OWNER'S MANUAL IR Bullet Camera Please read this manual carefully before operating your set and retain it for future reference.
CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
• • Caution: Danger of explosion if battery is incorrectly replaced. Replaced only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions. Caution: This installation should be made by a qualified service person and should conform to all local codes. Holes in metal, through which insulated wires pass, shall have smooth well rounded surfaces or shall be provided with brushings.
LG Electronics hereby declares that this/these product(s) is/are in compliance with the essential requirements and other relevant provisions of Directive 2004/108/EC and 2011/65/EU. European Standards Centre: Krijgsman 1, 1186 DM Amstelveen The Netherlands Disposal of your old appliance 4 1. All electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities. 2.
Important Safety Instructions 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11. Only use attachments/accessories specified by the manufacturer. 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings.
Cautions for Safe Operation Operating and storage location Power Supply Avoid viewing a very bright object (such as light fittings) during an extended period. Avoid operating or storing the unit in the following locations. This camera must always be operated DC 12 V or AC 24 V. Certified/Listed Adaptor which comply with LPS.
Contents 3D-DNR Setting........................................................................23 Features.............................................................................. 8 Special Menu Settings...........................................................26 Accessories................................................................................... 8 Part Names and Functions..................................................... 9 Connections..................................................
Features Accessories This IR Bullet Camera is designed for installation in a video surveillance system. This manual contains instructions on how to install and manage the IR Bullet Camera in your video surveillance system. Sunshield and Fixing screw Should you require any technical assistance, please contact authorized service center. • High resolution and high sensitivity with a 6 mm (1/3 Type) CCD. • Day & Night function. • HSBLC/BLC covers various light conditions.
Part Names and Functions a b cd a Lens Cover b Angle adjuster Adjust the camera angle. c Tilt adjuster Adjust the tilt position. d Pan adjuster Adjust the pan position. e IR LED f IR Sensor e f gh i j g Focus lock lever Fixes the focus position after adjusting. h Zoom lock lever Fixes the zoom position after adjusting. i OSD menu control buttons j Video Out connector (BNC type) Use this jack for checking the picture with portable monitor when install the camera.
Connections Connecting Display device Precautions The video signal connection between the camera and the monitor. • Be sure to switch off the unit before installation and connection. • The installation should be made by qualified service personnel or system installers. • Do not expose the power and connection cables to moisture, which may cause damage to the unit.
Connecting RS-485 Device Connecting power source Use these ports to connect an external device of RS-485 format. Connect a power source to the input terminal with 2 and 3 aligned correctly, and then connect a power source to the power input terminal as shown below. (recommended power adapter is AC 24 V/0.5 A, DC 12 V/0.
Connecting Waterproof processing of cable Surely use the Butyl tape. 1. Connect and tape the cables. 2. 12 Bind the cables together with Butyl tape. Warning: • The cables are not waterproofed completely. So sealthe tube ends and the portions between cable cores as well as connecting portions with Butyl tape. • If not using the Butyl tape, it may cause water absorption from a gap and finally condensation and water leakage.
Menu Operation OSD Menu control buttons This camera utilizes an on-screen user MENU. To set items on the menu, use the following buttons. UP SET LEFT DOWN BUTTON Description UP Used to move upper direction on the menu screen. Use this button to select an item or adjust the parameters. DOWN Used to move lower direction on the menu screen. Use this button to select an item or adjust the parameters. RIGHT Moves the cursor to the right. Used to increment the value selected in the menu.
OSD Menu Overview The following table shows the list of menu items and options. You can adapt the camera to your requirements by setting up the respective items in these menus. Main Menu Sub Menu ALC /ELC SHUTTER OFF / AUTO EXIT RET/ TOP / END - AWC / SET KET MANUAL EXIT 14 RED BLUE SMART IR x512, ..., x2, AUTO, OFF, A.FLK, 1/160, ...
3D-DNR 0 to 100 OFF MASK SELECTION DISPLAY RECTANGLE PRIVACY MASK DISPLAY ON CIRCLE POLYGON EXIT POSITION ,/ POSITION ;. SIZE ,/ SIZE ;. MASK SELECTION POSITION ,/ POSITION ;. SIZE ,/ SIZE ;. RADIUS MASK SELECTION DISPLAY SHAPE POSITION RET/ TOP / END OFF D-ZOOM 1 to 8 OFF / MOSAIC / COLOR1 to COLOR8 2 to 98 2 to 98 4 to 100 4 to 100 1 to 4 OFF /MOSAIC / COLOR1 to COLOR8 0 to 100 0 to 100 1 to 15 1 to 15 0 to 100 1 to 2 SPECIAL D-EFFECT SHARPNESS COLOR SYNC USER TITLE LANGUAGE ZOOM x 1.
