OWNER’S MANUAL Dome Camera Please read this manual carefully before operating your set and retain it for future reference.
1 Safety Information Safety Information 1 Safety Information CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
Safety Information Warning: To reduce a risk of fire or electric shock, do not expose this product to rain or moisture. Caution: This installation should be made by a qu alified service person and should conform to all local codes. Caution: The apparatus should not be exposed to water (dripping or splashing) and no objects filled with liquids, such as vases, should be placed on the apparatus. To disconnect power from mains, pull out the mains cord plug.
Safety Information IMPORTANT SAFETY INSTRUCTIONS 1 Safety Information 1. Read these instructions. 14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 2. Keep these instructions. 3. Heed all warnings. 4.
Safety Information • Consumables Parts having contacts such as the lens-drive motors, cooling fan built inside the camera are subject to wear with time. About replacement and maintenance of such parts, please ask the nearest service center. About Static Electricity Removal Before installing the camera, touch a metal case or other metallic parts with your hand to remove static electricity from your body. Do not install in areas subjected to high amounts of humidity or dust.
Contents Contents 1 Safety Information 4 IMPORTANT SAFETY INSTRUCTIONS 4 Safety Precautions 15 Connecting LKD1000 controller 15 Connecting RS-485 device 16 Connecting power source 16 Protocol and baud rate settings 17 Camera ID Setting 20 Removing the Protection Tape 21 Mounting the camera 21 Wall mount (optional) 23 Pendant mount (Optional) 4 Operation 2 Preparation 27 Setup Menu Overview 31 Menu navigation 8 Introduction 31 Accessing the camera setup menu 8 Features
Contents 38 Auto Pan setting 38 Privacy Mask setting 39 Special setting 41 Auto Tracking setting (Optional) 43 User title setting 43 ZOOM MAG setting 43 FUNCTION setting 44 DOME ID setting 44 LANGUAGE Setting 44 ALARM Setting 44 Alarm In setting 45 Alarm Out setting 2 3 4 RESET Setting 45 Information 45 Initialization 45 Camera reset 45 Factory reset 5 Appendix 46 1 OSD Settings 43 45 7 Specifications 5
Preparation 2 Preparation 2 Preparation Introduction • A routine of manual operations can be stored and reproduced repeatedly. The Pan, Tilt and Zoom controls are available for pattern recording. The dome cameras are designed for installation in an outdoor video surveillance system. The camera incorporates the digital signal processor, pan/ tilt mechanism, zoom lens and RS-485 communication interface in a compact outdoor enclosure.
Preparation • Alarm Out function (2 channels) When alarm inputs are supplied via the alarm input connector on the camera, the camera sends output signals via the alarm output connector on the camera. • Accessories Controls by General Controller This camera can be controlled by RS-485. Especially the camera has an excellent cost-saving effect because it can be controlled by the general RX point of contact signal.
Preparation Part Names and Functions a a BNC connector cover cap b Video output BNC connector Supplies analog video signal (composite) to the connected device. b c c RS-485 Data Communication d Alarm In Data Terminal Input data terminal for alarm (relay) signal. 2 d Preparation e f e Output data terminal for alarm (relay) signal. f Power input Terminal Connects to a AC 24 V power supply using proper cables.
Installation 11 3 Installation Connections Precautions The following steps of installation and connection work should be done by qualified service personnel or system installers and should conform to all local codes. • Before you install and connect the camera, check and prepare the required peripheral devices and cables. • Before you connect the camera, turn off all devices to be connected, such as this camera and DVR. • Do not touch the dome cover’s window.
Installation Connecting Display device The video signal connection between the camera and the monitor. Display device connection >>Caution Do not connect one alarm sensor to the several camera’s alarm input connector. Alarm input connection 3 A Alarm device Installation B Alarm device C Alarm device D E Adaptor Cable Alarm device Alarm In Data Terminal Adaptor cable No Description ALARM input connection A ALARM IN 1 You can connect up to 4 alarm sensors to the camera.
