OWNER'S MANUAL Color Video Camera Please read this manual carefully before operating your set and retain it for future reference.
CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
• • Caution: Danger of explosion if battery is incorrectly replaced. Replaced only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions. Caution: This installation should be made by a qualified service person and should conform to all local codes. Holes in metal, through which insulated wires pass, shall have smooth well rounded surfaces or shall be provided with brushings.
LG Electronics hereby declares that this/these product(s) is/are in compliance with the essential requirements and other relevant provisions of Directive 2004/108/EC and 2011/65/EU. European Standards Centre: Krijgsman 1, 1186 DM Amstelveen The Netherlands Disposal of your old appliance 1. 2. 3. 4 This crossed-out wheeled bin symbol indicates that waste electrical and electronic products (WEEE) should be disposed of separately from the municipal waste stream.
Important Safety Instructions 1. Read these instructions. and the point where they exit from the apparatus. 2. Keep these instructions. 3. Heed all warnings. 11. Only use attachments/accessories specified by the manufacturer. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. 8.
Cautions for Safe Operation Power Supply Operating and storage location This camera must always be operated DC 12 V. Certified/ Listed Adaptor which comply with LPS. Avoid viewing a very bright object (such as light fittings) during an extended period. Avoid operating or storing the unit in the following locations. Handling of the unit Be careful not to spill water or other liquids on the unit. Be cautions not to get combustible or metallic material inside the body.
Contents Features.................................................................. 8 Part Names and Functions.................................... 9 Reset settings..................................................................32 Reference............................................................. 33 On Screen Display..........................................................33 Connections......................................................... 11 RS-485 Protocol (Optional)..........................
Features This color video camera is designed for use in monitoring system. • High resolution and high sensitivity with a 4.5 mm (1/4 Type) Super HAD CCD II.
Part Names and Functions a b c d POWER e S - VIDEO VIDEO OUT a Camera installation bracket The bracket can be fixed at the top or bottom of the S - VIDEO POWER camera. b Lens mount cap The cap is installed to protect the lens mount section. Remove the lens mount cap before install the camera. VIDEO OUT (sold separately) CONTROL CONTROL f + 12V DC - g h c Power indicator Comes on when the power to the camera is on.
Part Names and Functions near. • M(MENU) button: If you want to set up a diverse function, you can push this button. • W(WIDE) button: When push, picture is wide angle. • F(FAR) button: In a manual situation, focus get far. • H(HOT) button: When you set the DAY/NIGHT mode to EXT, you can change the Day/Night mode using this button. e Video output (S-Video type) Connect to the S-Video in connector of a monitor.
Connections Power connection Connecting Monitor 1. Remove the insulation on the power cable as illustrated. The video signal connection between the camera and the monitor or DVR. 2. Attach the terminal tips. 3. Connect to the 12V DC UL Listed, Class 2 Power Supply only on the camera.
Connections You can control the PTZ and RS-485 by a pin terminal on the back side of the camera.
7 NC 7 NC 7 Orange 7 Orange 8 TR- Violet TR+ TR- 8 9 8 Gray 10 GND TR+ 9 Violet 9 CN 8 312 TR- 10 Black Connections 10 GND • CN 312 TR- 9 TR+ • • 8 CN 312 TR- 10 GND Gray Black RxD RD TxD TD GND GND RD TD DTR SG DSR RTS CTS RI Zoom & Focus DC Control connect 9 TR+ TR+ TR- 1 TR+ CN 312 TR- RxD RD 9 TR+ TxD TD 10 GND GND GND 8 9 1 9TR+ TR- 2 CN 312 ZOOM10 RxD RD TR+ TxD TD ZOOM ( + : Tele, - : Wide ) GND GND GND COMMON COM 3 FOCUS FOCUS
Connections Schematic diagram of wired remote-control.
