the setup menu and information display. • Gateway: Enter the gateway address.
Installation Network Streaming • Host Name: Enter the host name you want to use. You can not use the “www”, “mail”, “http”, “ftp”, “com”, “lg”, “lge”, “lgddns”, “lgeddns”, “ddns” for host name. • Registered Host: The registered host name appears. • Update: Register the host name you typed in [Host Name] to LG DDNS server. How to register DDNS host name With the DDNS function, you can easily use LG DVR. When you use the DDNS function for the first time after you purchased LG DVR 1.
Installation NTP 29 Update 3 NTP: Marks up, if you want to synchronize the DVR’s date and time with those of the time server called NTP (Network Time Protocol) Specify the NTP server’s name. • Server: For most cases select public. The DVR will obtain the average time among 5 public servers (time.nist.gov, time-a.nist. gov, time-b.nist.gov, ntp.nasa.gov, clock.isc.org). • Private Time Server: Enter the private time server’s IP address or host name using the virtual keyboard. • Sync.
Installation Backup 3. Select the backup device. 4. Enter the date and/or time to start backup on the schedule start option. 5. Enter the day of week and/or time on the Time Range Start option. 6. Enter the day of week and/or time on the Time Range End option. 7. Select the [Estimation Size] icon and press ENTER. 8. Check the size of selected data and free space of USB device.
Installation NOTE The disc burning is carried out by a single session closed format. • If you use the CD/DVD writer device for backup, it is making ISO image and then writing the backup data to the CD/DVD. • You can see the backup progress status on the system control bar. • The estimated size of backup data is only the approximate size. So you must prepare sufficient space on the media to prevent lack of space.
Installation • PTZ Test: After the PTZ setting, you can test the pan/tilt function for the selected PTZ camera. You can see the test screen from the preview windows on the right side of the PTZ test option. --- ATM/POS b / B: Test the pan direction. v / V: Test the tilt direction. NOTE The supported PTZ camera list is on page 70 for reference. IP Camera 3 Installation • • Channel: Selects the desired channel to set the connected IP camera.
Installation Storage 33 Display settings OSD 3 Installation • Overwrite: -- ALL: Overwrite recording is possible when the normal partition and event partition of HDD have fully recorded. -- NORMAL PARTITION: Overwrite recording is possible for normal partition of HDD when the normal partition of HDD has fully recorded. -- -- • Channel Name: Mark up to display or remove the channel name in the channel window.
Installation Channel Composition Record settings Schedule A schedule recording can be activated at preset times, in a repeating pattern on selected weekdays. The DVR can record according to a schedule set by the user. It can also record manually regardless of date and time. The recording can be made either continuously or triggered by events (alarm and motion detection). The recording schedule screen displays one day of the week showing the schedule of all channels over a 24-hour period.
Installation • 35 Sky blue (Continuous+Sensor+Motion+Text event recording): Recording starts automatically from the preset time. When the sensor alarm signal has input, motion has been detected or the text input occurs within a designated time, change the continuous recording mode to occurred event recording mode and recording starts automatically. 5. Select the next time cell block of schedule time cell blocks to confirm the schedule time. 6.
Installation Checking the Special Day Schedule List 1. Press [ZOOM -] when the [SP] button is selected. The special day scheduled list appears. Normal Settings concerning normal recording. 2. Select a special day title on the list and press ENTER. The title color turns orange. 3. Select the [Edit] icon then press ENTER to edit the special day or press [ZOOM -] to delete the special day schedule. 4. Press ESC to exit the special day schedule list.
Installation • Quality: Selects the recording picture quality • Frame Rate: Selects the frame rate. The frame rate is the number of recorded frames per second. According to resolution, the frame rate is set automatically. • Prealarm: Specify the pre-event recording time. When the Event signal is detected, the DVR is recording the data before the event during the setting time. • Postalarm: Specify the post-event recording time.
Installation Event settings IP camera Settings concerning IP camera recording. Sensor 3 Installation • Ch: Displays the IP camera channel number. • Resolution: Selects the recording resolution. • Quality: Selects the recording picture quality • Frame Rate: Selects the frame rate. The frame rate is the number of recorded frames per second. According to resolution, the frame rate is set automatically.
Installation -- ENTER: Selects or cancels the motion detection area at the current cell position. -- Press ESC to exit the settings. NOTE ATM/POS Recording Information. Option setting NOTE • • To select the area: Drag & drop a cell to the right to select the motion detection area. -- To cancel area: Drag & drop a cell point of a selected cell area to the left to cancel the motion detection area.