Installation 13 Alarm Input function Alarm In Data Terminal Description Color ALARM IN 1 Pink ALARM IN 2 Gray ALARM IN COM Yellow ALARM IN 3 White ALARM IN 4 Violet This speed dome camera has a terminal that can sense the alarm signals. If the alarm sensor that has installed in a door, window, safe etc. sense a touch or shock, the alarm sensor send the alarm signal to the camera and the camera will observe the sensed position.
Installation ALARM output connections No Description A ALARM OUT [NO1] B ALARM OUT [COM1] C ALARM OUT [NC1] D NC E ALARM OUT [NO2] F ALARM OUT [COM2] 3 G ALARM OUT [NC2] Installation Connect the alarm device to the alarm output data port. Alarm signal output at an event occurrence. You can set the Alarm Output to the normal open or normal close mode. Adaptor cable H NC 1. Connect the adaptor cable to the Alarm Out Data Terminal of the camera. 2.
TXInstallation Connecting LKD1000 controller 15 RS-485 connection 1. Connect the adaptor cable to the RS-485 Data Communication of the camera. 2. Connect the LKD1000 controller to the adaptor cable. (Refer to the manuals of the LKD1000 controller for more details.) LKD1000 connection A RS-485device device RS-485 B TX+ 3 A Adaptor cable TX- RS-485 Data Communication 1. Connect the adaptor cable to the RS-485 Data Communication of the camera.
Installation Connecting power source Connect a AC 24 V power source to the power input jack. (Recommended power adapter is AC 24 V/2 A or above) Baud Rate setting ON ON OFF Protocol and baud rate settings The camera has one 8-bit DIP switch blocks that determine the protocol and baud rate of the data communication. Settings are loaded when the camera boots up. Be sure to turn the camera off, change the DIP switch settings, and then power the camera back up to load the changes.
Installation Camera ID Setting 28 The camera’s ID is set to “0” as factory default. If you use two or more cameras simultaneously, change the ID of the cameras. Set the camera ID setting referring to the pictures and the table on the below.
3 Installation 67 ON 68 69 ON Installation OFF OFF OFF OFF ON OFF 106 OFF ON OFF ON OFF ON ON OFF OFF OFF ON OFF OFF OFF ON OFF ON OFF ON OFF OFF OFF ON OFF 107 ON ON OFF ON OFF ON ON OFF 108 OFF OFF ON ON OFF ON ON OFF 70 OFF ON ON OFF OFF OFF ON OFF 71 ON ON ON OFF OFF OFF ON OFF 109 ON OFF ON ON OFF ON ON OFF 110 OFF ON ON ON OFF ON ON OFF 72 OFF OFF OFF ON OFF OFF ON OFF 73 ON OFF OFF ON OFF OFF ON OFF 111 O
Installation ON OFF OFF OFF ON OFF OFF ON 184 OFF OFF OFF ON ON ON OFF ON 146 OFF ON OFF OFF ON OFF OFF ON 147 ON ON OFF OFF ON OFF OFF ON 185 ON OFF OFF ON ON ON OFF ON 186 OFF ON OFF ON ON ON OFF ON 148 OFF OFF ON OFF ON OFF OFF ON 149 ON OFF ON OFF ON OFF OFF ON 187 ON ON OFF ON ON ON OFF ON 188 OFF OFF ON ON ON ON OFF ON 150 OFF ON ON OFF ON OFF OFF ON 151 ON ON ON OFF ON OFF OFF ON 189 ON OFF ON ON ON ON
3 Installation Installation 223 ON ON OFF ON ON Removing the Protection Tape 224 OFF OFF OFF OFF OFF ON ON ON 225 ON OFF OFF OFF OFF ON ON ON 226 OFF ON OFF OFF OFF ON ON ON You should remove the protection tape before installing the camera. Remove the protection tape carefully.
Installation Mounting the camera 21 3. Drill a hole on the wall where you want to install the pipe. Pass the connection cable through the wall mount assembly so that they hang down. You can mount the camera on the ceiling or wall. Wall mount (optional) Install the camera by the following order. 1. Disassemble the PIPE Installation Bracket to remove the [A] part. [A] 4. Install the wall mount assembly. 3 Installation 2. Install the PIPE Installation Bracket to the Wall Mount assembly.