Connections The bracket can be installed to either the top of the camera as desired. When changing the position of the camera mounting bracket, you should always reuse the screws that have been removed. Note: If using a camera mounting bracket, select a location that is strong enough to bear the full weight of the camera and the mounting bracket for long periods, and install the camera and mounting bracket securely.
Menu Opertaion The following table shows the list of menu items and options. You can adapt the camera to your requirements by setting up the respective items in these menus.
Menu Operation Main Menu Sub Menu OFF Contents SMART MD MOTION DET ON REGIONAL MD OFF / ON ZONE NUMBER ZONE STATE WIDTH HEIGHT MOVE X MOVE Y MOTION ZOOM EXIT Main Menu Sub Menu OFF ZONE1 to ZONE4 ON, OFF 2 to 8 2 to 6 1 to 7 1 to 5 OFF, x1,...
Menu Operation Main Menu 3D-DNR Sub Menu OFF LOW MIDDLE HIGH CAMERA ID D-EFFECT COLOR FREEZE SHARPNESS STABILIZER SPECIAL OSD LANGUAGE RESET EXIT 18 INITIAL SET EXIT FACTORY RESET S/W VERSION REBOOT PROTOCOL EXIT Contents 0 to 255 OFF/ V-FLIP/ MIRROR/ ROTATE OFF ON COLOR LEVEL OFF/ ON 0 to 68 OFF/ ON OFF USER TITLE ZOOM MAG ON FUNCTION CAMERA ID ENG (The supported language can be different depending on the model.) RET / TOP / END LG / PELCO-D / PELCO-P RET / TOP / END General Operation 1.
Menu Operation and press [M] to exit the setup menu. • RET: Return to the previous. • TOP: Return to the CAMERA SETTING menu screen. • END: Exit the setup menu. Focus settings Notes: • [T] button: Use to move upper direction on the menu screen. • [W] button: Use to move lower direction on the menu screen. • [N] button: Use for increase the value of the option. The camera adjusts the focus automatically by sensing the center of the picture.
Menu Operation • ZOOM TRIG: The focus is activated manually. If you change the zoom, the focus is activated Automatically and then the focus mode is automatically changed to manual mode. Focus Distance setting Selects the minimum shooting distance for the focus. Select [FOCUS DISTANCE] option on the [FOCUS] menu, then select a focus distance value. Zoom Start setting You can set the zoom start position of the camera.
Menu Operation Exposure Settings AGC (Automatic Gain Control) setting If the images are too dark, change the maximum [AGC] value to make the images lighter. 1. Select [AGC] option on the [EXPOSURE] menu. 2. Use [N] or [F] button to select a value. WDR/BLC setting Iris setting Use WDR/BLC option to set the options for BLC or WDR camera. 1. Select [WDR/BLC] option on the [EXPOSURE] menu. Select the desired lens iris value for camera exposure. 2. Use [N] or [F] button to select a mode then press [M].
Menu Operation • BLC: Camera’s backlight compensation feature helps alleviate issues of visibility in high contrast areas. Set the BLC limit. • HSBLC: Use for masking brightness of the specific area to view the subject more clearly. The HSBLC mode is automatically activated only in low luminance scene. • - AREA SETTING: Use [N] or [F] button to select a area then use [T] or [W] button to select a ON or OFF. Press [M] to exit the area setting menu.
Menu Operation SENS-UP setting White Balance setting If pictures are not clear due to darkness, use for increase the sensitivity of picture. Select the method by which the camera shifts its output colors to compensate for the color of a light source. 1. Select [SENS-UP] option on the [EXPOSURE] menu. 2. Use [N] or [F] button to set the SENS-UP limit To setting the SENS-UP function, select the [AUTO] on the [SHUTTER].
Menu Operation • - When the scene contains mostly high color temperature objects, such as a blue sky or sunset. - When the scene is dim. AUTO: In this mode, the color temperature range for the proper white balance is approximately 2 700 °K to 5 400 °K. Proper white balance may not be obtained under the following conditions: - When the color temperature is out of the 2 700 to 5 400°K range. - When the scene contains mostly high color temperature objects, such as a blue sky or sunset.