3 Installation • Sensor On: Sends an e-mail when a sensor has occurred. • Motion Detection: Sends an e-mail when a motion detection has occurred. • Text In: Sends an e-mail when a text input is detected. • Admin Password Changed: Sends an e-mail when the administrator password has changed. • Video Loss: Sends an e-mail when a video signal from the camera has stopped because of a cable disconnection or malfunction of a camera. • Power On/Off: Sends an e-mail when power is on or off.
Installation Buzzer Marks up when you want to activate the selected option. 41 User settings Group Authority You can register a new user group with various access rights. 3 Sensor: Makes a sound when a sensor occurs. • Motion : Makes a sound when a motion is detected. • Text: Makes a sound when the DVR detects text input . • System: Makes a sound when a cooling fan is not activated or the HDD has bad sector. Installation • • Group ID: Select the group ID to assign authority.
Installation User You can set the user name for the selected User ID. 3 Installation 1. Select [User ID] from the drop-down list. 2. Enter the user name of the selected user ID. 3. Select the user group from the drop-down list. 4. Enter the Password. 5. Select the auto user logout time from the drop-down list. 6. Press the ESC button to display the confirmation window. 7. Select [OK] to save the setting or [Cancel] to cancel the setting.
Operation 43 4 Operation Instant Recording Images from a camera will be recorded on the built-in hard disk. Ensure all the cameras are connected and that time and date have been set correctly. Before you start recording, first check the repeat recording settings in the recording menu of the system setup, and then make the recording settings. NOTE • External recording devices can be used as copy areas for images recorded on the hard disk.
Operation Instant Playback 8. Press SETUP/ESC to exit the[Date/Time] menu. Using the calendar icon to select the date It is possible to play a recorded image without stopping recording. 1. Select a channel you want to playback. 2. Press bB (Play) button to play a recorded image of the previous 1 or 2 minutes of recording. The playback image will be displayed on the full screen window. 3. Press x (STOP) button to stop the playback. 1. Select calendar icon then press ENTER. 2.
Operation 7. Select the [Search] icon then press ENTER. The event list menu appears. 8. Select the recording data on the event list then press bB (Play) button, click [Play] or double click the selected data to start playback. The picture is displayed on the main monitor. 45 ATM/POS Search Search the recorded text information by ATM/POS device. This function is available with backup data of the internal or external HDD only. 9. Press STOP (x) to stop playback and return to the event list menu. 10.
Operation Export Search Search an exported data from the external device or internal DVD-ROM device. If you want to use this function, you have to connect the external device or insert the CD/DVD disc with exported data otherwise the warning message will be displayed. Check the export device before you proceed. 4 Operation 1. Use v/V button to select the [Export] icon then press ENTER. 2. Select the desired source device. 3. Select the [Search] icon then press ENTER.
Operation 47 Functions Available During Playback Button System Control Bar Remote Control Function Front panel Stop playback. Pause playback. Jump to the beginning of the current data that was recorded on the same date. (press the button for more than 2 seconds.) 4 Press repeatedly to select the required scan speed. (M, MB, MM , MBM or m, bm, mm, bmm) Press repeatedly to play frame-by-frame in pause mode. Press to play reverse or normal playback.
LG Network Client Program 5 LG Network Client Program Introduction Getting Started The LG Network Client program is an IP-Surveillance software that works with the LG DVR to provide video monitoring, recording setting and event management functions. The software has multiple search functions for recorded events. Remote viewing and playback are also possible with the use of the LG Network Client.
LG Network Client Program LG Network Client Overview Selected Menu Tab Menu Bar File End Backup Search 49 Use to stop and exit the backup search function. Software Update Use to upgrade DVR software or add/ upgrade PTZ protocols. Live window Tool Bar 1. Log-in the Network Client program as the permitted user who has the Group Setup authority. 2. Click this option. The Update setting window is displayed. 3. Select the update device from the list.
LG Network Client Program View Tools Help Language Select the language for LG Network Client program. Resolution Select the resolution of the LG Network Client program. Connection Information Displays the Connection List windows. Add, Edit or Delete the site name or group name in LG Network Client. E-Map Displays the E-Map pop-up windows. This function gives a visual overview of the cameras in your surveillance environment using the imported maps.