Installation 5. Connect the connection cable and the safety cable to the camera body. 3 Installation 6. Attach the camera to the camera assembly bracket by following step a and b. Align the locking point of the wall mount assembly and the camera. 7. Tighten the locking screw.
Installation 8. Assemble the camera cover as shown below. 23 Pendant mount (Optional) Install the camera by the following order. 1. Disassemble the PIPE Installation Bracket to remove the [A] part. [A] ,,Note You can install the PIPE Installation Bracket direct to the other type LG Wall Mount assembly. This LG Wall Mount assembly make to easy to install your camera. 3 Installation 2. Install the PIPE Installation Bracket to the Pendant Mount assembly.
Installation 3. Drill a hole on the wall where you want to install the pipe. Pass the connection cable through the pendant mount assembly so that they hang down. 4. Install the pendant mount assembly. 3 Installation 5. Connect the connection cable and the safety cable to the camera body.
Installation 6. Attach the camera to the camera assembly bracket by following step a and b. Align the locking point of the wall mount assembly and the camera. 25 7. Tighten the locking screw.
Installation 8. Assemble the camera cover as shown below. ,,Note You can install the PIPE Installation Bracket direct to the other type LG Wall Mount assembly. This LG Wall Mount assembly make to easy to install your camera.
Operation 27 4 Operation Setup Menu Overview The following table shows the list of menu items and options. You can adapt the camera to your requirements by setting up the respective items in these menus. 1st level 2nd level FOCUS CAMERA SET Contents FOCUS MODE AUTO/MANUAL/ONE PUSH/ZOOM TRIG FOCUS DIST 1 M, 3 M, 6 M ZOOM START x1 to x36 ZOOM END x2 to x444 RETURN - IRIS AUTO/MANUAL AGC OFF, 1 to 10 WDR/BLC OFF/WDR/BLC/HSBLC BRIGHTNESS 0 to 100 SHUTTER OFF, A.
Operation DAY/NIGHT 3D-DNR CAMERA SET COLOR SHARPNESS STABILIZER NIGHT - OFF - LOW - MIDDLE - HIGH - ON COLOR -50 to 50 OFF - 0 to 68 - ON - OFF - RETURN - 4 Operation SET PRESET PRESET PAN/TILT SET OFF/ON SPEED 1 to 127 DWELL TIME 1 to 255 IRIS AUTO, 20, 40, 60, 80, 100 % WDR/BLC/HSBLC OFF/ LOW WDR/ MID. WDR HIGH WDR/ LOW BLC/ MID. BLC / HIGH BLC/ LOW HSBLC / MID. HSBLC/ HIGH HSBLC SHUTTER X512, ..., x2, AUTO, OFF, A.FLK, 1/160, ...
Operation PATTERN AUTO PAN PRIVACY MASK RECORD 1 to 4 RUN 1 to 4 RETURN - SET AUTO PAN 1 to 8 RUN - CLEAR - RETURN - MASK NUMBER 1 to 8 SET MASK - MASK STATE ON/OFF MASK COLOR GRAY, WHITE, BLACK WIDTH 0 to 320 HEIGHT 0 to 240 RETURN - PROPORTIONAL PT ON/OFF COMPASS ON/OFF 4 GO HOME POSITION DWELL TIME (INFINITE to 100 MIN) RETURN SPECIAL AUTO RETURN OFF - ON RETURN TIME (1 MIN to 100 MIN) OFF - TILT LIMIT MOTION DET COMMUNICATION AUTO TRACKING (LCP3750T model
Operation LOST MODE PAN/TILT SET AUTO TRACKING (LCP3750T model only) ACTION STAY / RETURN TIME OUT 10 / 30 S / 1 / 2 / 3 / 4 / 5 MIN RETURN - TRACK TIME INFINITE / 10 / 30 S / 1 / 2 / 3 / 4 / 5 MIN SENSITIVITY LOW / MIDDLE / HIGH RETURN - RETURN OSD SET - USER TITLE ON/OFF - ZOOM MAG ON/OFF - FUNCTION ON/OFF - DOME ID ON/OFF - RETURN - LANGUAGE The option depends on the model.