Menu Operation Day/Night setting - DWELL TIME: Use [N] or [F] button to select a dwell time. - BURST MODE: Select [ON] or [OFF] to set the color burst in Night status. • DAY: Color mode enabled. • NIGHT: Black-and-white mode enabled. • EXT : Switches between color picture and black-andwhite picture when an external day/night switching signal is received. 1. Select [DAY/NIGHT] option on the [CAMERA SET] menu. 2. Use [N] or [F] button to select mode for day/night function.
Menu Operation Motion Detection setting - The motion detection detects the moving objects in the scene by monitoring changes in brightness level. You can select the level of sensitivity for motion detection to 4 zone. Use [N] or [F] button to select a zone number on the [ZONE NUMBER]. - Use [N] or [F] button to set up the ON or OFF on the ZONE STATE. - Use [T] or [W] to select an option then use [N] or [F] button to adjust the option. > HEIGHT: Enlarge or decrease the vertical size of the mask.
Menu Operation motion is detected. [MASK STATE] option. If you already registered the mask zone and set to ON, the mask zone box appears on the monitor. Privacy Mask setting 5. Select [RESET MASK] and press [M]. If you register the mask zone for the first time, the mask zone box appears on the center of the monitor. If you already registered mask zone, it will be returned to its initial state and appear on the center of the monitor. 6.
Menu Operation Notes: • If you want to reset the mask zone position, select RESET MASK option and press [M] button. • The parts with the registered mask numbers from MASK1 to MASK4 have the same color. (So do the parts with the numbers from MASK5 to MASK8.) 3D-DNR setting If you change the mask color, the registered mask color will be changed automatically with the same color for each of group. (MASK1 to MASK4, MASK5 to MASK8) 1. Select [3D-DNR] option. 2.
Menu Operation Special menu settings D-EFFECT (Digital effect) setting You can select the digital effect. 1. 2. Camera Identification setting You can use the camera identification (CAMERA ID) to assign a number to the camera. 1. Select [CAMERA ID] option on the [SPECIAL] menu. 2. Use [N] or [F] to select a CAMERA ID. Select [D-EFFECT] option on the [SPECIAL] menu. Use [N] or [F] button to select a digital effect. • V-FLIP: Flip the picture vertically. • MIRROR: Turn on the mirror effect.
Menu Operation Freeze setting Stabilizer setting 1. Select [FREEZE] option on the [SPECIAL] menu. 2. Use [N] or [F] button to set up the ON or OFF. The image stabilizer function minimizes the appearance of shaky images caused by low-frequency vibration. This function is useful for outdoor surveillance. Sharpness setting Select [STABILIZER] option and set to ON or OFF. Sharpens the image outline. Note: 1. Select [SHARPNESS] option on the [SPECIAL] menu. 2.
Menu Operation OSD setting You can set the Function On-Screen Display options using the [OSD] menu. The Function On-Screen Display of this camera can be turned on or off. 1. Select [OSD] option on the [SPECIAL] menu. 2. Use [N] or [F] button to select a [ON] and press [M]. The OSD menu appears. 3. Use [T] or [W] to select an option then use [N] or [F] button to set the option. 4. • ON: Displays the Function OSD on the screen. • OFF: The Function OSD does not appear on the screen.
Menu Operation Reset settings 1. Select [RESET] option. 2. Press [M] button and the RESET menu appears. 3. 32 Use [T] or [W] to select option. • FACTORY RESET: Clear certain settings and information and return to factory default settings. • S/W VERSION: Displays the software version on the monitor. • REBOOT: Reboot the camera system. • PROTOCOL: Select the protocol for the camera communication among the LG, PELCO-D and PELCO-P. 4. Press [M] to confirm your selection.