LG Network Client Program Operation and settings The DVR is connected to the network through the Broadband Router Register the Site Name or Group Name The first time LG Network Client is started, you should register a site name to control it by the LG Network Client program. The computer running LG Network Client program must be on the same network with DVR. 1. Select [Tools] > [Connection Information] option on the menu bar. The Connection List window is displayed. 2.
LG Network Client Program Disconnect the site name or group name NOTE 1. Select the required site name or group name. 2. Click the right mouse button on the site name or group name. Select the [Disconnect] option. The site name is disconnected and deactivated. • Configuration of camera view is set the first time only. This configuration setup is memorized for the next time and displayed as it is. 3. Repeat step 1 to 2 for disconnection. • About the camera view menu tree.
LG Network Client Program Instant playback Pan/Tilt/Zoom Tab It is possible to play a recorded image without stopping recording. You can control the PTZ cameras via the network. 1. Select the [Camera View] tab in the live mode. 1. Select the PTZ camera channel window in the camera view mode. 2. Select a channel you want to playback. 3. Select the date. The day is displayed in a blue text when recorded data exists. 4. Select playback start time.
LG Network Client Program To Register Preset Positions Log View Tab 1. Move the camera to a point you wish. You can see the system log list of selected site name. 2. Click the [SET] icon. 1. Select the [Log View] tab. 3. Select the preset number you wish to register. 2. Click the icon and select the day. (The selectable days are displayed in blue color.) 4. Click the icon. The position and its number are memorized. 5. Repeat steps 1 to 4 to add additional positions. 3. Click the icon.
LG Network Client Program 55 Event Search Tab Delete the favorite 1. Select the registered favorite name and click the right mouse button. Search a recorded picture by date and event type. 2. Select the [Delete Favorite] option. The selected favorite name is deleted. Using the Search function Date/Time Search Tab Use to search a recorded picture by specifying date, hour and minute. 1. Select the [Event Search] tab. 2. Click the icon and select the day.
LG Network Client Program ATM/POS Search Tab Search the recorded text information by ATM/POS device. This function is available with backup data of the internal or external HDD only. Date/Time • Date Format: Select the date display format. • Time Format: Select the time display format. • Time Zone: This option setting is not available in the client program. • Daylight Saving: Mark up when you use the daylight saving function. • Start Time: Select the Daylight Saving start time.
LG Network Client Program Device settings • Full Warning: When the HDD has overflowed a warning message is displayed. • Auto Delete: Set the auto delete date. If you set the auto delete date, the recorded data will be deleted except the data within the selected date period of time. The Auto Delete function is activated every 35 minutes. • Event Partition: This option setting is not available in the client program. 57 Display settings Camera • Channel: Select the channel number.
LG Network Client Program Motion Settings when the sensor alarm is occurs within a designated time. • Sensitivity: Set the sensitivity level for the created motion detection area. • M (Motion event recording): Recording starts automatically when motion is detected within a designated time. • Relay Output: Select the number of the RELAY-OUT terminal for the output alarm (relay) signal when motion is detected.
LG Network Client Program Schedule channel copy settings • Relay Output: Select the alarm (relay) output number for the RELAY-OUT terminal for the output alarm (relay) signal. • Preset: Select the preset number. When the input is activated, the camera moves to the selected preset position and the picture of the camera in that position appears on the monitor. 1. Select the day. 2. Click the [Schedule Copy] button to display the schedule copy setup window. 3. Select the source channel. 4.
LG Network Client Program Mail Emergency 1. Click the [Setup] button. 1. Click the [Setup] button. 2. Set the below options. 2. Set the below options. • • Notification: Marks up to notify the unit operating information according to notification settings by e-mail. If notification option is not set, the other options cannot be set. -- SMTP Server: Enter the SMTP Server address. -- SMTP Port: Enter the SMTP Port Number. Typically the port used for SMTP is 25.
LG Network Client Program • Group Name: If you select a one of the group number from the Group ID option, you can register the group name. Enter the group name. -- • Group Setup, Search/Play, Export, PTZ, Power Off, Instant Record: Set the authority for the selected group. Marks up the option to activate it. 61 Using the Export function You can copy the recorded images and audio data from the DVR unit to the PC.
LG Network Client Program Add the Map NOTE • • The exported data file name is made automatically as the [Server name_Channel number_export start time.exp(or “avi”)] type. If you do not assign the export directory, the export directory will be set to default directory and sub directory will be created with start date. • If you log-out from the network client, the export sequence will be terminated. • If you set the time for data that does not exist, the export function is not activated.