Operation Please Enter Camera ID Target CAM ID : _ Menu navigation 2. Enter the connected camera ID to control the camera connected to the LKD1000 controller directly and then press ENTER. The camera control menu will be displayed. We use the LKD1000 controller in this manual to explain the features of the LG Dome camera because of the LKD1000’s ability to control all of the LG Dome camera’s advanced features. (For detailed controller instructions, refer to the LKD1000 Controller Manual.
Operation Camera menu settings Focus setting The camera adjusts the focus automatically by sensing the center of the picture. Focus Distance setting Selects the minimum shooting distance for the focus. Select [FOCUS DIST] option on the [FOCUS] menu, then select a focus distance value. Zoom Start setting (Optional) You can set the zoom start position of the camera. When the zoom function is operated, the zoom always will start at the selected zoom start position.
Operation • AUTO: The lens iris is set automatically. • MANUAL: Use [Near] or [Far] button to select the DC Iris level. DC Iris level are set by one parameter unit. SHUTTER (Shutter Speed) setting Select the desired shutter speed for camera exposure. You can change the shutter speed to higher speed to capture fast-moving subjects, though the image becomes darker. AGC (Automatic Gain Control) setting 1. Select [SHUTTER] option on the [EXPOSURE] menu.
Operation • • -- When the scene mostly contains high color temperature objects, such as a blue sky or sunset. -- When the scene is dim. When the color temperature is out of the 3 500 K to 6 500 K range. -- When the scene mostly contains high color temperature objects, such as a blue sky or sun set. -- When the scene is dim. MANUAL: You can set the white balance options manually. -- 4 Operation • -- DWELL TIME: Use [Near] or [Far] button to select a dwell time.
Operation 35 Color setting You can switch the displayed picture to grayscale or color. 1. Select [STABILIZER] option on the [CAMERA SET] menu. 2. Use [Near] or [Far] button to ser it [ON] or [OFF]. 1. Select [COLOR] option on the [CAMERA SET] menu. 2. Use [Near] or [Far] button to change a color effect. • ON: To display the picture with color. Select ON and press [Open] or [Close] to display the submenu. You can adjust the color level using the [Near] or [Far] button.
Operation To register preset positions 1. Select the [SET PRESET] option on the [PRESET] menu. 2. Use the [Near] or [Far] button to select the preset number you wish to register and press the [Open] or [Close] button. 3. Set the preset name. How to set the preset name. 1. Set the NAME option to [ON] and press [Open] or [Close] button. 2. Use [In], [Out], [Near] or [Far] button to select a character, number, symbol mark or option item. 4 • : Moves cursor to left or right.
Operation Group tour setting To delete a group You can create a group using preset positions that are registered already. A maximum of 10 groups is available. 1. Select [CLEAR] option on the [GROUP TOUR] menu. 37 You can delete a memorized group. 2. Select the group number and press [Open] or [Close] button. The group will be deleted. Pattern setting You can activate the camera in a repeating pattern. The pattern is programmed by recording your manual pan, tilt, and zoom operations.
Operation To play the pattern 8. Repeat steps 1 to 7 to add additional positions. 1. Select [RUN] option on the [PATTERN] menu. 9. Select [RETURN] option and press [Open] or [Close] button to exit the setting menu. 2. Select the recording number and then press [Open] or [Close] button to play the programmed pattern. The tour will play indefinitely until you stop it by moving the joystick or pressing any button.
Operation 1. Select [PRIVACY MASK] option on the [PAN/TILT MENU]. 2. Press [Open] or [Close] button to display the PRIVACY MASK MENU. 39 Special setting 3. Use [Near] or [Far] button to select a zone number on the [MASK NUMBER] option. 4. Select the [SET MASK] option and press [Open] or [Close] button. 5. Select the mask zone using the joystick and then press [Open] or [Close] button to save it. 6. Use [Near] or [Far] button to set up the [ON] or [OFF] on the [MASK STATE] option.