General Operation Exposure Settings 1. You can set the exposure options using the EXPOSURE menu. Press [SET] button. The Main OSD menu screen appears on the monitor. 2. Use [UP] or [DOWN] button to select an option then press [SET] button. Submenu appears on the monitor. 3. Use [UP] or [DOWN] button to select a submenu option. 4. Use [LEFT] or [RIGHT] button to select a value. 5. Select [EXIT] option then press [SET] to exit the setup menu.
Backlight setting Use Backlight option to view the object clearly in backlight conditions. • BLC: Camera's backlight compensation feature helps alleviate issues of visibility in high contrast areas. Set the BLC limit. Note: If the [DAY/NIGHT] option is set to [NIGHT] mode, the BLC mode of the [EXPOSURE] function is not available and [---] mark is displayed. • 1. Select [Backlight] option. 2. Use [LEFT] or [RIGHT] button to select a mode then press [SET].
• OFF: Not used. BRIGHTNESS setting You can increase the brightness of the darkened video. If you set the brightness to lower value, the image is darkened. If you set the brightness to higher value, the image gets bright. 1. Select [BRIGHTNESS] option. 2. Use [LEFT] or [RIGHT] button to set the bright level. 18 AGC (Automatic Gain Control) setting If the images are too dark, change the maximum [AGC] value to make the images brighter. But noise is increase. 1. Select [AGC] option. 2.
SHUTTER (Shutter Speed) setting SENS-UP setting Select the desired shutter speed for camera exposure. You can change the shutter speed to higher speed to capture fast-moving subjects, though the image becomes darker. If pictures are not clear due to darkness, this SENS-UP operation would increase the sensitivity of picture. 1. Select [SHUTTER] option. 2. Use [LEFT] or [RIGHT] button to set shutter speed. Note: 1. 2. Use [UP] or [DOWN] button to select [SENS-UP] option.
Note: • If you set to one of the SHUTTER options except AUTO on the [SHUTTER] menu, the [SENS-UP] setting is not available and [---] mark is displayed. White Balance settings Select the method by which the camera shifts its output colors to compensate for the color of a light source. 1. Select [WHITE BAL] option. 2. Use [LEFT] or [RIGHT] button to select a mode then press [SET]. • 20 ATW (Auto-Tracing White Balance): Use [LEFT] or [RIGHT] button to select the ATW then press [SET] button.
Day/Night Setting > • DWELL TIME: Use [LEFT] or [RIGHT] button to select a dwell time. DAY: Color mode enabled. • NIGHT: Black-and-white mode enabled. > 1. Select [DAY/NIGHT] option. 2. Use [LEFT] or [RIGHT] button to select mode for Day/Night function. • BURST: Use [LEFT] or [RIGHT] button to select [ON] or [OFF]. AUTO: You will be able to change the Day/Night mode automatically.
SmartIR Setting SmartIR function improve the sensitivity in the low luminance. SmartIR analyze the image of the screen, when the subject is close. Then SmartIR reduce the IR LED brightness and gain to prevent saturation of the closed subject. • SIZE ;. : Enlarge or decrease the vertical size of the prevent saturation zone. Motion Detection Setting The motion detection detects the moving objects in the scene by monitoring changes in brightness level.
OFF on the STATE. • Use [UP] or [DOWN] to select an option then use [LEFT] or [RIGHT] button to adjust the option. > 4. 5. 6. POSITION ,/: Moves horizontal position of the mask. > POSITION ;.: Moves vertical position of the mask. > SIZE ,/ : Enlarge or decrease the horizontal size of the mask. > SIZE ;. : Enlarge or decrease the vertical size of the mask. Use [SENSITIVITY] option to obtain the optimum detection level. Use [LEFT] or [RIGHT] button to select the DISPLAY option.
Privacy Mask Setting This function is aiming at the protection of personal privacy, selecting a screen part black not to be displayed in the screen. Up to 8 zones can be registered. • use [LEFT] or [RIGHT] button to adjust the option. POSITION,/: Moves horizontal position of the mask. POSITION ;.: Moves vertical position of the mask. SIZE ,/: Enlarge or decrease the horizontal size of the mask. SIZE ;.: Enlarge or decrease the vertical size of the mask. CIRCLE : > 1. Select [PRIVACY] option. 2.