X20 X20 X20 X20 35 35 35 35 Reference 1 On Screen Display b cdefg 1 OSD Format Function Some of these functions will be displayed every time the camera is operated. a TITLE h None Display Auto Mode ijkl Focus a Mode TITLE Description Zoom Trigger Mode 35 X20 Manual Mode One Push Mode Displays when the Auto focus is operating. b Camera ID 0~255 X20 35 m n Displays the camera ID.
1 TITLE 1 TITLE 35 Reference 35 35 X20 X20 35 X20 Function 35 d e 35 White Balance Mode OSD Format None Display Backlight tion Mode X20 X20 Function g 3D-DNR One Push Mode h User Title Outdoor Backlight Compensation is turned off. WDR On BLC On OSD Format None Display X20 HSBLC On 34 35 35 Auto or ATW Mode Indoor None Display X20 X20 Manual Mode White Balance Manual Mode f Conpensa- Description 35 Day & Text: A to Z, 0 to 9, ‘-’, ‘.
Reference RS-485 Protocol (Optional) Data Communication Format • Data Length: 1 Byte (8 Bit) • Start/Stop Bit: 1 Bit • Parity Bit: None • Baud rate: 9,600 bps Format Byte 1 0xE5 Byte 2 0x87 Byte 3 Camera ID Byte 4 Byte 5 Byte 6 Byte 7 0x60 Key In or Key Out Key Code *C.S. *C.S. = Check Sum • The data of total 7 bytes is transmitted from the external RS-485 device to the camera. • Byte 7 : The value of Check Sum from ‘Byte 1 ’ to ‘Byte 6 ’.
Reference Commands Function Menu Tele (Menu Up) Wide (Menu Down) Near (Menu Right) Far (Menu Left) Command Key In E5 87 ID 60 00 14 CS Key Out E5 87 ID 60 FF 14 CS Key In E5 87 ID 60 00 08 CS Key Out E5 87 ID 60 FF 08 CS Key In E5 87 ID 60 00 04 CS Key Out E5 87 ID 60 FF 04 CS Key In E5 87 ID 60 00 02 CS Key Out E5 87 ID 60 FF 02 CS Key In E5 87 ID 60 00 01 CS Key Out E5 87 ID 60 FF 01 CS Note: You must enter the Key out command after the Key input commend.
Reference Specifications ITEM LCZ2850-DN LCZ2850-DP Signal System NTSC PAL Total Pixels Number 520 000 Pixels 610 000 Pixels Effective Pixels Number 480 000 Pixels 570 000 Pixels Image Device 4.5 mm (1/4 Type) Super HAD CCD II ISP XDI-II Lens x28 Zoom, F 1.5 (Wide End), F 3.7 (Tele End) Digital Zoom x 12 IRIS Control Auto / Manual Sync. System Internal Scanning Frequency (H/V) Horizontal Resolution 15.734 kHz / 59.94 Hz 15.
Reference ITEM LCZ2850-DN LCZ2850-DP S/N Ratio Minimum Illumination 52 dB (AGC Off ) B/W 0.01 lx (Sens-up OFF), 0.000 01 lx (Sens-up ON) Color 0.2 lx (Sens-up OFF), 0.003 lx (Sens-up ON) Video Output Signal 1 Vp-p Composite (75 Ω) Day & Night AUTO / DAY / NIGHT / EXT Backlight WDR / BLC / HSBLC / OFF DNR Electronic Shutter Speed 38 3D-DNR 1/60 to 1/120 000 1/50 to 1/120 000 White Balance AUTO / ATW / ONE PUSH / MANUAL Control Method RS-485 Power Source DC 12 V Power Consumption 3.
Reference ITEM LCZ2850-DN LCZ2850-DP Operation Temperature -10 ºC to 50 ºC Storage Temperature -20 ºC to 60 ºC Operation Humidity 0 % RH to 80 % RH Storage Humidity 0 % RH to 85 % RH Weight 420 g Dimension (H x V x D) 57 mm x 69 mm x 109 mm 39