LG Network Client Program Additional Programs Emergency Agent Program The system sends a message according to the Notification and Emergency settings in the event setup menu. Emergency Agent Overview Display the received message list. Detailed view of the received message. 63 To activate the Emergency Agent program 1. Run the [LG Emergency Agent] program. The Emergency icon is displayed in the system tray. 2.
LG Network Client Program Export Viewer Program Playback control buttons You can playback from the export data on the PC using this program. The export viewer program is saved automatically when you install the client program or export the data. Jumps to the beginning of the file. Pauses playback. Export Viewer Overview Menu Bar Starts playback. Stops playback. Jumps to the end of the file.
LG Network Client Program Web Viewer Program 65 Live screen display window. Logging in the Web Viewer 1. Start the web browser. The recommended browser is Internet Explorer with Windows. 2. In the Address Box, enter “HTTP://” and the IP Address of the DVR. You can use the Host Name that you entered in the DDNS setup menu of the DVR. 3. Press the ENTER button on the keyboard and then the Web viewer and the Remote Login menu will be displayed. 4. Enter the User Name and Password. 5. Click the [OK] button.
Troubleshooting 6 Troubleshooting Check the following guide for the possible cause of a problem before contacting service. Symptoms Resolutions Check the power cable is connected correctly. The system power does not turn on. Check the input voltage is correct. If the system power does not turn on even if the power cable is connected correctly, please contact the service center. Check the monitor power cable is connected properly.
Troubleshooting Symptoms 67 Resolutions Check the audio recording option is correctly set for the camera you wish to record audio. Audio data recorded with video data is not playing. Check the speaker and audio (line input) on the rear of system are connected correctly. Check the connected speaker is working properly. If the camera connected to the system has a problem, make sure that the camera is not damaged by trying another camera into a working video output.
Troubleshooting Symptoms Resolutions E-mail reception failed without SMTP server setting. • Make sure the network is correctly set. • Make sure the mail address is input correctly. • Check the spam mail setting of the inputted mail address. (If you set the spam mail, some mails are deleted automatically or classified in the spam mail box) • Some of SMTP mail services do not support an E-mails from private SMTP servers. In this case use the public SMTP server.
Appendix 69 7 Appendix Recommended Devices Recommended USB Memory list No.
Appendix Supported function list for device Device Instant backup Schedule backup Export Configuration Import/Export CD/DVD O X O X USB memory O O O O USB HDD O O O O E-SATA HDD O O O O NOTE If you use a USB memory stick or USB HDD for configuration import/export you must disconnect the other external USB devices.
Appendix 71 Time zones Timezone Abbreviation Timezone Eniwetok, Kwajalein EK -12:00 Midway Island, Samoa MIS -11:00 Timezone name DST Hawaii HAW -10:00 Alaska ALA -09:00 -08:00 Pacific Time (US and Canada); Tajuana PST -08:00 -07:00 Mountain Time (US and Canada), Chihuahua, La Paz, Mazatlan, Arizona MST -07:00 -06:00 Central Time (US and Canada), Saskatchewan, Guadalajara, Mexico City, Monterrey, Central America CST -06:00 -05:00 Eastern Time (US and Canada), Indiana (East), B
Appendix Factory Default Configuration Settings 3rd level Default Setting Factory Default setting DVR Name NULL YES Language The option depends on the model.
Appendix NTP Controller Update Backup Device Camera Date (2010.01.01) NO Time Current Time NO Date Format YYYY/MM/DD YES Time Format 12 HR YES Time Zone The option depends on the model. NO Daylight Saving OFF NO Daylight Saving Start JAN, 1st, SUN, 00 NO Daylight Saving End JAN, 1st, SUN, 00 NO NTP OFF YES Server PUBLIC SERVER YES Private Time Server NULL YES Sync.