Operation Home position Tilt limit Use the following procedure to make the home position. 1. Select [TILT LIMIT] option on the [SPECIAL] menu. 1. Select [HOME POSITION] option on the [SPECIAL] menu. 2. Use [Near] or [Far] button to set it [ON]. If you do not want to use this function, set it to [OFF]. The home position is the camera’s basic position. The camera returns to this position whenever you want. 2. Use [Near] or [Far] button to set it ON. 3. Press [Open] or [Close] button. 4.
Operation Auto Tracking setting (Optional) ,,Note The Auto Tracking option is supported LCP3750T series only. Configure Auto Tracking MENU options. These options are used for tracking the displayed object in motion on the screen. If you want to use the [Auto Tracking] option, use [Near] or [Far] button to set it ON. ,,Note Environmental conditions In the case of following installation conditions, object tracking errors may occur. • Contrast between object and background is low.
Operation Camera Height Use [Near] or [Far] button to select how high the camera is installed. Lost Mode You can configure what the camera will execute when the camera loses the object. • -- 4 STAY : When the camera loses the object, it doesn’t come back to its initial position, but stays where the object has been just lost. RETURN : When the camera loses the object, it returns to its initial position and gets ready to detect a new object.
Operation OSD Settings • CLR: If you enter the wrong code, select [CLR] then press [Open] or [Close]. All letters will be erased at once. • POS: Move the USER TITLE position on the screen using the [Near] or [Far] buttons. • END: Select this option to exit the settings. 43 ZOOM MAG setting Displays or removes the zoom OSD on the screen. . 1. Select [ZOOM MAG] option on the [OSD] menu. 3. Select [RETURN] option and press [Open] or [Close] button to exit the setting menu.
Operation DOME ID setting Displays or removes the Camera ID OSD on the screen. ALARM Setting This camera has a terminal that can sense the alarm signals. The camera can be programmed to go to a preset with a signal from any connected alarm device. 1. Select [DOME ID] option on the [OSD] menu. 2. Use [Near] or [Far] button to set it [ON] or [OFF] 3. Select [RETURN] option and press [Open] or [Close] button to exit the setting menu.
Operation Alarm Out setting Initialization 1. Select one of the alarm out options on the [ALARM SET] menu. You can initialize the camera settings. 2. Use [Near] or [Far] button to set it [ON]. 2. Press [Open] or [Close] button then confirmation window is displayed. 3. Press [Open] or [Close] button. 4. Select alarm input number or motion detection. When the selected alarm input is triggered or motion is detected, the alarm signal is outputted. 5.
Appendix 5 Appendix Specifications Model LCP3750-AN LCP3750-AP LCP3750T-AN LCP3750T-AP Signal System NTSC PAL NTSC PAL Image Sensor 4.5 mm(1/4 Type) Super HAD II CCD Total Pixels Number 520 000 Pixels 610 000 Pixels 520 000 Pixels 610 000 Pixels Effective Pixels Number 490 000 Pixels 570 000 Pixels 490 000 Pixels 570 000 Pixels Horizontal Resolution 600 TV Lines Lens x37 Zoom, F1.5 (Wide End), F4.1(Tele End), f= 3.
Appendix Video Output 1Vp-p Composite (75Ω) Backlight Compensation WDR / BLC / HSBLC / OFF Electric Shutter 1/60 to 1/120 000 1/50 to 1/120 000 1/60 to 1/120 000 3D-DNR OFF / LOW / MIDDLE / HIGH Auto Gain Control ON / OFF Digital Effect Auto Flip Pattern Recording & Play 1 to 4 / 1 to 4 Protection Vandal Proof / IP66 Sens-Up OFF / AUTO / MANUAL Iris Control AUTO / MANUAL Stabilizer ON / OFF Motion Detection Support Auto Tracking Not Support 1/50 to 1/120 000 Support 0 ˚ to 360
AB28