- • SIZE ,/: Enlarge or decrease the horizontal size of the mask. SIZE ;.: Enlarge or decrease the vertical size of the mask. RADIUS SIZE : You can adjust the RADIUS SIZE (0 to 100). POLYGON : > > > > Use [LEFT] or [RIGHT] button to select a mask (MASK1 to MASK2) on the [MASK SELECTION]. Use [LEFT] or [RIGHT] button to set up the OFF, MOSAIC, COLOR 1 to COLOR 8 on the DISPLAY option. Use the [LEFT], [RIGHT], [UP], [DOWN], [SET] button to draw the polygon on the [SHAPE].
Special Menu Settings This menu lets you adjust and set up D-ZOOM, D-EFFECT, SHARPNESS, COLOR, SYNC, USER TITLE, LANGUAGE function by yourself in the SPECIAL menu. 1. Select [SPECIAL] option. 2. Press [SET] button and the SPECIAL menu appears. 26 D-ZOOM (Digital Zoom ) Setting You can select the digital zoom level. 1. Select [D-ZOOM] option on the [SPECIAL] menu. 2. Use [LEFT] or [RIGHT] button to select a [ON] then press [SET] the DIGITAL ZOOM menu appears.
• TILT: Use [LEFT] or [RIGHT] button to move the screen. Note: SHARPNESS Setting The degree to which the boundary of the two portions is clearly distinguished. If you set the [D-ZOOM] to ON, the ZOOM level is set to [x1.0] automatically. D-EFFECT (Digital effect) Setting You can select the digital effect. 1. 2. 1. Select [SHARPNESS] option on the [SPECIAL] menu. 2. Use [LEFT] or [RIGHT] button to change a adjust the option. If you set the sharpness value to higher, the image outline becomes sharp.
COLOR Setting SYNC Setting You can switch the displayed picture to gray scale or color. 1. Select [SYNC] option on the [SPECIAL] menu. 1. Select [COLOR] option on the [SPECIAL] menu. 2. The [SYNC] option is set to [INT] automatically. 2. Use [LEFT] or [RIGHT] button to change a adjust the option. Note: 28 LCU5300-EN Model support only INT(INTERNAL) in SYNC.
USER TITLE Setting LANGUAGE Setting You can use the camera identification to assign a number and character to the camera. To disappear the user title, select [OFF]. Select the viewer language for the camera setup menu and OSD information display. 1. Select [USER TITLE] option on the [SPECIAL] menu. 2. Use [LEFT] or [RIGHT] button to select a [ON] then press [SET]. The USER TITLE menu appears. A 3. 1. Select [LANGUAGE] option on the [SPECIAL] screen. 2.
SYSTEM Setting 4. communication settings. Press [SET] button to confirm your selection. Notes: 1. Select the [SYSTEM] menu. 2. Press [SET] button and the SYSTEM menu appears. 3. Use [UP] or [DOWN] button to select the option. • FACTORY RESET: To reset the camera setting to factory setting, select the [FACTORY RESET] option. • COMMUNICATION > > > 30 > CAMERA ID: You can use the camera identification [CAMERA ID] to assign a number to the camera. Use [LEFT] or [RIGHT] to select a CAMERA ID.
Specification Item LCU5500R-BN Signal System NTSC LCU5500R-BP PAL Image Sensor 6 mm (1/3 Type) CCD Lens 2.8 mm to 11 mm Vari-focal Lens, F1.2 Color Horizontal Resolution 650 TV Lines B/W Day & Night Sens-up Minimum Illumination (30 IRE) S/N Ratio 700 TV Lines ICR (AUTO / DAY / NIGHT) OFF / AUTO(x2, ... x512) Color 0.2 lx @ Sens-up OFF, F1.2 B/W 0 lx @ IR LED ON 50 dB Digital Zoom X16 Sync.
Item LCU5500R-BN Communication LCU5500R-BP RS-485, Coaxial Communication RS-485 LG, Pelco-D, Pelco-P Backlight Compensation OFF / WDR / BLC / HSBLC Privacy Masking 14 Masks DNR 2D + 3D-DNR Protection IP66 Power Source DC 12 V / AC 24 V Power Consumption DC 12 V AC 24 V 490 mA 390 mA Operating Temperature/ Humidity -10 ºC to 50 ºC / 0 % RH to 80 % RH Storage Temperature/ Humidity -20 ºC to 60 ºC / 0 % RH to 90 % RH Dimension (W x H x D) 84 mm x 83.5 mm x 320 mm Weight 1.