Appendix Channel CH 01 YES Port NONE YES Control ID 00 YES Protocol LG_MULTIX YES Baud Rate 9600 YES PTZ Test - - Channel IP 01 - Vendor NONE YES Model Name NULL YES Host Name NULL YES User Name NULL YES Password NULL YES Port 554 YES Test - - Interface Device NONE YES Camera CH 01 YES Baud rate 9600 YES Data Bits 8 YES Stop Bits 1 YES Parity NONE YES 7 Overwrite ALL YES Appendix Full Warning OFF YES Auto Delete OFF YES Event Partit
Appendix Schedule Normal Sensor Motion Text SUN S+M YES MON S+M YES TUE S+M YES WED S+M YES THU S+M YES FRI S+M YES SAT S+M YES SP S+M YES List - - Add - - Ch Copy - - Day Copy - - Ch - - Resolution 352X240 (NTSC)/352X288 (PAL) YES Quality STANDARD YES Frame Rate 30 (NTSC)/25 (PAL) YES Ch - - Resolution 352X240 (NTSC)/352X288 (PAL) YES Quality STANDARD YES Frame Rate 30 (NTSC)/25 (PAL) YES Prealarm OFF YES 7 Postalarm 10SEC YES Ch -
Appendix Instant/Panic IP Camera Event Sensor Motion 7 ATM/POS Data Format Appendix Event Popup Notification Ch - - Resolution 352X240 (NTSC)/352X288 (PAL) YES Quality STANDARD YES Frame Rate 30 (NTSC)/25 (PAL) YES Ch - - Resolution 352X240 (NTSC)/352X288 (PAL) YES Quality STANDARD YES Frame Rate 30 (NTSC)/25 (PAL) YES In - YES Sensor Type N.O.
Appendix Emergency Output Buzzer User Group Authority User Notification OFF YES SMTP Server NULL YES SMTP Port 25 YES User Name NULL YES Password NULL YES TLS OFF YES Mail Address 1 NULL YES Mail Address 2 NULL YES Mail Address 3 NULL YES E-mail Test - - Notification OFF YES Host name NULL YES Port 9002 YES Relay Off ALARM ACKNOWLEDGE YES System Alarm Out NONE YES Sensor OFF YES Motion OFF YES Text OFF YES System OFF YES Group ID GUEST YES G
Appendix Recording Time Table (250GB HDD) Recording Time(Hr) Resolution (NTSC/PAL) Quality LOWEST LOW 7 352x240 / 352x288 STANDARD Appendix HIGH HIGHEST FPS (NTSC/PAL) Video(NTSC/PAL) Video + Audio(NTSC/PAL) 8ch 16ch 8ch 16ch 30/25 1022/800 511/400 838/683 461/368 15/12.5 1188/1142 594/571 947/917 527/509 10/8 1508/1416 754/708 1139/1086 649/615 7.
Appendix LOW 704x240 / 704x288 STANDARD HIGH HIGHEST 30/25 563/425 281/212 502/389 265/203 15/12.5 764/602 382/301 657/533 353/283 10/8 899/771 449/385 753/661 410/356 7.5/6 949/888 474/444 788/746 431/405 5/5 1175/925 587/463 938/772 522/421 3/3 1235/980 617/490 976/810 545/443 1/1 1553/1337 777/669 1165/1039 666/585 30/25 469/330 235/165 426/308 223/159 15/12.5 625/465 312/233 551/423 293/222 10/8 724/577 362/288 627/513 336/272 7.
Appendix LOWEST LOW 704x480 / 704x576 7 STANDARD HIGH Appendix HIGHEST 30/25 302/236 151/118 284/224 146/115 15/12.5 430/337 215/169 394/315 206/163 10/8 470/435 235/217 427/398 224/208 7.5/6 573/516 287/258 511/465 270/245 5/5 712/536 356/268 618/481 331/254 3/3 876/683 438/342 738/596 401/318 1/1 1250/999 625/500 986/823 551/451 30/25 236/169 118/84 225/163 115/83 15/12.5 322/237 161/118 301/225 156/115 10/8 381/307 191/153 352/288 183/149 7.
Appendix 81 Specifications LE5008 Series LE5016 Series LE4008 Series LE4016 Series 8 16 Loop Through 8 16 Composite 1 1 VGA 1 1 Spot 1 1 Input 2 4 Output 2 2 Input 8 16 Output 2 4 Model Input Video Output Audio Alarm Pre-Alarm Recording NTSC Recording Frame Rate (/Second) PAL Search Serial I/F Network Security Up to 240 IPS @ 352x240 Up to 480 IPS @ 352x240 Up to 200 IPS @ 704x576 Up to 400 IPS @ 704x576 Up to 200 IPS @ 352x288 Up to 400 IPS @ 352x288 FF, FB,
Appendix Power AC Free 100~240 V, 50/60 Hz Power Consumption Maximum 80 W (with 4 HDD) Dimension (WxDxH) 430 mm x 430 mm x 96 mm Net Weight (without HDD) Operation Temp. / Humidity 7 6.85 kg 6.
AB28
